1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
25051
2.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)
17167
3.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o EGR Cooler)
17271
4.REMOVE NO. 1 TURBO INSULATOR (w/o EGR Cooler)
5.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)
6.REMOVE EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)
17291
7.REMOVE TURBINE OUTLET ELBOW (w/o EGR Cooler)
8.DRAIN ENGINE COOLANT
9.DRAIN ENGINE COOLANT (w/ Urea SCR System)
10.DRAIN ENGINE OIL
17940D
11.REMOVE INTERCOOLER ASSEMBLY (w/ Urea SCR System)
17341K
12.REMOVE INTERCOOLER AIR HOSE (w/o Urea SCR System)
17342F
13.REMOVE NO. 2 INTERCOOLER AIR HOSE (w/o Urea SCR System)
44306
14.DISCONNECT VANE PUMP OIL RESERVOIR SUB-ASSEMBLY
16571C
15.REMOVE NO. 1 RADIATOR HOSE
16552B
16.REMOVE NO. 2 SUB-RADIATOR HOSE (w/ Urea SCR System)
16551B
17.REMOVE NO. 1 SUB-RADIATOR HOSE (w/ Urea SCR System)
161B0
18.REMOVE ELECTRIC WATER PUMP ASSEMBLY (w/ Urea SCR System)
16553B
19.REMOVE NO. 3 SUB-RADIATOR HOSE (w/ Urea SCR System)
16554B
20.REMOVE NO. 4 SUB-RADIATOR HOSE (w/ Urea SCR System)
16640
21.REMOVE INTERCOOLER RESERVOIR ASSEMBLY
16470
22.REMOVE RADIATOR RESERVOIR ASSEMBLY
82123
23.DISCONNECT NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)
16711
24.REMOVE FAN SHROUD
17705
25.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE
Disconnect the mass air flow meter sub-assembly connector and detach the 2 harness clamps.
Detach the 4 clips.
Loosen the hose clamp and remove the air cleaner cap sub-assembly with air cleaner hose.
17801
26.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner element sub-assembly from the air cleaner case.
27.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
| *A | for Cold Area Specification Vehicles |
Remove the 3 bolts and air cleaner case sub-assembly.
87120G
28.DISCONNECT VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (for Cold Area Specification Vehicles)
87209D
29.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)
16279
30.REMOVE NO. 3 WATER BY-PASS PIPE
for Cold Area Specification Vehicles:
Slide the 2 clips and remove the water hose from the compressor inlet elbow and No. 3 water by-pass pipe.
| *A | for Cold Area Specification Vehicles |
| *B | except Cold Area Specification Vehicles |
Slide the 2 clips and disconnect the 2 water hoses from the oil cooler assembly and No. 2 water by-pass pipe.
Remove the bolt and No. 3 water by-pass pipe.
12229
31.REMOVE PCV PIPE
w/o Urea SCR System for Cold Area Specification Vehicles:
Slide the 2 clips and disconnect the No. 20 water by-pass hose from the PCV pipe and No. 1 water by-pass pipe.
Slide the clip and disconnect the No. 19 water by-pass hose from the compressor inlet elbow.
Remove the bolt and disconnect the PCV pipe from the compressor outlet elbow.
Slide the 2 clips and remove the PCV pipe.
w/ Urea SCR System:
Slide the 2 clips and disconnect the No. 20 water by-pass hose from the PCV pipe and No. 1 water by-pass pipe.
Slide the clip and disconnect the No. 19 water by-pass hose from the compressor inlet elbow.
Remove the 2 bolts and disconnect the PCV pipe from the compression outlet elbow.
Slide the 2 clips and remove the PCV pipe.
12261
32.REMOVE PCV HOSE (except Cold Area Specification Vehicles)
w/o Urea SCR System:
Slide the 2 clips.
Slide the 2 clips, detach the clamp and remove the PCV hose.
33.REMOVE WATER BY-PASS HOSE
Slide the 2 clips and disconnect the No. 21 water by-pass hose from the turbocharger sub-assembly and No. 1 water by-pass pipe.
Slide the 2 clips and disconnect the No. 4 turbo water hose from the turbocharger sub-assembly and No. 1 turbo water pipe sub-assembly.
16268
34.REMOVE NO. 1 WATER BY-PASS PIPE
16284
35.DISCONNECT TURBO WATER HOSE
Slide the 2 clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the water outlet sub-assembly and water pump assembly.
36.REMOVE OIL COOLER TUBE BRACKET AND WIREHARNESS CLAMP BRACKET
for Automatic Transmission:
Remove the 2 bolts and disconnect the oil cooler tube bracket.
Remove the bolt and disconnect the wire harness clamp bracket.
87101
37.DISCONNECT NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)
Remove the bolt and disconnect the wire harness.
|
No. 1 Viscous Heater Bracket Sub-assembly Bolt |
|
No. 4 Engine Harness Bolt |
Remove the bolt and disconnect the No. 4 engine harness.
Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly.
17293
38.REMOVE TURBOCHARGER STAY
Remove the 3 bolts, nut and the turbocharger stay.
15474
39.REMOVE TURBO OIL OUTLET PIPE
Slide the 2 clips and disconnect the turbo oil outlet hose from the turbo oil outlet pipe.
w/ Cover:
Remove the cover from the turbo oil outlet pipe.
Remove the 2 bolts and turbo oil outlet pipe and gasket.
15407
40.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
Remove the union bolt and gasket.
Remove the 2 nuts and the turbo oil inlet pipe subassembly.
Do not loosen the nut labeled A.
Remove the gasket.
17201
41.REMOVE TURBOCHARGER SUB-ASSEMBLY
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Remove the 3 nuts and turbocharger sub-assembly.
Remove the gasket from the exhaust manifold.
25601
42.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
Remove the 2 nuts and disconnect the No. 1 EGR pipe sub-assembly.
25617
43.REMOVE EGR HOLE COVER PLATE (w/o EGR System)
Remove the 2 nuts, EGR hole cover plate and gasket.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts shown in the illustration.
17141
44.REMOVE EXHAUST MANIFOLD
| *A | w/ DPF |
| *B | w/o DPF |
Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.
Remove the 2 gaskets (cylinder head side and No. 1 EGR pipe sub-assembly side).
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.
16027
45.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY
| *A | w/ DPF |
| *B | w/o DPF |
Slide the 2 hose clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the No. 1 turbo water pipe sub-assembly.
Remove the bolt.
Remove the 2 nuts, turbo water pipe sub-assembly and gasket.
17274
46.REMOVE COMPRESSOR INLET ELBOW
Remove the 2 bolts and compressor elbow stay.
Remove the 2 nuts and compressor inlet elbow from turbocharger sub-assembly.
Using an E8 "TORX" socket wrench, remove the stud bolt shown in the illustration together with the compressor inlet elbow.
Remove the gasket from the compressor inlet elbow.
17275
47.REMOVE COMPRESSOR OUTLET ELBOW
w/o Urea SCR System:
Remove the 2 nuts and compressor outlet elbow.
Remove the gasket.
| *A | except Cold Area Specification Vehicles |
except Cold Area Specification Vehicles:
Remove the bolt and hose clamp.
w/ Urea SCR System:
Remove the 2 nuts and compressor outlet elbow.
Remove the gasket.
48.DISCONNECT STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
Using an E5 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.
Using an E8 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.
Using an E10 "TORX" socket wrench, remove the 3 stud bolts shown in the illustration.