Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0328431 MULTI-TERRAIN MONITOR SYSTEM C

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  C1687  Over Current Detected in Driver Side Camera  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.

DTC Code DTC Detection Condition Trouble Area
C1687 Side camera current malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH (for LHD)

·

Outer rear view mirror assembly LH (for LHD)

·

Side television camera assembly RH (for RHD)

·

Outer rear view mirror assembly RH (for RHD)



WIRING DIAGRAM

for LHD


E382441E03
5.677,1.792 7.156,2.042 1.479,0.25 10 false Parking Assist ECU 5.719,1.604 6.031,1.802 0.313,0.198 10 false I7 5.948,1.073 6.406,1.323 0.458,0.25 10 false DGND 5.948,0.583 6.406,0.833 0.458,0.25 10 false DCB+ 5.667,0.479 6.01,0.667 0.344,0.188 10 false 2 5.677,0.958 6.021,1.146 0.344,0.188 10 false 3 3.99,0.979 4.333,1.167 0.344,0.188 10 false 7 3.99,0.521 4.333,0.708 0.344,0.188 10 false 6 4.927,1.229 5.24,1.406 0.313,0.177 10 false * 3.354,0.927 3.813,1.177 0.458,0.25 10 false SGND 3.385,0.469 3.844,0.719 0.458,0.25 10 false SCB+ 1.042,0.563 1.5,0.813 0.458,0.25 10 false SCB+ 1,1.021 1.458,1.271 0.458,0.25 10 false SGND 1.583,0.479 1.927,0.667 0.344,0.188 10 false 1 1.583,0.979 1.927,1.167 0.344,0.188 10 false 5 0.667,1.396 1.01,1.583 0.344,0.188 10 false B 0.625,1.594 3.281,1.781 2.656,0.188 10 false Side Television Camera Assembly LH 0.531,2.104 0.875,2.292 0.344,0.188 10 false K11 0.51,2.26 3.167,2.448 2.656,0.188 10 false Outer Rear View Mirror Assembly LH 0.51,2.51 1.167,2.75 0.656,0.24 10 false *: Shilded


for RHD


E382441E04
5.677,1.792 7.156,2.042 1.479,0.25 10 false Parking Assist ECU 5.719,1.604 6.031,1.802 0.313,0.198 10 false I7 5.948,1.073 6.406,1.323 0.458,0.25 10 false DGND 5.948,0.583 6.406,0.833 0.458,0.25 10 false DCB+ 5.667,0.5 6.01,0.688 0.344,0.188 10 false 2 5.677,0.958 6.021,1.146 0.344,0.188 10 false 3 3.99,0.979 4.333,1.167 0.344,0.188 10 false 7 3.99,0.521 4.333,0.708 0.344,0.188 10 false 6 4.927,1.229 5.24,1.406 0.313,0.177 10 false * 3.354,0.927 3.813,1.177 0.458,0.25 10 false DGND 3.385,0.469 3.844,0.719 0.458,0.25 10 false DCB+ 1.042,0.563 1.5,0.813 0.458,0.25 10 false SCB+ 1,1.021 1.458,1.271 0.458,0.25 10 false SGND 1.583,0.479 1.927,0.667 0.344,0.188 10 false 1 1.583,0.979 1.927,1.167 0.344,0.188 10 false 5 0.667,1.396 1.01,1.583 0.344,0.188 10 false A 0.625,1.594 3.281,1.781 2.656,0.188 10 false Side Television Camera Assembly RH 0.531,2.104 0.875,2.292 0.344,0.188 10 false J11 0.51,2.26 3.167,2.448 2.656,0.188 10 false Outer Rear View Mirror Assembly RH 0.49,2.521 1.208,2.792 0.719,0.271 10 false *: Shilded


CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK FOR DTC


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)

C

7.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the I7 parking assist ECU connector.


b.

Disconnect the K11 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-2 (DCB+) - K11-6 (SCB+) Always Below 1 Ω
I7-3 (DGND) - K11-7 (SGND) Always Below 1 Ω
I7-2 (DCB+) or K11-6 (SCB+) - Body ground Always 10 kΩ or higher
I7-3 (DGND) or K11-7 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU
a.
E245958C78
1.417,0.25 1.917,0.5 0.5,0.25 1.938,0.677 2.115,0.677 2.115,0.677 2.323,1.01 true 2.427,0.99 2.542,0.688 2.542,0.688 2.729,0.688 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 2.802,0.615 3.198,0.771 0.396,0.156 10 false DCB+ 1.469,0.615 2.031,0.771 0.563,0.156 10 false DGND 1.573,0.313 2.073,0.469 0.5,0.156 10 false I7
*a Component with harness connected
(Parking Assist ECU)


Disconnect the outer rear view mirror assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-3 (DGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I7-2 (DCB+) - I7-3 (DGND) Engine switch on (ACC) 5.5 to 7.05 V
I7-2 (DCB+) - I7-3 (DGND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
E380692C07
1.552,0.167 1.844,0.396 0.292,0.229 1.958,0.948 2.344,0.458 2.344,0.458 2.469,0.458 true 1.979,1.229 2.271,1.563 2.271,1.563 2.417,1.563 true 1.615,2.802 1.25,3.25 1.25,3.25 1.115,3.25 true 1.74,2.802 2.073,3.229 2.073,3.229 2.198,3.229 true 0.271,0.375 0.448,0.552 0.177,0.177 10 false *a 0.302,1.719 0.479,1.896 0.177,0.177 10 false *b 1.656,0.208 1.781,0.365 0.125,0.156 10 false B 2.542,0.396 2.969,0.573 0.427,0.177 10 false SCB+ 2.469,1.51 2.979,1.76 0.51,0.25 10 false SGND 0.74,3.188 1.24,3.427 0.5,0.24 10 false SCB+ 2.25,3.177 2.844,3.427 0.594,0.25 10 false SGND
*a Component without harness connected
(to Side Television Camera Assembly LH)
*b Component without harness connected
(to Outer Mirror Actuator Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the side television camera assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (SCB+) - K11-6 (SCB+) Always Below 1 Ω
B-5 (SGND) - K11-7 (SGND) Always Below 1 Ω
B-1 (SCB+) or K11-6 (SCB+) - Body ground Always 10 kΩ or higher
B-5 (SGND) or K11-7 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG

7.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the I7 parking assist ECU connector.


b.

Disconnect the J11 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-2 (DCB+) - J11-6 (DCB+) Always Below 1 Ω
I7-3 (DGND) - J11-7 (DGND) Always Below 1 Ω
I7-2 (DCB+) or J11-6 (DCB+) - Body ground Always 10 kΩ or higher
I7-3 (DGND) or J11-7 (DGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK PARKING ASSIST ECU
a.
E245958C78
1.417,0.25 1.917,0.5 0.5,0.25 1.938,0.677 2.115,0.677 2.115,0.677 2.323,1.01 true 2.427,0.99 2.542,0.688 2.542,0.688 2.729,0.688 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 2.802,0.615 3.198,0.771 0.396,0.156 10 false DCB+ 1.469,0.615 2.031,0.771 0.563,0.156 10 false DGND 1.573,0.313 2.073,0.469 0.5,0.156 10 false I7
*a Component with harness connected
(Parking Assist ECU)


Disconnect the outer rear view mirror assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-3 (DGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I7-2 (DCB+) - I7-3 (DGND) Engine switch on (ACC) 5.5 to 7.05 V
I7-2 (DCB+) - I7-3 (DGND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

9.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

9.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E380692C08
1.552,0.167 1.844,0.396 0.292,0.229 1.958,0.948 2.344,0.458 2.344,0.458 2.469,0.458 true 1.979,1.229 2.271,1.563 2.271,1.563 2.417,1.563 true 1.615,2.802 1.25,3.25 1.25,3.25 1.115,3.25 true 1.74,2.802 2.073,3.229 2.073,3.229 2.198,3.229 true 0.271,0.375 0.448,0.552 0.177,0.177 10 false *a 0.302,1.719 0.479,1.896 0.177,0.177 10 false *b 1.667,0.208 1.792,0.365 0.125,0.156 10 false A 2.542,0.396 2.969,0.573 0.427,0.177 10 false SCB+ 2.469,1.5 2.99,1.76 0.521,0.26 10 false SGND 0.719,3.177 1.188,3.375 0.469,0.198 10 false DCB+ 2.271,3.167 2.906,3.427 0.635,0.26 10 false DGND
*a Component without harness connected
(to Side Television Camera Assembly RH)
*b Component without harness connected
(to Outer Mirror Actuator Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


b.

Disconnect the side television camera assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (SCB+) - J11-6 (DCB+) Always Below 1 Ω
A-5 (SGND) - J11-7 (DGND) Always Below 1 Ω
A-1 (SCB+) or J11-6 (DCB+) - Body ground Always 10 kΩ or higher
A-5 (SGND) or J11-7 (DGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

10.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC

OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG