Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) › from 2021.06
RM27T0E _58 Vehicle Interior _053737 SEAT _0261105 REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


NOTICE:
·

Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).

-

The fold seat control ECU is replaced with a new one.

-

Initialization (initial position reset) of the fold seat control ECU is performed.



·

Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).

-

The fold seat control ECU is exchanged with one from another vehicle.

-

The seatback frame and seat leg are inspected.

-

The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.

-

The seatback frame or seat leg is replaced.

-

The cable is disconnected from the battery while the seatback or seat cushion is operating.




HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 79040 1.INSTALL NO. 3 SEAT LEG ASSEMBLY LH

a.

Install the seat cushion under carpet LH to the No. 3 seat leg assembly LH with 4 new clips.


Hide 79020B 2.INSTALL NO. 2 SEAT LEG ASSEMBLY (for RH Side)

a.

Install the seat cushion under carpet RH to the No. 2 seat leg assembly with 4 new clips.


Hide 82196 3.INSTALL REAR NO. 2 SEAT WIRE LH

a.

Attach the wire harness claw and clamp to install the No. 2 seat wire LH.


b.

Connect the connector.


c.

install the warning reflector holder.


Hide 79304A 4.INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH

a.

Using a T45 "TORX" socket wrench, install the No. 3 seatback frame sub-assembly LH with the 4 "TORX" bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 72695C 5.INSTALL REAR SEAT LOCK CONTROL CABLE LH

a.
B238712C03
1.771,2 0.667,2 true 0.927,1.083 0.927,2 true 2.865,1.531 2.469,1.531 true 0.625,0.969 1.01,0.573 1.01,0.573 1.115,0.573 true 0.458,1.917 0.615,2.063 0.156,0.146 10 false *b 2.281,1.438 2.438,1.583 0.156,0.146 10 true *a 1.125,0.5 1.635,1.01 0.51,0.51 10 false *a
*a Cable End
*b Clamp


Twist the 2 cable ends in the direction indicated by the arrow to connect them.


b.

Attach the 2 clamps to install the rear seat lock control cable LH.

HINT:
B505967

Install at the middle level of the cable clamp (triple level) side.



Hide 72695B 6.INSTALL REAR SEAT LOCK CONTROL CABLE RH (for RH Side)

a.
B238711C02
2.74,0.896 2.479,0.896 true 2.25,0.896 0.99,0.896 true 2.042,1.219 0.333,1.219 true 1.615,0.469 0.458,0.469 0.458,0.469 0.458,1.208 true 0.521,2.313 0.521,1.229 true 1.854,2.896 1.667,2.625 1.667,2.625 1.552,2.625 true 1.792,1.313 1.438,1.313 true 2.281,0.792 2.427,0.948 0.146,0.156 10 false *a 0.146,1.135 0.292,1.292 0.146,0.156 10 false *b 1.375,2.542 1.542,2.719 0.167,0.177 10 true *c 1.26,1.24 1.417,1.427 0.156,0.188 10 false *c
*a Cable Tie
*b Clamp
*c Cable End


Twist the 2 cable ends in the direction indicated by the arrow to connect them.


b.

Attach the 3 clamps to install the rear seat lock control cable RH.

HINT:
B505967

Install at the middle level of the cable clamp (triple level) side.



c.

Install 2 new cable ties.


Hide 72690A 7.INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY LH

a.
B238710C04
1.24,2.51 2.521,2.51 true 2.156,1.948 2.156,2.51 true 0.906,2.406 1.333,2.083 1.333,2.083 1.427,2.083 true 2.542,2.427 2.698,2.573 0.156,0.146 10 false *b 1.448,2.01 1.604,2.156 0.156,0.146 10 false *a
*a Cable End
*b Clamp


Twist the cable end in the direction indicated by the arrow to connect it.


b.

Attach the 2 clamps to install the rear seat lock release strap assembly LH.


Hide 72690A 8.INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY RH (for RH Side)

a.
B238709C02
1.5,2.104 2.615,1.958 true 2.25,2.01 2.25,2.125 false 1.896,2.333 0.323,2.333 true 1.823,1.385 0.344,1.385 0.344,1.385 0.344,2.323 true 0.49,1.885 0.333,1.885 true 1.646,2.438 1.219,2.438 true 2.156,2.125 2.313,2.26 0.156,0.135 10 false *a 0.125,2.26 0.292,2.438 0.167,0.177 10 false *b 1.052,2.365 1.219,2.531 0.167,0.167 10 false *c
*a Cable Tie
*b Clamp
*c Cable End


Twist the cable end in the direction indicated by the arrow to connect it.


b.

Attach the 3 clamps to install the rear seat lock release strap assembly RH.


c.

Install the 2 new cable ties.


Hide 71844A 9.INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER LH

a.

Attach the 2 claws and guide to install the rear No. 2 seat outer reclining cover LH.


b.

Install the screw.


Hide 71844C 10.INSTALL REAR NO. 2 SEAT INNER RECLINING COVER LH

a.

Attach the 5 claws to install the rear No. 2 seat inner reclining cover LH.


Hide 72906 11.INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH

a.

Attach the 4 guides and 2 claws to install the 3rd seat link sub-assembly LH.


b.

Install 3 new clips.


Hide 73590 12.INSTALL REAR NO.2 SEAT INNER BELT ASSEMBLY LH

Hide 79384 13.INSTALL REAR SEAT LEG COVER LH

a.

Attach the 5 clips and 3 hooks to install the rear seat leg cover LH.


b.

Install a new clip.


Hide 79202 14.INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH

a.

Using a T40 "TORX" socket wrench, install the No. 2 seat cushion frame sub-assembly LH with the 4 "TORX" bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Pull out the No. 2 seat cushion frame sub-assembly LH.


c.

Connect the wire harness with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 71834C 15.INSTALL REAR NO. 3 SEAT OUTER RECLINING COVER LH

a.

Attach the 2 claws and guide to install the rear No. 3 seat outer reclining cover LH.


b.

Install the screw.


Hide 71834C 16.INSTALL REAR NO. 3 SEAT INNER RECLINING COVER LH

a.

Attach the 4 claws to install the rear No. 3 seat inner reclining cover LH.


Hide 71587C 17.INSTALL REAR SEATBACK EDGE PROTECTOR

a.

Attach the 4 claws to install the 2 rear seatback edge protectors.


Hide 71970 18.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the rear seat headrest assembly with the 3 nuts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 71987A 19.INSTALL REAR SEAT HEADREST CABLE

a.
B238713C05
0.646,1.771 1.229,1.615 1.229,1.615 0.646,1.448 true 2.854,1.219 2.74,1.219 2.74,1.219 2.656,0.99 true 0.531,1.948 0.333,1.896 0.333,1.896 0.24,1.896 true 1.271,1.51 1.448,1.688 0.177,0.177 10 false *b 2.875,1.125 3.063,1.281 0.188,0.156 10 false *a 0.052,1.813 0.219,1.958 0.167,0.146 10 false *a
*a Cable End
*b Clamp


Twist the 2 cable ends in the direction indicated by the arrow to install them.


b.

Attach the 2 clamps to install the rear seat headrest cable.


Hide 71970A 20.INSTALL REAR SEAT HEADREST COVER

a.

Attach the 2 claws and guide to install the rear seat headrest cover.


b.

Install the 2 screws.


Hide 79962 21.INSTALL NO. 2 SEATBACK COVER

a.

Attach the 2 claws to install the No. 2 seatback cover.


Hide 71587C 22.INSTALL REAR NO. 2 SEATBACK EDGE PROTECTOR

a.

Install the rear No. 2 seatback edge protector to the seatback pad with 5 new tack pins.


Hide 79034 23.INSTALL NO. 3 SEATBACK COVER SUB-ASSEMBLY LH

a.

Using hog ring pliers, install the No. 3 seatback cover sub-assembly LH to the seatback pad with 7 new hog rings.

B449836C01
1.948,1.698 2.333,0.698 2.333,0.698 2.49,0.698 false 2.5,0.594 2.813,0.792 0.313,0.198 10 false *a
*a Hog Ring Pliers - -


NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 24.INSTALL SEATBACK COVER WITH PAD

a.

Attach the 8 clips.


b.

Using hog ring pliers, install the 2 new hog rings.


c.

Attach the 6 hooks to install the seatback cover with pad.


Hide 71865 25.INSTALL REAR SEAT NO. 1 COVER BEZEL

a.

Pass the strap through the bezel hole.


b.

Attach the guide to install the rear seat No. 1 cover bezel.


c.

Install the 2 screws.


Hide 72635B 26.INSTALL REAR SEATBACK LOCK HOOK

a.

Install the rear seatback lock hook.


Hide 71702C 27.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH

a.

w/ Seatback Rail:

i.
B238695N01
2.417,1.083 2.615,1.302 0.198,0.219 10 false (1) 0.896,1.01 1.094,1.229 0.198,0.219 10 false (2) 1.865,1.052 2.063,1.271 0.198,0.219 10 false (3) 2.563,1.771 2.76,1.99 0.198,0.219 10 false (3) 1.094,1.573 1.292,1.792 0.198,0.219 10 false (3) 1.167,2.24 1.365,2.458 0.198,0.219 10 false (3) 2.479,2.26 2.677,2.479 0.198,0.219 10 false (3)

Attach the 7 clips in the order as shown in the illustration to install the rear seatback board sub-assembly LH.



b.

w/ Seatback Hook:

i.
B511114N01
2.417,1.083 2.875,1.281 0.458,0.198 10 false (1) 0.875,1.083 1.333,1.281 0.458,0.198 10 false (2) 1.76,1.094 2.219,1.292 0.458,0.198 10 false (3) 2.521,1.76 2.979,1.958 0.458,0.198 10 false (3) 1,1.583 1.458,1.781 0.458,0.198 10 false (3) 1.125,2.24 1.583,2.438 0.458,0.198 10 false (3) 2.406,2.26 2.865,2.458 0.458,0.198 10 false (3)

Attach the 7 clips in the order as shown in the illustration to install the rear seatback board sub-assembly LH.



Hide 66310F 28.INSTALL ROPE HOOK ASSEMBLY (w/ Seatback Hook)

a.

Install the rope hook assembly with the bolt.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Attach the 2 claws to close the cover.


Hide 72152 29.INSTALL LOWER SEAT TRACK RAIL LH (w/ Seatback Rail)

a.

Install the lower seat track rail LH with the 2 bolts.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 71694E 30.INSTALL REAR SEAT CUSHION INNER HINGE COVER RH

a.

Attach the guide to install the rear seat cushion inner hinge cover RH.


b.

Install the screw and a new clip.


Hide 71694E 31.INSTALL REAR SEAT CUSHION INNER HINGE COVER LH

a.

Attach the guide to install the rear seat cushion inner hinge cover LH.


b.

Install the screw and a new clip.


Hide 79384A 32.INSTALL REAR NO. 3 SEAT LEG COVER LH

a.

Attach the 2 claws to install the rear No. 3 seat leg cover LH.


Hide 71827B 33.INSTALL REAR SEAT NO. 2 CUSHION MOULDING

a.

Attach the 2 claws to install the rear seat No. 2 cushion moulding.


b.

Install the 2 screws.


Hide 71647F 34.INSTALL REAR SEAT CUSHION INNER EDGE PROTECTOR LH

a.

Install the rear seat cushion inner edge protector LH to the seat cushion pad with 5 new tack pins.


Hide 79032 35.INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH

a.
B238853C06
2.021,2.875 1.75,2.875 1.75,2.875 1.854,3.698 false 2.115,1.302 2.115,2.104 2.115,2.104 2.615,2.104 true 2.625,2.021 2.792,2.167 0.167,0.146 10 false *a 2.042,2.792 2.208,2.938 0.167,0.146 10 false *b
*a Fastener
*b Hog Ring Pliers


Using hog ring pliers, install the No. 3 seat cushion cover sub-assembly to the seat cushion pad with 2 new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.

Attach the fastener.


Hide 36.INSTALL SEAT CUSHION COVER WITH PAD

a.

Attach the 2 hooks to install the seat cushion cover with pad.


b.

Close the under part of the seat cushion coveri and install 2 new clips.


c.

Close the 2 fasteners.


Hide 71827B 37.INSTALL REAR SEAT NO. 1 CUSHION MOULDING

a.

Attach the 4 guides and 2 claws to install the rear seat No. 1 cushion moulding.


b.

Install 2 new clips.


Hide 71693 39.INSTALL REAR SEAT CUSHION LOWER HINGE COVER RH

a.

Attach the 2 claws to install the rear seat cushion lower hinge cover RH.


b.

Install the 2 screws.


Hide 71693 40.INSTALL REAR SEAT CUSHION LOWER HINGE COVER LH

a.

Attach the guide and 2 claws to install the rear seat cushion lower hinge cover LH.


b.

Install the 2 screws.


Hide 73949 41.INSTALL CAP

a.

Install the 2 caps.