Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0328431 MULTI-TERRAIN MONITOR SYSTEM J

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the SIGNAL CHECK screen, it is possible to check if the signals sent to the parking assist ECU are normal (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DIAGNOSIS SYSTEM).

HINT:
·

On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver

*1: for Vacuum Brake Booster

*2: for Hydraulic Brake Booster

CAN CAN communication CAN communication signal DTC is not output Related ECUs
CAM CAN CAN communication CAN communication signal DTC is output
·

Front television camera assembly

·

Rear television camera assembly

·

Side television camera assembly LH

·

Side television camera assembly RH


CAMERA SW Vehicle wire harness Panoramic view monitor switch (multi-terrain monitor switch) signal DTC is not output Panoramic view monitor switch (multi-terrain monitor switch)
SHIFT CAN communication Shift information signal DTC is output ECM
HANDLE CAN communication Handle information signal DTC is output Main body ECU (multiplex network body ECU)
T/M CAN communication Transmisson information signal DTC is output ECM
VSC CAN communication VSC information signal DTC is output Brake actuator assembly (skid control ECU)*1
Master cylinder solenoid (skid control ECU)*2
BODY CAN communication Body size information signal DTC is output Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

E377027E03
2.677,0.396 2.813,0.563 0.135,0.167 10 false E 3.448,0.385 3.76,0.542 0.313,0.156 10 false ECU 2.49,0.385 2.625,0.552 0.135,0.167 10 false 2 3.833,0.385 3.969,0.552 0.135,0.167 10 false 5 5.552,0.365 5.688,0.531 0.135,0.167 10 false 5 5.771,0.49 6.208,0.646 0.438,0.156 10 false MPOS 0.833,2.354 2.844,2.573 2.01,0.219 10 false : CAN Communication Line 2.219,0.885 2.604,1.052 0.385,0.167 10 false G231 2.24,1.031 4.198,1.438 1.958,0.406 10 false Panoramic View Monitor Switch (Multi-terrain Monitor Switch) 5.688,2.094 6.073,2.26 0.385,0.167 10 false I6 5.688,2.271 6.958,2.552 1.271,0.281 10 false Parking Assist ECU

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

(See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION)

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E453541

Check which items display on the SIGNAL CHECK screen.

Result
Result Proceed to
"CAMERA SW" displays "CHK" (red) A
"CAN", "SHIFT", "HANDLE", "T/M", "VSC" or "BODY" displays "CHK" (red) B
"CAM CAN" displays "CHK" (red) C



A

2.INSPECT PANORAMIC VIEW MONITOR SWITCH (MULTI-TERRAIN MONITOR SWITCH)

B

C

2.INSPECT PANORAMIC VIEW MONITOR SWITCH (MULTI-TERRAIN MONITOR SWITCH)
a.

Remove the panoramic view monitor switch (multi-terrain monitor switch) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SWITCH>REMOVAL).


b.

Inspect the panoramic view monitor switch (multi-terrain monitor switch) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH [MULTI-TERRAIN MONITOR SWITCH] - PARKING ASSIST ECU AND BODY GROUND))

NG

REPLACE PANORAMIC VIEW MONITOR SWITCH (MULTI-TERRAIN MONITOR SWITCH)

3.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH [MULTI-TERRAIN MONITOR SWITCH] - PARKING ASSIST ECU AND BODY GROUND))
a.

Disconnect the G231 panoramic view monitor switch (multi-terrain monitor switch) connector.


b.

Disconnect the I6 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G231-5 (ECU) - I6-5 (MPOS) Always Below 1 Ω
G231-2 (IG) - Body ground Always Below 1 Ω
G231-5 (ECU) or I6-5 (MPOS) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR