Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY › from 2021.06
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261096 FRONT SEAT SIDE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side. (for Manual Seat, Power Seat)

·

The procedure listed below is for the RH side. (for Walk in Seat Type)



PROCEDURE

Hide 73920A 1.INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
·

The nuts must not be reused.

·

Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.



HINT:

Use the same procedure for the RH and LH sides.


a.

Install the front seat side airbag assembly with 2 new nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

for Type A:

i.

Attach the 2 clamps.



c.

for Type B:

i.

Attach the clamp.



Hide 2.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

HINT:

Use the same procedure for the RH and LH sides.


a.

Temporarily install the separate type front seatback cover with pad.


b.

Attach the 4 claws to install the 2 front seat headrest supports.


c.

Connect the seatback cover bracket to the separate type front seatback pad.

B617503C01
0.594,0.26 0.969,0.5 0.375,0.24 12 false *A 3.958,0.281 4.333,0.521 0.375,0.24 12 false *B
*A for Type A *B for Type B



d.

Install the seatback cover bracket to the seat frame with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:
·

For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.

·

Check that the strap is not twisted after installing the bracket.

·

Install the bracket securely.




e.

w/o Seatback Board:

i.

Close the 2 fasteners, and then close the seatback cover.

B242233C04
0.875,0.052 1.219,0.354 0.344,0.302 12 false *A 4.271,0.052 4.604,0.313 0.333,0.26 12 false *B
*A for Cloth Seat *B for Leather Seat



ii.
B333280C01
1.854,3.719 2.083,2.49 2.083,2.49 2.354,2.49 false 2.385,2.406 2.667,2.646 0.281,0.24 10 false *a
*a Hog Ring Pliers


Using hog ring pliers, install 3 new hog rings.

NOTICE:

Be sure to securely install the hog rings as shown in the illustration.




f.

w/ Seatback Board:

i.
B247942C04
2.229,0.469 2.083,0.469 2.083,0.469 1.656,1.677 false 2.26,0.396 2.49,0.594 0.229,0.198 10 false *a
*a Hog Ring Pliers


Using hog ring pliers, install 5 new hog rings.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




ii.

Attach the hooks.


iii.

Connect the seat heater connector and attach the wire harness clamp.



g.

w/ Seat Heater System:

Connect the seat heater connector and attach the wire harness clamp.


Hide 73920A 3.CONNECT FRONT SEAT SIDE AIRBAG ASSEMBLY

a.

for Manual Seat, Power Seat:

i.

Connect the airbag wire harness.


ii.

Attach the fastening tape and close the cover.


iii.

Attach the hook and 3 airbag wire harness clamps.


iv.

Attach the claw and connect the airbag connector.



b.

for Walk in Seat Type:

i.

Connect the airbag wire harness.


ii.

Attach the fastening tape and close the cover.


iii.

Attach the hook and 3 airbag wire harness clamps.


iv.

Attach the claw and connect the airbag connector.


v.

Install the rubber band to the seat cushion spring.



c.

w/o Seatback Board:

i.

Install the rubber band to the seat cushion spring.



Hide 71706B 4.INSTALL FRONT SEATBACK BOARD CLIP (w/ Seatback Board)

Hide 71706 5.INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)

Hide 72158 8.INSTALL INNER SEAT TRACK BRACKET COVER LH

Hide 72124 9.INSTALL FRONT SEAT OUTER TRACK BRACKET COVER LH

Hide 72128A 10.INSTALL FRONT SEAT INNER TRACK BRACKET COVER LH

Hide 72137B 11.INSTALL SEAT TRACK COVER RH (for Walk in Seat Type)

Hide 72157A 12.INSTALL INNER SEAT TRACK BRACKET COVER RH (for Walk in Seat Type)

Hide 72123A 13.INSTALL FRONT SEAT OUTER TRACK BRACKET COVER RH (for Walk in Seat Type)

Hide 72127A 14.INSTALL FRONT SEAT INNER TRACK BRACKET COVER RH (for Walk in Seat Type)

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 17. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 18.CHECK SRS WARNING LIGHT