Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1501  Sub Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a No. 2 fuel sender gauge assembly malfunction via a direct line.

DTC Code DTC Detection Condition Trouble Area
B1501 Both conditions are met:
·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.

·

Average input signal of fuel sender gauge is 630 Ω or more 3 times consecutively.


·

Harness or connector

·

Combination meter assembly

·

Fuel tank vent tube sub-assembly

·

Fuel sender gauge assembly



WIRING DIAGRAM

except 5L-E:
E380648E13
0.656,2.792 2.219,3.177 1.563,0.385 10 false No.2 Fuel Sender Gauge Assembly 0.521,3.542 3.052,3.729 2.531,0.188 10 false Fuel Tank Vent Tube Sub-assembly 3.896,4.021 5.813,4.302 1.917,0.281 10 false Combination Meter Assembly 3.896,3.833 5.813,4.115 1.917,0.281 10 false G304 0.521,3.365 3.052,3.552 2.531,0.188 10 false t1 2.271,1.927 2.583,2.156 0.313,0.229 10 false FR2 2.25,2.427 2.594,2.667 0.344,0.24 10 false FE2 2.229,1.469 2.688,1.677 0.458,0.208 10 false FV2 3.979,1.469 4.333,1.719 0.354,0.25 10 false L 3.958,1.906 4.302,2.146 0.344,0.24 10 false FR 3.938,2.417 4.469,2.667 0.531,0.25 10 false FE 3.708,1.469 4.167,1.677 0.458,0.208 10 false 25 3.698,1.927 4.156,2.135 0.458,0.208 10 false 26 3.771,2.427 4.229,2.635 0.458,0.208 10 false 2 2.625,1.448 3.083,1.656 0.458,0.208 10 false 5 2.625,1.896 3.083,2.104 0.458,0.208 10 false 4 2.625,2.406 3.083,2.615 0.458,0.208 10 false 1 1.823,1.563 2.281,1.771 0.458,0.208 10 false 1 1.833,2.5 2.292,2.708 0.458,0.208 10 false 2 1.823,2.042 2.281,2.25 0.458,0.208 10 false 3

for 5L-E:
E321084E19
5.177,0.781 5.385,1.042 0.208,0.26 10 false L 5.177,1.406 5.458,1.677 0.281,0.271 10 false FE 5.021,3.906 5.344,4.125 0.323,0.219 10 false G6 5.177,3.25 5.49,3.479 0.313,0.229 10 false ET 4.917,3.25 5.167,3.5 0.25,0.25 10 false 5 4.979,0.823 5.188,1.083 0.208,0.26 10 false 8 4.906,1.396 5.135,1.677 0.229,0.281 10 false 23 3.5,0.813 3.677,1.073 0.177,0.26 10 false 4 3.5,1.406 3.708,1.667 0.208,0.26 10 false 5 5.031,4.094 6.875,4.333 1.844,0.24 10 false Combination Meter Assembly 2.771,1.396 2.938,1.646 0.167,0.25 10 false 2 1.635,1.417 1.906,1.74 0.271,0.323 10 false 1 1.01,2.417 1.323,2.646 0.313,0.229 10 false t1 1,2.615 3.438,2.896 2.438,0.281 10 false Fuel Tank Vent Tube Sub-assembly 1.135,1.833 3.51,2.042 2.375,0.208 10 false No.2 Fuel Sender Gauge Assembly 3.135,1.406 3.458,1.635 0.323,0.229 10 false FV2 3.135,0.813 3.469,1 0.333,0.188 10 false FR2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sub Fuel Input Fuel input signal/Min.: 0, Max. 127.5 Current fuel level displayed Unit: Liter


Result:
Result Proceed to
Fuel level data can be displayed on the GTS A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
except 5L-E A
for 5L-E B



A

3.INSPECT NO.2 FUEL SENDER GAGE ASSEMBLY

B

6.INSPECT NO.2 FUEL SENDER GAGE ASSEMBLY
3.INSPECT NO.2 FUEL SENDER GAGE ASSEMBLY


Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL TANK VENT TUBE SUB-ASSEMBLY

NG

4.INSPECT FUEL TANK VENT TUBE SUB-ASSEMBLY
E380660C02
1.688,2.74 2.094,2.969 0.406,0.229 0.833,2.583 0.667,2.583 0.667,2.583 1.688,1.104 true 1.5,2.333 1.313,2.333 1.313,2.333 1.865,1.073 true 2.083,1.917 1.833,1.917 1.833,1.917 2.063,1.083 true 1.594,0.375 1.906,0.573 0.313,0.198 10 false *a 0.906,2.479 1.219,2.677 0.313,0.198 10 false 3 1.573,2.25 1.885,2.448 0.313,0.198 10 false 2 2.156,1.833 2.469,2.031 0.313,0.198 10 false 1 0.188,2.99 0.5,3.188 0.313,0.198 10 false *b 1.813,2.781 2.125,2.979 0.313,0.198 10 false t1
*a Fuel Tank Vent Tube Sub-assembly
*b Component without harness connected
(Fuel Tank Vent Tube Sub-assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-1 (FE2) - 2 Always Below 1 Ω
t1-4 (FR2) - 3 Always Below 1 Ω
t1-5 (FV2) - 1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the t1 fuel tank vent tube sub-assembly connector.


b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-4 (FR2) - G304-26 (FR) Always Below 1 Ω
t1-1 (FE2) - G304-2 (FE) Always Below 1 Ω
t1-5 (FV2) - G304-25 (L) Always Below 1 Ω
G304-26 (FR) - Body ground Always 10 kΩ or higher
G304-2 (FE2) - Body ground Always 10 kΩ or higher
G304-25 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT NO.2 FUEL SENDER GAGE ASSEMBLY
a.

Remove the No.2 fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the No.2 fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the t1 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-8 (L) - t1-4 (FR2) Always Below 1 Ω
G6-23 (FE) - t1-5 (FV2) Always Below 1 Ω
G6-5 (ET) - Body ground Always Below 1 Ω
G6-8 (L) or t1-4 (FR2) - Body ground Always 10 kΩ or higher
G6-23 (FE) or t1-5 (FV2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL TANK VENT TUBE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FUEL TANK VENT TUBE SUB-ASSEMBLY
E349680C03
1.5,2.813 1.906,3.021 0.406,0.208 1.698,1.802 1.698,0.844 false 2.094,1.802 2.094,0.833 false 0.688,4.292 0.844,4.292 0.844,4.292 1.563,3.979 false 2.75,4.313 2.594,4.313 2.594,4.313 1.802,3.979 false 0.635,0.104 0.948,0.302 0.313,0.198 10 false *a 1.656,1.844 1.813,2.042 0.156,0.198 10 false 2 2.063,1.844 2.219,2.042 0.156,0.198 10 false 1 0.948,3.021 1.26,3.219 0.313,0.198 10 false *b 0.406,4.219 0.917,4.479 0.51,0.26 10 false FV2 2.813,4.229 3.25,4.417 0.438,0.188 10 false FR2 1.646,2.833 1.865,3.073 0.219,0.24 10 false A
*a Fuel Tank Vent Tube Sub-assembly
*b Component without harness connected
(Fuel Tank Vent Tube Sub-assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 (FR2) - 1 Always Below 1 Ω
A-5 (FV2) - 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL TANK VENT TUBE SUB-ASSEMBLY