DTC C1683 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly to the parking assist ECU.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1683 | Side Camera Feedback Malfunction | ·
Harness or connector ·
Parking assist ECU ·
Side television camera assembly RH (for LHD) ·
Outer rear view mirror assembly RH (for LHD) ·
Side television camera assembly LH (for RHD) ·
Outer rear view mirror assembly LH (for RHD) |
for LHD
for RHD
When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
DTC C1683 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Disconnect the I7 parking assist ECU connector.
Disconnect the J11 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-31 (SCB+) - J11-6 (DCB+) | Always | Below 1 Ω |
| I7-10 (SCV+) - J11-2 (DCV+) | Always | Below 1 Ω |
| I7-33 (SCV-) - J11-3 (DCV-) | Always | Below 1 Ω |
| I7-32 (SGND) - J11-7 (DGND) | Always | Below 1 Ω |
| I7-31 (SCB+) or J11-6 (DCB+) - Body ground | Always | 10 kΩ or higher |
| I7-10 (SCV+) or J11-2 (DCV+) - Body ground | Always | 10 kΩ or higher |
| I7-33 (SCV-) or J11-3 (DCV-) - Body ground | Always | 10 kΩ or higher |
| I7-32 (SGND) or J11-7 (DGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 32 (SGND) - Body ground | Always | Below 1 Ω |
| 33 (SCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the outer rear view mirror assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-31 (SCB+) - I7-32 (SGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
| I7-31 (SCB+) - I7-32 (SGND) | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly RH.
A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly RH.
| Item | Content |
|---|---|
| Tester Connection | I7-10 (SCV+) - I7-32 (SGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Side Television Camera Assembly RH) |
| *b | Component without harness connected
(to Outer Mirror Actuator Assembly RH) |
Disconnect the outer rear view mirror assembly RH connector.
Disconnect the side television camera assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (SCB+) - J11-6 (DCB+) | Always | Below 1 Ω |
| A-3 (SCV+) - J11-2 (DCV+) | Always | Below 1 Ω |
| A-7 (SCV-) - J11-3 (DCV-) | Always | Below 1 Ω |
| A-5 (SGND) - J11-7 (DGND) | Always | Below 1 Ω |
| A-1 (SCB+) or J11-6 (DCB+) - Body ground | Always | 10 kΩ or higher |
| A-3 (SCV+) or J11-2 (DCV+) - Body ground | Always | 10 kΩ or higher |
| A-7 (SCV-) or J11-3 (DCV-) - Body ground | Always | 10 kΩ or higher |
| A-5 (SGND) or J11-7 (DGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly RH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
DTC C1683 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I7 parking assist ECU connector.
Disconnect the K11 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-31 (SCB+) - K11-6 (SCB+) | Always | Below 1 Ω |
| I7-10 (SCV+) - K11-2 (SCV+) | Always | Below 1 Ω |
| I7-33 (SCV-) - K11-3 (SCV-) | Always | Below 1 Ω |
| I7-32 (SGND) - K11-7 (SGND) | Always | Below 1 Ω |
| I7-31 (SCB+) or K11-6 (SCB+) - Body ground | Always | 10 kΩ or higher |
| I7-10 (SCV+) or K11-2 (SCV+) - Body ground | Always | 10 kΩ or higher |
| I7-33 (SCV-) or K11-3 (SCV-) - Body ground | Always | 10 kΩ or higher |
| I7-32 (SGND) or K11-7 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 32 (SGND) - Body ground | Always | Below 1 Ω |
| 33 (SCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the outer rear view mirror assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-31 (SCB+) - I7-32 (SGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
| I7-31 (SCB+) - I7-32 (SGND) | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly LH.
A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly LH.
The video waveform is constantly output when the engine switch is on (ACC).
| Item | Content |
|---|---|
| Tester Connection | I7-10 (SCV+) - I7-32 (SGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Side Television Camera Assembly LH) |
| *b | Component without harness connected
(to Outer Mirror Actuator Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
Disconnect the side television camera assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 (SCB+) - K11-6 (SCB+) | Always | Below 1 Ω |
| B-3 (SCV+) - K11-2 (SCV+) | Always | Below 1 Ω |
| B-7 (SCV-) - K11-3 (SCV-) | Always | Below 1 Ω |
| B-5 (SGND) - K11-7 (SGND) | Always | Below 1 Ω |
| B-1 (SCB+) or K11-6 (SCB+) - Body ground | Always | 10 kΩ or higher |
| B-3 (SCV+) or K11-2 (SCV+) - Body ground | Always | 10 kΩ or higher |
| B-7 (SCV-) or K11-3 (SCV-) - Body ground | Always | 10 kΩ or higher |
| B-5 (SGND) or K11-7 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly LH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
DTC C1683 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG