Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2021.06
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) D

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  DIAGNOSIS SYSTEM  


CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION


a.

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Connected to Code ECU/Sensor Name GTS Display Applicability
- CGW Central gateway ECU (network gateway ECU) - Installed on all vehicles
V Bus DLC3 DLC3 - Installed on all vehicles
Bus 2 ENG ECM ECM (Engine) Installed on all vehicles
A/C Air conditioning amplifier assembly Air Conditioning Amplifier Installed on all vehicles
SMT Certification ECU (smart key ECU assembly) Certification (Smart) w/ Entry and Start System
PPS Power steering ECU assembly PPS Installed on all vehicles
BRK Master cylinder solenoid (skid control ECU) Skid Control (ABS/VSC/TRAC) except 2TR-FE
Brake actuator assembly (skid control ECU) Skid Control (ABS/VSC/TRAC) for 2TR-FE
SRS Airbag sensor assembly Airbag Installed on all vehicles
STR Steering sensor Spiral Cable (Steering Angle Sensor) Installed on all vehicles
MET Combination meter assembly Combination Meter Installed on all vehicles
TPMS Tire pressure warning ECU and receiver Tire Pressure w/ Tire Pressure Warning System
LIT No. 1 headlight ECU sub-assembly LH Headlight swivel (AFS) for LED Headlight
S&S Engine stop and start ECU Stop and Go/Start w/ Stop and Start System
MB Main body ECU (multiplex network body ECU) Main Body Installed on all vehicles
Bus 3 AV Radio and display receiver assembly (EMVN ECU) Display and Navigation (AVN) w/ Audio and Visual System (for Radio and Display Type), w/ Navigation System
DCM Telephone transceiver assembly DCM w/ Telematics System
Bus 5 PAC Parking assist ECU Panoramic View Monitor / Circumference Monitoring Camera Control Module w/ Multi-terrain Monitor System
CS Clearance warning ECU assembly Clearance Warning (Clearance Sonar) w/ TOYOTA Parking Assist-sensor System (w/ Multi-display)
SBF Stabilizer control ECU Stabilizer Control (KDSS) w/ Kinetic Dynamic Suspension System
F-CAM Forward recognition camera Front Camera Module w/ Pre-collision System
BSM Blind spot monitor sensor LH Blind Spot Monitor Master w/ Blind Spot Monitor System
F-MR Millimeter wave radar sensor assembly Front Radar w/ Pre-collision System
AWD 4 wheel drive control ECU (4WD control ECU) Four Wheel Drive Control Installed on all vehicles
SUS Suspension control ECU Suspension Control (Air Suspension) w/ Air Suspension System
Sub Bus 1 MB Main body ECU (multiplex network body ECU) - Installed on all vehicles
DST Front power seat switch (power seat control ECU) D-Seat w/ Seat Memory
DFL Outer mirror control ECU assembly LH Front Door LH/L-Mirror (FL-Door2/L-Mirror) w/ Reverse Shift-linked Mirror
DFR Outer mirror control ECU assembly RH Front Door RH/R-Mirror (FR-Door2/R-Mirror) w/ Reverse Shift-linked Mirror
T&T Multiplex tilt and telescopic ECU Multiplex Tilt and Telescopic for Power Tilt and Power Telescopic Steering Column



CAN BUS CHECK


HINT:

The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.


a.

Using the GTS, select the CAN Bus Check screen.

NOTICE:
·

It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)

·

In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>SYSTEM DIAGRAM



HINT:

Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.


Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
Bus White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4

·

No ECUs or sensors are connected to the bus.*5


Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU).*6

·

No ECUs or sensors are connected to the sub bus.*7



·

Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.

·

*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.

·

*2: The gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.

·

*3: The gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.

·

*4: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.

·

*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.

·

If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU (network gateway ECU) and V bus (the bus that connects the DLC3 to the central gateway ECU (network gateway ECU)) for malfunctions.



b.

Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.

HINT:
·

If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.

·

If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.





HOW TO INTERPRET CAN BUS CHECK SCREEN


a.

When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.

NOTICE:

The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.


HINT:
·

When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.

·

Wait for approximately 2 minutes after turning the ignition switch to ON (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.




b.

If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.

Example: Open in both CAN branch lines of HV on the bus 4

C360877C01
6.292,6.135 6.604,6.333 0.313,0.198 10 false *f 1,1.115 1.313,1.313 0.313,0.198 10 false *a 1.01,2.292 1.323,2.49 0.313,0.198 10 false *b 1.708,3.542 2.021,3.74 0.313,0.198 10 false *c 5.479,0.625 5.792,0.823 0.313,0.198 10 false : *e 1.021,4.438 1.333,4.635 0.313,0.198 10 false *d 0.448,2.542 1.292,2.781 0.844,0.24 10 false CGW 2.063,0.719 2.906,0.958 0.844,0.24 10 false F-MGC 3.75,0.719 4.594,0.958 0.844,0.24 10 false HVB 4.302,0.719 5.146,0.958 0.844,0.24 10 false R-MGC 1.948,1.302 2.792,1.542 0.844,0.24 10 false CAN J/C 1 3.865,1.302 4.708,1.542 0.844,0.24 10 false CAN J/C 2 6.406,1.302 6.906,1.542 0.5,0.24 10 false ENG 1.865,1.885 2.708,2.125 0.844,0.24 10 false HV 2.438,1.875 3.281,2.115 0.844,0.24 10 false BRK 1.958,2.469 2.802,2.708 0.844,0.24 10 false CAN J/C 3 3.896,2.469 4.74,2.708 0.844,0.24 10 false CAN J/C 4 5.719,2.469 6.219,2.698 0.5,0.229 10 false SRS 1.844,3.125 2.344,3.354 0.5,0.229 10 false MB 3.76,3.073 4.26,3.302 0.5,0.229 10 false EPS 4.385,3.073 4.885,3.302 0.5,0.229 10 false STR 2.917,3.906 3.76,4.146 0.844,0.24 10 false CAN J/C 5 4.813,3.906 5.656,4.146 0.844,0.24 10 false CAN J/C 6 6.458,3.906 6.771,4.146 0.313,0.24 10 false ST 1.531,4.573 2.031,4.802 0.5,0.229 10 false DLC3 3.052,4.51 3.552,4.74 0.5,0.229 10 false MIR-R 4.979,4.51 5.479,4.74 0.5,0.229 10 false MIR-L
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Background color is red


HINT:

When there are communication stops, ECUs that are present in the vehicle may not be displayed on the CAN Bus Check screen.



c.

If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or sensor whose background color is red) is suspected.

Example: Open in a CAN branch line for HV on the bus 4

C360878C01
6.365,1.135 6.677,1.333 0.313,0.198 10 false *a 6.354,1.625 6.667,1.823 0.313,0.198 10 false *c 0.708,1.771 1.021,1.969 0.313,0.198 10 false *c 0.708,1.198 1.021,1.396 0.313,0.198 10 false *b
*a Background color is red *b Background color intermittently becomes yellow or red
*c Not displayed or background color is yellow or red - -


Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
Bus White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4

·

No ECUs or sensors are connected to the bus.*5


Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*6

·

No ECUs or sensors are connected to the sub bus.*7



·

Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.

·

*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.

·

*2: The gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.

·

*3: The gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.

·

*4: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.

·

*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.

·

The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of HV is also unstable. In addition, in this example, MB is equipped with a gateway function. Therefore, communication is also unstable between the Sub bus ECUs of MB and the bus 4.

·

The example in the illustration shows that HV has a red background color on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of HV is suspected.



d.

If a communication error is indicated on both the bus 4 and Sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the bus 4 first.

Example: Open in both CAN branch lines of MB on the bus 4

C360879C01
0.708,1.292 1.021,1.448 0.313,0.156 10 false *a 0.708,1.781 1.021,1.938 0.313,0.156 10 false *b 6.344,1.635 6.656,1.792 0.313,0.156 10 false *b
*a Background color is red *b Not displayed


HINT:
·

In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the bus after connecting the GTS to the DLC3. As for sub bus, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the bus.

·

If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.

·

The CAN Bus Check screen in the illustration shows that MB has a gateway function and a communication stop in MB is suspected.




e.

If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.

Example: Open in both CAN branch lines of MIR-R on the sub bus

C360880C01
6.354,1.615 6.667,1.771 0.313,0.156 10 false *a
*a Background color is red - -


HINT:
·

A communication error in a sub bus does not affect the other buses.

·

When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)




f.

If both of the bus 2 main bus lines are open, ECUs or sensors that are located farther away from the central gateway ECU (network gateway ECU) than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, HVB, R-MGC and ENG background color changes to red.)

C360881C01
6.344,5.896 6.656,6.094 0.313,0.198 10 false *f 0.75,5.969 1.063,6.167 0.313,0.198 10 false *f 0.417,2.667 0.875,2.865 0.458,0.198 10 false CGW 1.031,1.125 1.281,1.292 0.25,0.167 10 false *a 1.021,2.302 1.271,2.469 0.25,0.167 10 false *b 1.021,4.469 1.271,4.635 0.25,0.167 10 false *d 1.698,3.521 1.948,3.688 0.25,0.167 10 false *c 2.073,0.719 2.656,0.917 0.583,0.198 10 false F-MGC 1.927,1.292 2.76,1.49 0.833,0.198 10 false CAN J/C 1 1.854,1.885 2.188,2.083 0.333,0.198 10 false HV 2.458,1.865 2.875,2.031 0.417,0.167 10 false BRK 1.854,3.135 2.271,3.302 0.417,0.167 10 false MB 1.958,2.458 2.792,2.656 0.833,0.198 10 false CAN J/C 3 2.917,3.896 3.75,4.094 0.833,0.198 10 false CAN J/C 5 4.833,3.906 5.667,4.104 0.833,0.198 10 false CAN J/C 6 3.875,2.448 4.708,2.646 0.833,0.198 10 false CAN J/C 4 3.76,0.719 4.344,0.917 0.583,0.198 10 false HVB 4.313,0.719 4.896,0.917 0.583,0.198 10 false R-MGC 6.427,1.302 6.833,1.5 0.406,0.198 10 false ENG 3.875,1.281 4.708,1.479 0.833,0.198 10 false CAN J/C 2 3.74,3.073 4.167,3.25 0.427,0.177 10 false EPS 4.406,3.073 4.74,3.24 0.333,0.167 10 false STR 5.74,2.458 6.083,2.667 0.344,0.208 10 false SRS 6.469,3.896 6.75,4.083 0.281,0.188 10 false ST 5,4.531 5.5,4.781 0.5,0.25 10 false MIR-L 3.052,4.531 3.552,4.781 0.5,0.25 10 false MIR-R 1.521,4.573 2.021,4.823 0.5,0.25 10 false DLC3 5.479,0.635 6.094,0.833 0.615,0.198 10 false : *e
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Background color is red


HINT:

If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.



g.

If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, MIR-L background color changes to red.)

C360882C01
1.031,1.146 1.344,1.302 0.313,0.156 10 false *a 1.031,2.313 1.344,2.469 0.313,0.156 10 false *b 1.708,3.552 2.021,3.708 0.313,0.156 10 false *c 1.021,4.458 1.333,4.615 0.313,0.156 10 false *d 5.5,0.625 5.896,0.792 0.396,0.167 10 false : *e 0.75,6.771 1.063,6.927 0.313,0.156 10 false *f 0.438,2.698 0.896,2.896 0.458,0.198 10 false CGW 2.063,0.74 2.646,0.99 0.583,0.25 10 false F-MGC 1.948,1.281 2.948,1.448 1,0.167 10 false CAN J/C 1 3.875,1.281 4.875,1.448 1,0.167 10 false CAN J/C 2 4.802,3.896 5.802,4.063 1,0.167 10 false CAN J/C 6 2.885,3.896 3.885,4.063 1,0.167 10 false CAN J/C 5 3.75,0.729 4.333,0.979 0.583,0.25 10 false HVB 4.323,0.74 4.906,0.99 0.583,0.25 10 false R-MGC 6.406,1.292 6.823,1.542 0.417,0.25 10 false ENG 5.74,2.458 6.156,2.708 0.417,0.25 10 false SRS 1.865,1.885 2.281,2.135 0.417,0.25 10 false HV 2.469,1.885 2.885,2.135 0.417,0.25 10 false BRK 1.958,2.458 2.958,2.625 1,0.167 10 false CAN J/C 3 3.875,2.448 4.875,2.615 1,0.167 10 false CAN J/C 4 1.854,3.146 2.188,3.396 0.333,0.25 10 false MB 3.75,3.073 4.167,3.323 0.417,0.25 10 false EPS 4.396,3.073 4.813,3.323 0.417,0.25 10 false STR 1.521,4.573 1.938,4.823 0.417,0.25 10 false DLC3 3.063,4.51 3.563,4.76 0.5,0.25 10 false MIR-R 4.969,4.51 5.469,4.76 0.5,0.25 10 false MIR-L 6.469,3.917 6.802,4.167 0.333,0.25 10 false ST
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Background color is red



h.

When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.

Details of Malfunction
Short between CAN lines (CANH and CANL)
Short between a CAN line (CANH or CANL) and +B
Short between a CAN line (CANH or CANL) and ground
Open in a CAN main bus line

C360883C01
0.604,0.198 0.917,0.354 0.313,0.156 10 false *a 0.625,1.938 0.938,2.094 0.313,0.156 10 false *b 0.719,1.031 1.031,1.188 0.313,0.156 10 false *c 0.719,1.448 1.031,1.604 0.313,0.156 10 false *d 6.354,1.281 6.667,1.438 0.313,0.156 10 false *d 6.344,0.948 6.656,1.104 0.313,0.156 10 false *c 6.354,2.99 6.667,3.146 0.313,0.156 10 false *d 0.698,3.146 1.01,3.302 0.313,0.156 10 false *d
*a When any of the following malfunctions occur on the bus 4 *b When any of the following malfunctions occur on a sub bus
*c Background color is red *d Not displayed


HINT:
·

When a malfunction occurs in the bus, almost all ECUs and sensors on the bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).

·

When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.

·

A communication error in a sub bus does not affect the other buses.

·

The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.




i.

If a communication error of all ECUs and sensors is indicated on the CAN Bus Check screen, a communication stop of the V bus (DLC3 - central gateway ECU (network gateway ECU)) is suspected.

Open in both CAN branch lines in the V bus

C360884C01
1.031,1.146 1.344,1.302 0.313,0.156 10 false *a 1.031,2.313 1.344,2.469 0.313,0.156 10 false *b 1.698,3.531 2.01,3.688 0.313,0.156 10 false *c 1.021,4.385 1.333,4.542 0.313,0.156 10 false *d 5.5,0.635 6,0.875 0.5,0.24 10 false : *e 0.719,6.219 0.969,6.385 0.25,0.167 10 false *f 6.385,6.135 6.635,6.302 0.25,0.167 10 false *f 0.448,2.667 0.948,2.833 0.5,0.167 10 false CGW 2.063,0.719 2.646,0.885 0.583,0.167 10 false F-MGC 1.948,1.302 2.865,1.469 0.917,0.167 10 false CAN J/C 1 3.844,1.292 4.76,1.458 0.917,0.167 10 false CAN J/C 2 1.927,2.469 2.844,2.635 0.917,0.167 10 false CAN J/C 3 3.833,2.479 4.75,2.646 0.917,0.167 10 false CAN J/C 4 2.917,3.906 3.833,4.073 0.917,0.167 10 false CAN J/C 5 4.813,3.906 5.729,4.073 0.917,0.167 10 false CAN J/C 6 3.75,0.719 4.167,0.885 0.417,0.167 10 false HVB 4.313,0.729 4.979,0.896 0.667,0.167 10 false R-MGC 6.417,1.313 6.917,1.563 0.5,0.25 10 false ENG 5.729,2.479 6.229,2.729 0.5,0.25 10 false SRS 6.469,3.917 6.969,4.167 0.5,0.25 10 false ST 4.99,4.51 5.49,4.76 0.5,0.25 10 false MIR-L 3.063,4.531 3.563,4.781 0.5,0.25 10 false MIR-R 1.521,4.573 2.021,4.823 0.5,0.25 10 false DLC3 1.854,3.146 2.354,3.396 0.5,0.25 10 false MB 3.75,3.094 4.083,3.344 0.333,0.25 10 false EPS 4.385,3.094 4.719,3.344 0.333,0.25 10 false STR 1.865,1.906 2.198,2.156 0.333,0.25 10 false HV 2.469,1.896 2.885,2.146 0.417,0.25 10 false BRK
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Not displayed


HINT:

When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.




DTC TABLE BY ECU


HINT:
·

In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.

·

If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If there is a malfunction currently, DTCs can be checked by performing steps in the DTC check procedure.



a.

ECM

i.

GTS Display "Engine and ECT" (except 1GD-FTV)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0129 Lost Communication with Brake System Control Module Either of the following conditions is met:
·

Communication stop occurs between the ECM and skid control ECU for approximately 3 seconds or more.

·

Communication stop occurs between the ECM and skid control ECU for approximately 13 seconds or more.


All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the ECM is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 16 seconds. - - DTC is stored until it is cleared using the GTS.


ii.

GTS Display "Engine and ECT" (for 1GD-FTV)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to ECD System (for 1GD-FTV with Urea SCR System)

Click here(Click here)

U012987 Lost Communication with Brake System Control Module Either of the following conditions is met:
·

Communication stop occurs between the ECM and skid control ECU for approximately 3 seconds or more.

·

Communication stop occurs between the ECM and skid control ECU for approximately 13 seconds or more.


All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the ECM is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 16 seconds. - - DTC is stored until it is cleared using the GTS.
U010E87* Lost Communication with Reductant Control Module Communication stop occurs between the ECM and urea pump control ECU continuously for approximately 2 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the ECM is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. MIL (malfunction indicator lamp) illuminates. - DTC is stored until it is cleared using the GTS.
U029D87* Lost Communication with NOx Sensor "A" Communication stop occurs between the ECM and nitrogen oxides sensor continuously for approximately 2 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the ECM is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. MIL (malfunction indicator lamp) illuminates. - DTC is stored until it is cleared using the GTS.
U029E87* Lost Communication with NOx Sensor "B" Communication stop occurs between the ECM and nitrogen oxides sensor continuously for approximately 2 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the ECM is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. MIL (malfunction indicator lamp) illuminates. - DTC is stored until it is cleared using the GTS.
U02A387* Lost Communication with PM Sensor Communication stops between the ECM and the particulate matter sensor for approximately 2 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the ECM is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. MIL (malfunction indicator lamp) illuminates. - DTC is stored until it is cleared using the GTS.
U110387 Lost Communication with Stop and Start Control Module Missing Message Communication stop occurs between the ECM and the engine and stop and start ECU continuously for approximately 2 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the ECM is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 3 seconds. MIL (malfunction indicator lamp) illuminates. - DTC is stored until it is cleared using the GTS.


iii.

GTS Display "Cruise Control" (w/ Cruise Control System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0122 Lost Communication with Vehicle Dynamics Control Module The ECM does not receive data from the skid control ECU for approximately 3 seconds All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The cruise control switch is on

·

The ECM power supply voltage is 10.5 V or higher.


Allow the cruise control system to operate for approximately 4 seconds or more. The cruise control main indicator illuminates in yellow. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


iv.

GTS Display "ECT"

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication With ECM/PCM "A" The ECM is unable to receive certain data from the skid control ECU for 1 second or more. All conditions are met:
·

The ignition switch is ON.

·

The radar cruise control system (vehicle control mode) is operating.


Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


v.

GTS Display "Radar Cruise1" (except 1GD-FTV with Pre-collision System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication With ECM/PCM "A" The ECM is unable to receive certain data from the skid control ECU for 1 second or more. All conditions are met:
·

The ignition switch is ON.

·

The radar cruise control system (vehicle control mode) is operating.


Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0104 Lost Communication with Driving Support ECU The driving support ECU assembly data sent to the ECM, skid control ECU or millimeter wave radar sensor assembly is lost for 1 second or more. All conditions are met:
·

The ignition switch is ON.

·

The radar cruise control system (vehicle control mode) is operating.


Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0122 Lost Communication with Vehicle Dynamics Control Module When the vehicle speed is 50 km/h (31 mph) or more and is being controlled by the cruise control system in vehicle-to-vehicle distance control mode, the ECM does not receive data from the skid control ECU for approximately 3 seconds or more. All conditions are met:
·

The ignition switch is ON.

·

The radar cruise control system (vehicle control mode) is operating.


Allow the radar cruise control system (vehicle control mode) to operate for approximately 3 seconds or more - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


vi.

GTS Display "Radar Cruise1" (for 1GD-FTV with Pre-collision System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010087 Lost Communication With ECM/PCM "A" The ECM is unable to receive certain data from the skid control ECU for 1 second or more. All conditions are met:
·

The ignition switch is ON.

·

The radar cruise control system (vehicle control mode) is operating.


Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012287 Lost Communication with Vehicle Dynamics Control Module The ECM is unable to receive certain data from the skid control ECU for approximately 3 seconds or more. All conditions are met:
·

The ignition switch is ON.

·

The radar cruise control system (vehicle control mode) is operating.


Allow the radar cruise control system (vehicle control mode) to operate for approximately 4 seconds or more - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U010487 Lost Communication with Driving Support ECU The driving support ECU assembly data sent to the ECM, skid control ECU or millimeter wave radar sensor assembly is lost for 1 second or more. All conditions are met:
·

The ignition switch is ON.

·

The radar cruise control system (vehicle control mode) is operating.


Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.



b.

Brake Actuator Assembly (Skid Control ECU) / GTS Display "ABS/VSC/TRC" (for 2TR-FE without Pre-collision System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0073 Control Module Communication Bus OFF Either of the following conditions is met:
·

The response sent to the skid control ECU from the steering sensor is invalid for 1 second or more.

·

The response sent to the skid control ECU from the airbag sensor assembly is invalid for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds:

-

The response sent to the skid control ECU from the airbag sensor assembly is invalid at least once within 5 seconds.

-

The response sent to the skid control ECU from the steering sensor is invalid at least once within 5 seconds.


·

The skid control ECU cannot send or receive data (the bus is off) 10 times consecutively.


All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least approximately 60 seconds.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0100 Lost Communication with ECM / PCM Communication stop occurs between the skid control ECU and ECM continuously for 2 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The vehicle speed is 15 km/h (9 mph) or more.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Drive the vehicle for 3 seconds or more at a speed of 15 km/h (9 mph) or more. Slip indicator light illuminates. - DTC is stored until it is cleared using the GTS.
U0114 Lost Communication with Four-Wheel Drive Clutch Control Module Communication stop occurs between the skid control ECU and 4 wheel drive control ECU (4WD control ECU) continuously for approximately 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least approximately 2 seconds.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS or the ignition switch off.
U0123 Lost Communication with Yaw Rate Sensor Module Either of the following conditions is met:
·

Communication stop occurs between the skid control ECU and airbag sensor assembly (yaw rate sensor) continuously for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds:

-

The response sent to the skid control ECU from the airbag sensor assembly (yaw rate sensor) is invalid at least once within 5 seconds.



All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least approximately 60 seconds. Slip indicator light illuminates. - DTC is stored until it is cleared using the GTS or the ignition switch off.
U0124 Lost Communication with Lateral Acceleration Sensor Module Either of the following conditions is met:
·

Communication stop occurs between the skid control ECU and airbag sensor assembly (acceleration sensor) continuously for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds:

-

The response sent to the skid control ECU from the airbag sensor assembly (acceleration sensor) is invalid at least once within 5 seconds.



All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least approximately 60 seconds.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Either of the following conditions is met:
·

Communication stop occurs between the skid control ECU and steering sensor continuously for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds:

-

The response sent to the skid control ECU from the steering sensor is invalid at least once within 5 seconds.



All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least approximately 60 seconds. Slip indicator light illuminates. - DTC is stored until it is cleared using the GTS.


c.

Master Cylinder Solenoid (Skid Control ECU) / GTS Display "ABS/VSC/TRC" (except 2TR-FE, for 2TR-FE with Pre-collision System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0073 Control Module Communication Bus OFF Either of the following conditions is met:
·

The response sent to the skid control ECU from the steering sensor is invalid for 1 second or more.

·

The response sent to the skid control ECU from the airbag sensor assembly is invalid for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds:

-

The response sent to the skid control ECU from the airbag sensor assembly is invalid at least once within 5 seconds.

-

The response sent to the skid control ECU from the steering sensor is invalid at least once within 5 seconds.


·

The skid control ECU cannot send or receive data (the bus is off) 10 times consecutively.


All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least approximately 60 seconds.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0100 Lost Communication with ECM / PCM Communication stop occurs between the skid control ECU and ECM continuously for 2 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The vehicle speed is 15 km/h (9 mph) or more.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Drive the vehicle for 3 seconds or more at a speed of 15 km/h (9 mph) or more. Slip indicator light illuminates. - DTC is stored until it is cleared using the GTS.
U0114 Lost Communication with Four-Wheel Drive Clutch Control Module Communication stop occurs between the skid control ECU and 4 wheel drive control ECU (4WD control ECU) continuously for approximately 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least approximately 2 seconds.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS or the ignition switch off.
U0123 Lost Communication with Yaw Rate Sensor Module Either of the following conditions is met:
·

Communication stop occurs between the skid control ECU and airbag sensor assembly (yaw rate sensor) continuously for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds:

-

The response sent to the skid control ECU from the airbag sensor assembly (yaw rate sensor) is invalid at least once within 5 seconds.



All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least approximately 60 seconds. Slip indicator light illuminates. - DTC is stored until it is cleared using the GTS or the ignition switch off.
U0124 Lost Communication with Lateral Acceleration Sensor Module Either of the following conditions is met:
·

Communication stop occurs between the skid control ECU and airbag sensor assembly (acceleration sensor) continuously for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds:

-

The response sent to the skid control ECU from the airbag sensor assembly (acceleration sensor) is invalid at least once within 5 seconds.



All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least approximately 60 seconds.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Either of the following conditions is met:
·

Communication stop occurs between the skid control ECU and steering sensor continuously for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds:

-

The response sent to the skid control ECU from the steering sensor is invalid at least once within 5 seconds.



All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the skid control ECU is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least approximately 60 seconds. Slip indicator light illuminates. - DTC is stored until it is cleared using the GTS.


d.

Combination Meter Assembly / GTS Display "Combination Meter"

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM / PCM "A" Communication stop occurs between the combination meter assembly and ECM continuously for 2 seconds or more. All conditions are met:
·

The ignition switch is ON.

·

The power source voltage of the combination meter assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. MIL (malfunction indicator lamp) illuminates. - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Either of the following conditions is met:
·

Communication stop occurs between the combination meter assembly and skid control ECU continuously for 2 seconds or more.

·

Communication stop occurs between the combination meter assembly and skid control ECU continuously for 3 seconds or more.


All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the combination meter assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0131 Lost Communication with Power Steering Control Module Communication stop occurs between the combination meter assembly and power steering ECU assembly continuously for 3 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the combination meter assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. PPS warning light illuminates. - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the combination meter assembly and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the combination meter assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - - DTC is stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module Communication stop occurs between the combination meter assembly and airbag sensor assembly continuously for 10 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the combination meter assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. SRS warning light illuminates. - DTC is stored until it is cleared using the GTS.
U0163 Lost Communication with Navigation Control Module Communication stop occurs between the combination meter assembly and the radio and display receiver assembly (EMVN ECU) continuously for 3 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the combination meter assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0182 Lost Communication with Lighting Control Module Front Communication stop occurs between the combination meter assembly and No. 1 headlight ECU sub-assembly LH continuously for 10 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the combination meter assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - - DTC is stored until it is cleared using the GTS.
U023A Lost Communication with Front Camera Module Communication stop occurs between the combination meter assembly and forward recognition camera continuously for 10 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the combination meter assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - - DTC is stored until it is cleared using the GTS.


e.

Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM Communication stop occurs between the air conditioning amplifier assembly and ECM continuously for 5 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 15 seconds. - - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Main Body ECU Communication stop occurs between the air conditioning amplifier assembly and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 15 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Combination Meter Communication stop occurs between the air conditioning amplifier assembly and combination meter assembly continuously for 5 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 15 seconds. - - DTC is stored until it is cleared using the GTS.
U0163 Lost Communication with Navigation Control Module Communication stop occurs between the air conditioning amplifier assembly and the radio and display receiver assembly (EMVN ECU) continuously for 5 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 15 seconds. - - DTC is stored until it is cleared using the GTS.


f.

No. 1 Headlight ECU Sub-assembly LH / GTS Display "AFS" (for LED Headlight)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to the Lighting System

Click here(Click here)

U0073 Control Module Communication Bus Off The No. 1 headlight ECU sub-assembly LH is unable to send or receive data 10 times consecutively. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The No. 1 headlight ECU sub-assembly LH power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the No. 1 headlight ECU sub-assembly LH and ECM continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The No. 1 headlight ECU sub-assembly LH power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0101 Lost Communication with TCM Communication stop occurs between the No. 1 headlight ECU sub-assembly LH and ECM continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The No. 1 headlight ECU sub-assembly LH power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the No. 1 headlight ECU sub-assembly LH and steering sensor continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The No. 1 headlight ECU sub-assembly LH power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Either of the following conditions is met:
·

Communication stop occurs between the No. 1 headlight ECU sub-assembly LH and skid control ECU continuously for 5 seconds or more.

·

Communication stop occurs between the No. 1 headlight ECU sub-assembly LH and skid control ECU continuously for 10 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The No. 1 headlight ECU sub-assembly LH power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0132 Lost Communication with Ride Level Control Module Communication stop occurs between the No. 1 headlight ECU sub-assembly LH and suspension control ECU continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The No. 1 headlight ECU sub-assembly LH power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the No. 1 headlight ECU sub-assembly LH and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The No. 1 headlight ECU sub-assembly LH power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the No. 1 headlight ECU sub-assembly LH and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The No. 1 headlight ECU sub-assembly LH power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U023A Lost Communication With Image Processing Module "A" Communication stop occurs between the No. 1 headlight ECU sub-assembly LH and forward recognition camera continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The No. 1 headlight ECU sub-assembly LH power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U1000* CAN Communication Failure(Message Registry) CAN communication malfunction (message register) All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The No. 1 headlight ECU sub-assembly LH power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.


g.

Power Steering ECU Assembly / GTS Display "PPS"

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM / PCM "A" Communication stop occurs between the power steering ECU assembly and ECM continuously for approximately 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the power steering ECU assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 2 seconds. PPS warning light illuminates. - DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the power steering ECU assembly and steering sensor continuously for approximately 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the power steering ECU assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 2 seconds. PPS warning light illuminates. - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the power steering ECU assembly and skid control ECU continuously for approximately 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the power steering ECU assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 2 seconds. PPS warning light illuminates. - DTC is stored until it is cleared using the GTS.


h.

Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the main body ECU (multiplex network body ECU) and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0101 Lost Communication with TCM Communication stop occurs between the main body ECU (multiplex network body ECU) and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0120 Lost Communication with Starter / Generator Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and certification ECU (smart key ECU assembly) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and skid control ECU assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and airbag sensor assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. TPMS indicator light blinks, and then illuminates. - DTC is stored until it is cleared using the GTS.
U0164 Lost Communication with HVAC Control Module Communication stop occurs between main body ECU (multiplex network body ECU) and air conditioning amplifier assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0182 Lost Communication with AFS Communication stop occurs between the main body ECU (multiplex network body ECU) and No. 1 headlight ECU sub-assembly LH continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. AHB indicator light illuminates. - DTC is stored until it is cleared using the GTS.
U0199 Lost Communication with ''Door Control Module A'' Communication stop occurs between the main body ECU (multiplex network body ECU) and outer mirror control ECU assembly RH continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0200 Lost Communication with ''Door Control Module B'' Communication stop occurs between the main body ECU (multiplex network body ECU) and outer mirror control ECU assembly LH continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0208 Lost Communication with ''Seat Control Module A'' Communication stop occurs between the main body ECU (multiplex network body ECU) and front power seat switch (power seat control ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U023A Lost Communication With Image Processing Module "A" Communication stop occurs between the main body ECU (multiplex network body ECU) and forward recognition camera continuously for 5 seconds or more. All conditions are met:
·

5 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. AHB indicator light blinks. - DTC is stored until it is cleared using the GTS.
U0327 Software Incompatibility with Vehicle Security Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and certification ECU (smart key ECU assembly) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1002 Lost Communication with Gateway Module The main body ECU (multiplex network body ECU) detects a problem when communicating with the outer mirror control ECU assembly LH, outer mirror control ECU assembly RH, front power seat switch (power seat control ECU) and the multiplex tilt and telescopic ECU. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1115 Lost Communication with Tilt & Telescopic Module Communication stop occurs between the main body ECU (multiplex network body ECU) and the multiplex tilt and telescopic ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


i.

Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System)

i.

GTS Display "Power Source Control"

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 ECM/EV Communication Communication stop occurs between the certification ECU (smart key ECU assembly) and ECM continuously for approximately 4 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. - - DTC is stored until it is cleared using the GTS.
U0129 Vehicle Speed Signal Communication The certification ECU (smart key ECU assembly) is unable to receive certain data from the skid control ECU for approximately 4 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. - - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) continuously for 3 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and combination meter assembly continuously for approximately 4 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. - - DTC is stored until it is cleared using the GTS.
U1103 Lost Communication with Stop and Start Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and the stop and start ECU continuously for 5 seconds or more. All conditions are met:
·

Ignition switch ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - - DTC is stored until it is cleared using the GTS.


ii.

GTS Display "Entry&Start"

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM/PCM/EV "A" Communication stop occurs between the certification ECU (smart key ECU assembly) and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON or ACC, and then wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B Communication stop occurs between the certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON or ACC, and then wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON or ACC, and then wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1103 Lost Communication with Stop and Start Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and the stop and start ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON or ACC, and then wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


iii.

GTS Display "Starting Control"

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the certification ECU (smart key ECU assembly) and ECM continuously for 2 seconds or more. Ignition switch ON. Turn the ignition switch to ON and wait at least 2 second. - - DTC remains stored only while malfunction is occurring.



j.

Radio and Display Receiver Assembly (EMVN ECU) / GTS Display "Navigation System" (w/ Audio and Visual System (for Radio and Display Type), Navigation System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Navigation System or Audio and Visual System (for Radio and Display Type)

w/ Navigation System: Click here(Click here)

w/ Audio and Visual System (for Radio and Display Type): Click here(Click here)

U0073 Sending Malfunction (Navigation to APGS) Either of the following conditions is met:
·

Bus off condition is detected.

·

CAN bus is not connected.


All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0100 Engine /EV ECU Communication Communication stop occurs between the radio and display receiver assembly (EMVN ECU) and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
Communication stop occurs between the radio and display receiver assembly (EMVN ECU) and ECM continuously for 11 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 21 seconds. - - DTC is stored until it is cleared using the GTS.
Communication stop occurs between the radio and display receiver assembly (EMVN ECU) and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.

·

The vehicle speed is 20 km/h (12 mph) or more.


Drive the vehicle for 10 seconds or more at a speed of 20 km/h (12 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Either of the following conditions is met:
·

Communication stop occurs between the radio and display receiver assembly (EMVN ECU) and skid control ECU continuously for 10 seconds or more.

·

Data from the skid control ECU cannot be a received by the radio and display receiver assembly (EMVN ECU) at vehicle speed of 20 km/h (12 mph) or more continuously for 10 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Drive the vehicle for 13 seconds or more at a speed of 20 km/h (12 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0132 Air Suspension ECU Communication Data from the suspension control ECU cannot be a received by the radio and display receiver assembly (EMVN ECU) at vehicle speed of 20 km/h (12 mph) or more continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Drive the vehicle for 10 seconds or more at a speed of 20 km/h (12 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module Communication stop occurs between the radio and display receiver assembly (EMVN ECU) and main body ECU (multiplex network body ECU) continuously for 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Meter ECU Communication Communication stop occurs between the radio and display receiver assembly (EMVN ECU) and combination meter assembly continuously for 30 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 33 seconds. - - DTC is stored until it is cleared using the GTS.
U0164 Air Conditioner ECU Communication Communication stop occurs between the radio and display receiver assembly (EMVN ECU) and air conditioning amplifier assembly continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC is stored until it is cleared using the GTS.
U023B Lost Communication with Image Processing Module "B" Communication stop occurs between the radio and display receiver assembly (EMVN ECU) and parking assist ECU continuously for approximately 12 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 15 seconds. - - DTC is stored until it is cleared using the GTS.
U0265* Lost Communication with Image Processing Sensor "A" Communication stop occurs between the radio and display receiver assembly (EMVN ECU) and rear television camera continuously for approximately 12 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 15 seconds. - - DTC is stored until it is cleared using the GTS.
U1110 Clearance Sonar ECU Communication Communication stop occurs between the radio and display receiver assembly (EMVN ECU) and clearance warning ECU assembly continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly (EMVN ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC is stored until it is cleared using the GTS.


k.

Telephone Transceiver Assembly / GTS Display "Telematics" (w/ Telematics System)

HINT:

DTC communication uses the CAN communication system.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the telephone transceiver assembly and main body ECU (multiplex network body ECU) continuously for approximately 10 seconds or more.
All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the telephone transceiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 20 seconds. - - DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the telephone transceiver assembly and combination meter assembly continuously for approximately 10 seconds or more.
All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the telephone transceiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 20 seconds. - - DTC is stored until it is cleared using the GTS.


l.

Suspension Control ECU / GTS Display "Air suspension" (w/ Air Suspension System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the suspension control ECU and ECM continuously for 3 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The vehicle speed is 30 km/h (19 mph) or more.

·

The power source voltage of the suspension control ECU is 10 V or higher.


Drive the vehicle for 4 seconds or more at a speed of 30 km/h (19 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0114 Lost Communication with Four-Wheel Drive Clutch Control Module Communication stop occurs between the suspension control ECU and 4 wheel drive control ECU (4WD control ECU) continuously for 3 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the suspension control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. - - DTC is stored until it is cleared using the GTS.
U0122 Lost Communication with Vehicle Dynamics Control Module Communication stop occurs between the suspension control ECU and skid control ECU continuously for 3 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the suspension control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0124 Lost Communication with Lateral Acceleration Sensor Module Communication stop occurs between the suspension control ECU and airbag sensor assembly continuously for 3 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the suspension control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. - - DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the suspension control ECU and steering sensor continuously for 3 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the suspension control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module Communication stop occurs between the suspension control ECU and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the suspension control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 11 seconds. - - DTC is stored until it is cleared using the GTS.
U1103 Lost Communication with Stop and Start Control Module Communication stop occurs between the suspension control ECU and the stop and start ECU continuously for 3 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The vehicle speed is 30 km/h (19 mph) or more.


Drive the vehicle for 4 seconds or more at a speed of 30 km/h (19 mph) or higher. - - DTC is stored until it is cleared using the GTS.


m.

4 Wheel Drive Control ECU (4WD Control ECU) / GTS Display "Four Wheel Drive"

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Transfer System

Click here(Click here)

U0100 Lost Communication with ECM / PCM "A" Either of the following conditions is met:
·

Communication stop occurs between the 4 wheel drive control ECU (4WD control ECU) and ECM continuously for approximately 2 seconds or more.

·

Communication stop occurs between the 4 wheel drive control ECU (4WD control ECU) and ECM continuously for approximately 6 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the 4 wheel drive control ECU (4WD control ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 9 seconds. 4LO indicator light blinks. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0122 Lost Communication with Vehicle Dynamics Control Module Communication stop occurs between the 4 wheel drive control ECU (4WD control ECU) and skid control ECU continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the 4 wheel drive control ECU (4WD control ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds.
·

4LO indicator light blinks.

·

Center differential lock indicator light blinks.

·

Rear differential lock indicator light blinks.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0416* Invalid Data Received from Vehicle Dynamics Control Module Wheel speed sensor malfunction signals from skid control ECU are received for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the 4 wheel drive control ECU (4WD control ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. 4LO indicator light blinks. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


n.

Clearance warning ECU assembly / GTS Display "Clearance Sonar" (w/ TOYOTA Parking Assist-sensor System [w/ Multi-display])

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the clearance warning ECU assembly and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0101 Lost Communication with TCM Communication stop occurs between the clearance warning ECU assembly and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the clearance warning ECU assembly and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication With Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the clearance warning ECU assembly and combination meter assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.


o.

Tire Pressure Warning ECU and Receiver / GTS Display "Tire Pressure Monitor" (w/ Tire Pressure Warning System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the tire pressure warning ECU and receiver and the skid control ECU continuously for 60 seconds or more. Approximately 1 second or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 61 seconds. - - DTC remains stored only while malfunction is occurring.


p.

Multiplex Tilt and Telescopic ECU / GTS Display "Tilt & Telescopic" (for Power Tilt and Power Telescopic Steering Column)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0142 Lost Communication with Body ECU Either of the following conditions is met:
·

Communication stop occurs between the multiplex tilt and telescopic ECU and main body ECU (multiplex network body ECU) continuously for approximately 4 seconds or more.

·

Communication stop occurs between the multiplex tilt and telescopic ECU and main body ECU (multiplex network body ECU) continuously for 10 seconds or more.


All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the multiplex tilt and telescopic ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0208 Lost Communication with D-Seat ECU Communication stop occurs between the multiplex tilt and telescopic ECU and front power seat switch (power seat control ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the multiplex tilt and telescopic ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1112 Lost Communication with Combination Switch ECU Communication stop occurs between the multiplex tilt and telescopic ECU and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the multiplex tilt and telescopic ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


q.

Stabilizer Control ECU / GTS Display "KDSS" (w/ Kinetic Dynamic Suspension System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the stabilizer control ECU and ECM continuously for 3 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The vehicle speed is 30 km/h (19 mph) or more.

·

The power source voltage of the stabilizer control ECU is 10 V or higher.


Drive the vehicle for 4 seconds or more at a speed of 30 km/h (19 mph) or higher. - - DTC is stored until it is cleared using the GTS.
U0122 Lost Communication with Vehicle Dynamics Control Module Communication stop occurs between the stabilizer control ECU and skid control ECU continuously for 3 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the stabilizer control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. KDSS indicator light illuminates. - DTC is stored until it is cleared using the GTS.
U0124 Lost Communication with Lateral Acceleration Sensor Module Communication stop occurs between the stabilizer control ECU and airbag sensor assembly continuously for 3 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the stabilizer control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. KDSS indicator light illuminates. - DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the stabilizer control ECU and steering sensor continuously for 3 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is ON.

·

The power source voltage of the stabilizer control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. KDSS indicator light illuminates. - DTC is stored until it is cleared using the GTS.


r.

Blind Spot Monitor Sensor LH / GTS Display "Blind Spot Monitor Master" (w/ Blind Spot Monitor System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM / PCM "A" Communication stop occurs between the blind spot monitor sensor LH and ECM continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The vehicle speed is 5 km/h (3 mph) or more.

·

The power source voltage of the blind spot monitor sensor LH is 10 V or higher.

·

The blind spot monitor main switch is ON.


Drive the vehicle for approximately 14 seconds or more at a speed of 5 km/h (3 mph) or higher with the blind spot monitor main switch ON. BSM indicator illuminates (umber). Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Either of the following conditions is met:
·

Communication stop occurs between the blind spot monitor sensor LH and steering sensor continuously for approximately 4 seconds or more.

·

Communication stop occurs between the blind spot monitor sensor LH and steering sensor continuously for approximately 11 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the blind spot monitor sensor LH is 10 V or higher.

·

The blind spot monitor main switch is ON.


Turn the ignition switch to ON and wait at least approximately 14 seconds with the blind spot monitor main switch ON. BSM indicator illuminates (umber). Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the blind spot monitor sensor LH and skid control ECU continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the blind spot monitor sensor LH is 10 V or higher.

·

The blind spot monitor main switch is ON.


Turn the ignition switch to ON and wait at least approximately 7 seconds with the blind spot monitor main switch ON. BSM indicator illuminates (umber). Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the blind spot monitor sensor LH and main body ECU (multiplex network body ECU) continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the blind spot monitor sensor LH is 10 V or higher.

·

The blind spot monitor main switch is ON.


Turn the ignition switch to ON and wait at least approximately 14 seconds with the blind spot monitor main switch ON. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


s.

Outer Mirror Control ECU Assembly LH / GTS Display "Mirror L" (w/ Reverse Shift-linked Mirror)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0142 Lost Communication With Body Control Module "B" Communication stop occurs between the outer mirror control ECU assembly LH and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

1 second or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the outer mirror control ECU assembly LH is 10 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - - DTC is stored until it is cleared using the GTS.


t.

Outer Mirror Control ECU Assembly RH / GTS Display "Mirror R" (w/ Reverse Shift-linked Mirror)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0142 Lost Communication With Body Control Module "B" Communication stop occurs between the outer mirror control ECU assembly RH and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

1 second or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the outer mirror control ECU assembly RH is 10 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - - DTC is stored until it is cleared using the GTS.


u.

Engine Stop and Start ECU / GTS Display "Stop and Start" (w/ Stop and Start System)

HINT:

DTC communication uses the CAN communication system.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the engine stop and start ECU and ECM continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U010187 Lost Communication with TCM Missing Message Communication stop occurs between the engine stop and start ECU and transmission control ECU continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 14 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the engine stop and start ECU and steering sensor continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the engine stop and start ECU and brake actuator assembly (skid control ECU) continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U013187 Lost Communication with Power Steering Control Module Missing Message Communication stop occurs between the engine stop and start ECU and the rack and pinion power steering gear assembly continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the engine stop and start ECU and main body ECU (multiplex network body ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U015187 Lost Communication with Restraints Control Module Missing Message Communication stop occurs between the engine stop and start ECU and airbag sensor assembly continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 14 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U016487 Lost Communication with HVAC Control Module Missing Message Communication stop occurs between the engine stop and start ECU and air conditioning amplifier assembly continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 14 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U023A87 Lost Communication with Image Processing Module "A" Missing Message Communication stop occurs between the engine stop and start ECU and forward recognition camera continuously for 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U111087 Lost Communication with Clearance Sonar Module Missing Message Communication stop occurs between the engine stop and start ECU and clearance warning ECU assembly continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.


v.

Forward Recognition Camera (w/ Pre-collision System)

i.

GTS Display "Radar Cruise2"

HINT:

DTC communication uses the CAN communication system.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Dynamic Radar Cruise Control System

Click here(Click here)

U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 25 km/h (16 mph) or more.


Drive the vehicle for approximately 4 seconds or more at a speed of 25 km/h (16 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 25 km/h (16 mph) or more.


Drive the vehicle for approximately 4 seconds or more at a speed of 25 km/h (16 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 25 km/h (16 mph) or more.


Drive the vehicle for approximately 4 seconds or more at a speed of 25 km/h (16 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 25 km/h (16 mph) or more.


Drive the vehicle for approximately 5 seconds or more at a speed of 25 km/h (16 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the forward recognition camera and combination meter assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 25 km/h (16 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 25 km/h (16 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587* Lost Communication with Control Front Distance Range Sensor Missing Message The forward recognition camera does not receive data from the millimeter wave radar sensor assembly for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 5 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030051* Internal Control Module Software Incompatibility Not Programmed The control system information sent from the ECM remains undefined by the forward recognition camera for 3 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 6 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030057* Internal Control Module Software Incompatibility Invalid / Incompatible Software Component The vehicle information sent from the ECM does not match that stored in the forward recognition camera for 1 second or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 4 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U031851* Software Incompatibility with Brake System Control Module Not Programmed The vehicle information sent from brake actuator assembly (skid control ECU) remains undefined by the forward recognition camera for 3 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 6 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U031857* Software Incompatibility with Brake System Control Module Invalid / Incompatible Software Component The vehicle information sent from the brake actuator assembly (skid control ECU) does not match that stored in the forward recognition camera for 2 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 5 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U032251* Software Incompatibility with Body Control Module Not Programmed The vehicle information sent from main body ECU (multiplex network body ECU) remains undefined by the forward recognition camera for 6 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 9 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U032257* Software Incompatibility with Body Control Module Invalid / Incompatible Software Component The vehicle information sent from the main body ECU (multiplex network body ECU) does not match that stored in the forward recognition camera for 4 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 7 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U040181* The information sent from the ECM does not match that stored in the forward recognition camera. The information sent from the ECM does not match that stored in the forward recognition camera. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 3 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U110687 Lost Communication with Electric Parking Brake Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 25 km/h (16 mph) or more.


Drive the vehicle for approximately 5 seconds or more at a speed of 25 km/h (16 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


ii.

GTS Display "Pre-Collision System"

HINT:

DTC communication uses the CAN communication system.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Pre-collision System

Click here(Click here)

U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.


Drive the vehicle speed of 5 km/h (3 mph) or more. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.


Drive the vehicle speed of 5 km/h (3 mph) or more. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU). All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587* Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message Communication stop occurs between the forward recognition camera and millimeter wave radar sensor assembly. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U110487 Lost Communication with Driving Support ECU Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


iii.

GTS Display "Lane Control"

HINT:

DTC communication uses the CAN communication system.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Lane Departure Alert System

Click here(Click here)

U010087 Lost Communication with ECM/PCM "A" Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The LDA main switch is on.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U010187 Lost Communication with TCM Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The LDA main switch is on.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The LDA main switch is on.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The LDA main switch is on.


Turn the ignition switch to ON and wait at least 8 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The LDA main switch is on.


Turn the ignition switch to ON and wait at least 8 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U013187 Lost Communication with Power Steering Control Module Missing Message Communication stop occurs between the forward recognition camera and the rack and pinion power steering gear assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The LDA main switch is on.


Turn the ignition switch to ON and wait at least 8 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the forward recognition camera and combination meter assembly continuously for 50 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The LDA main switch is on.


Turn the ignition switch to ON and wait at least 53 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message Communication stop occurs between the forward recognition camera and millimeter wave radar sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The LDA main switch is on.


Turn the ignition switch to ON and wait at least 8 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030051* Internal Control Module Software Incompatibility Not Programmed The vehicle information sent from the ECM remains undefined by the forward recognition camera. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The LDA main switch is on.

·

The power source voltage of the forward recognition camera is 7 V or more.


Turn the LDA main switch on and wait for at least approximately 3 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030057* Internal Control Module Software Incompatibility Invalid/Incompatible Software Component The vehicle information sent from the ECM does not match that stored in the forward recognition camera for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The LTA main switch is on.

·

The power source voltage of the forward recognition camera is 7 V or more.


Turn the LTA main switch on and wait for at least approximately 8 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


iv.

GTS Display "Road Sign Assist" (w/ Road Sign Assist System)

HINT:

DTC communication uses the CAN communication system.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the forward recognition camera and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the forward recognition camera and combination meter assembly continuously for 50 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 53 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


v.

GTS Display "Front Recognition Camera (Front Lighting Control)"

HINT:

DTC communication uses the CAN communication system.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Lighting System

for Halogen Headlight: Click here(Click here)

for LED Headlight: Click here(Click here)

U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 7 seconds or more at a speed of 1 km/h (1 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 7 seconds or more at a speed of 1 km/h (1 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the forward recognition camera and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587* Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message Communication stop occurs between the forward recognition camera and millimeter wave radar sensor assembly continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


vi.

GTS Display "Front Recognition Camera"

HINT:

DTC communication uses the CAN communication system.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - - DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - - DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the forward recognition camera and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.



w.

Millimeter Wave Radar Sensor Assembly / GTS Display "Front Radar Sensor" (w/ Pre-collision System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Front Radar Sensor System

Click here(Click here)

U010487* Lost Communication with Driving Support ECU Missing Message The millimeter wave radar sensor assembly does not receive data from the forward recognition camera for approximately 1 second or more. All conditions are met:
·

The ignition switch is ON for approximately 1 second or more.

·

The power source voltage of the millimeter wave radar sensor assembly is 8 V or higher.


Turn the ignition switch to ON and wait for at least approximately 2 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030557* Software Incompatibility with Cruise Control Module Invalid / Incompatible Software Component The control system information sent from the forward recognition camera does not match that stored in the millimeter wave radar sensor assembly for 7 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 1 second or more.

·

The power source voltage of the millimeter wave radar sensor assembly is 8 V or higher.


Turn the ignition switch to ON and wait for at least approximately 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


x.

Parking Assist ECU / GTS Display "Intelligent Parking Assist System / Back Guide Monitor " (w/ Multi-terrain Monitor System)

HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Multi-terrain Monitor System

Click here(Click here)

U0073 Control Module Communication Bus "A" Off One of the following conditions is met:
·

The parking assist ECU is unable to send or receive data for approximately 1 second or more.

·

The parking assist ECU cannot send or receive data (the bus is off) 10 times consecutively.


All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0100 Lost Communication with ECM/PCM "A" One of the following conditions is met:
·

The ignition switch is ON for approximately 4 seconds or more

·

The parking assist ECU is unable to receive certain data from the ECM for 10 seconds or more.


All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0114 Lost Communication with 4WD Control ECU The parking assist ECU is unable to receive certain data from the 4WD control ECU for approximately 2 seconds or more. All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0124 Lost Communication with Lateral Acceleration Sensor Module The parking assist ECU is unable to receive certain data from the airbag sensor assembly for approximately 2 seconds or more. All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module One of the following conditions is met:
·

The parking assist ECU is unable to receive certain data from the steering sensor for approximately 2 seconds or more.

·

The parking assist ECU is unable to receive certain data from the steering sensor for 10 seconds or more.


All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module One of the following conditions is met:
·

The parking assist ECU is unable to receive certain data from the master cylinder solenoid (skid control ECU) for approximately 2 seconds or more.

·

The parking assist ECU is unable to receive certain data from the master cylinder solenoid (skid control ECU) for approximately 4 seconds or more.

·

The parking assist ECU is unable to receive certain data from the master cylinder solenoid (skid control ECU) for 10 seconds or more.


All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module One of the following conditions is met:
·

The parking assist ECU is unable to receive certain data from the main body ECU (multiplex network body ECU) for 4 seconds or more.

·

The parking assist ECU is unable to receive certain data from the main body ECU (multiplex network body ECU) for 6 seconds or more.

·

The parking assist ECU is unable to receive certain data from the main body ECU (multiplex network body ECU) for 10 seconds or more.


All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0140 Lost Communication with HVAC Control Module The parking assist ECU is unable to receive certain data from the radio and display receiver assembly (EMVN ECU) for 10 seconds or more. All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U0233 Lost Communication with Blind Spot Monitor Master Module The parking assist ECU is unable to receive certain data from the blind spot monitor sensor LH for 10 seconds or more. All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.
U1000* CAN Communication Failure(Message Registry) CAN transmission malfunction (message register) All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - The DTC remains stored until it is cleared using the GTS.
U1110 Lost Communication with Clearance Sonar Module The parking assist ECU is unable to receive certain data from the clearance warning ECU assembly for 10 seconds or more. All conditions are met:
·

The ignition switch is ON for 3 seconds or more.

·

The parking assist ECU power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - The DTC remains stored until it is cleared using the GTS.


y.

Central Gateway ECU (Network Gateway ECU) / GTS Display "Central Gateway"

HINT:

The central gateway ECU (network gateway ECU) is connected to the CAN communication system but CAN communication DTCs are not stored.



z.

Front Power Seat Switch (Power Seat Control ECU) / GTS Display "Driver Seat" (w/ Seat Memory)

HINT:

The front power seat switch (power seat control ECU) is connected to the CAN communication system but CAN communication DTCs are not stored.



aa.

Steering Sensor / GTS Display "-"

HINT:

The steering sensor is connected to the CAN communication system but CAN communication DTCs are not stored.



ab.

Airbag Sensor Assembly / GTS Display "SRS Airbag"

HINT:

The airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.




CAN BUS WAVEFORMS


C353604E02
1.521,0.677 1.854,0.281 1.854,0.281 1.99,0.281 false 4.427,1 4.427,0.271 4.427,0.271 4.563,0.271 true 4.438,3.948 4.438,2.521 4.438,2.521 5.219,2.521 true 6.354,3.948 6.354,2.521 6.354,2.521 5.646,2.521 true 5.375,3.688 5.375,4.781 5.375,4.781 5.51,4.781 false 2.063,0.208 3.208,0.448 1.146,0.24 10 false CAN Main Bus 4.656,0.198 7.052,0.479 2.396,0.281 10 false Open in CAN Main Bus Line (CANH) 5.313,3.167 6.385,3.365 1.073,0.198 10 false ECU 3.417,3.167 4.49,3.365 1.073,0.198 10 false ECU 1.594,3.167 2.667,3.365 1.073,0.198 10 false ECU 3.885,4.01 5.208,4.531 1.323,0.521 10 false Open in CAN Branch Line (CANL) 5.76,4 7.073,4.49 1.313,0.49 10 false Open in CAN Branch Line (CANH) 5.604,4.708 6.708,5.177 1.104,0.469 10 false CAN Branch 1.469,4.781 3.802,5.031 2.333,0.25 10 false : CAN Main Bus Line (CANH) 1.479,5.219 3.677,5.521 2.198,0.302 10 false : CAN Main Bus Line (CANL) 1.479,5.813 3.51,6.094 2.031,0.281 10 false : CAN Branch Line (CANH) 1.469,6.25 3.625,6.521 2.156,0.271 10 false : CAN Branch Line (CANL)

HINT:
·

The following waveforms are measured between terminals CANH and GND, and terminals CANL and GND of the central gateway ECU (network gateway ECU). (Use this as a reference for diagnosis of CAN communication lines.)

·

When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).

·

Wiggle the connector and wire harness to check if the waveform changes.



a.

CAN bus waveforms (Group 1)

i.
C265973N07
0.49,0.438 0.573,0.438 0.573,0.438 0.906,0.781 true 0.458,1.594 0.552,1.594 0.552,1.594 0.917,1.156 true 0.052,0.333 0.667,0.531 0.615,0.198 10 false CANH 0.031,1.5 0.646,1.698 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.708,0.229 3.427,0.427 0.719,0.198 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Normal waveform


ii.
C265974N05
1.469,1.479 1.552,1.479 1.552,1.479 1.969,1.104 true 1.521,0.49 1.604,0.49 1.604,0.49 1.969,0.792 true 1.094,0.385 1.708,0.583 0.615,0.198 10 false CANH 1.063,1.385 1.677,1.583 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND 2.688,0.229 3.375,0.406 0.688,0.177 10 false 1 V/DIV.

Open in both of the lines (CANH and CANL) of a CAN branch

HINT:
·

Waveforms (waveforms shown using dotted lines) are not output from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)

·

Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.




iii.
C265975N05
1.292,0.917 0.573,0.458 0.573,0.458 0.51,0.458 true 0.469,1.417 0.552,1.417 0.552,1.417 1.063,0.958 true 0.073,0.354 0.688,0.552 0.615,0.198 10 false CANH 0.063,1.323 0.677,1.521 0.615,0.198 10 false CANL 1.344,1.917 2.875,2.115 1.531,0.198 10 false 50 μs/DIV. 2.719,0.229 3.344,0.438 0.625,0.208 10 false 1 V/DIV. 2.958,1.354 3.417,1.552 0.458,0.198 10 false GND

Short between the CAN bus lines (CANH and CANL)

HINT:
·

Waveforms disappear.

·

If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.





b.

CAN bus waveforms (reference) (Group 2)

NOTICE:

The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.


i.
C265976N05
0.938,0.76 0.583,0.458 0.583,0.458 0.49,0.458 true 0.458,1.552 0.552,1.552 0.552,1.552 0.854,1.146 true 0.063,0.354 0.677,0.552 0.615,0.198 10 false CANH 0.063,1.458 0.677,1.656 0.615,0.198 10 false CANL 1.313,1.927 2.844,2.125 1.531,0.198 10 false 50 μs/DIV. 2.708,0.229 3.344,0.448 0.635,0.219 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN branch line (CANH)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




ii.
C265977N05
0.479,1.406 0.573,1.406 0.573,1.406 0.885,1.125 true 0.5,0.438 0.573,0.438 0.573,0.438 0.833,0.74 true 0.063,0.333 0.677,0.531 0.615,0.198 10 false CANH 0.052,1.302 0.667,1.5 0.615,0.198 10 false CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.417,0.458 0.719,0.229 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN branch line (CANL)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




iii.
C265978N05
0.49,0.406 0.573,0.406 0.573,0.406 0.938,0.708 true 0.469,1.458 0.552,1.458 0.552,1.458 0.938,1.156 true 0.063,0.302 0.677,0.5 0.615,0.198 10 false CANH 0.063,1.365 0.677,1.563 0.615,0.198 10 false CANL 1.323,1.927 2.854,2.125 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.281,0.469 0.583,0.24 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN main bus line (CANH)

HINT:
·

Waveforms of ECUs or sensors that are closer to the central gateway ECU (network gateway ECU) than the open part are almost normal.

·

Waveforms of ECUs or sensors that are on the opposite side of the central gateway ECU (network gateway ECU) from the open part are abnormal.

·

An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.




iv.
C265979N05
0.458,1.813 0.563,1.813 0.563,1.813 1.083,1.531 true 1.063,1.333 0.573,0.906 0.573,0.906 0.49,0.906 true 0.052,0.802 0.667,1 0.615,0.198 10 false CANH 0.042,1.708 0.656,1.906 0.615,0.198 10 false CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 false 50 μs/DIV. 2.719,0.229 3.375,0.479 0.656,0.25 10 false 1 V/DIV. 2.99,1.354 3.385,1.563 0.396,0.208 10 false GND

Short between a CAN bus line (CANH) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.

·

A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.




v.
C265980N05
0.458,1.76 0.563,1.76 0.563,1.76 0.948,1.385 true 0.458,0.5 0.552,0.5 0.552,0.5 1.021,0.708 true 0.031,0.406 0.646,0.604 0.615,0.198 10 false CANH 0.052,1.667 0.667,1.865 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.292,0.49 0.594,0.26 10 false 1 V/DIV. 2.969,1.354 3.354,1.604 0.385,0.25 10 false GND

Short between a CAN bus line (CANL) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.

·

A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.






DATA SENDING/RECEIVING TABLE


a.

Data sending/receiving table

HINT:

If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.


Data Content Data Detected and Sent by Relevant Data List Item Relevant Data List Item
Can be Checked in Data List Cannot be Checked in Data List Selected System*3 Data List Item
Engine speed signal ECM
·

Brake actuator assembly (skid control ECU)

·

Master cylinder solenoid (skid control ECU)

·

Certification ECU (smart key ECU assembly)

·

Combination meter assembly

·

Suspension control ECU

·

Power steering ECU assembly

·

Engine stop and start ECU


·

Radio and display receiver assembly (EMVN ECU)

·

Airbag sensor assembly

·

Air conditioning amplifier assembly

·

Main body ECU (multiplex network body ECU)

·

4 wheel drive control ECU (4WD control ECU)

·

Telephone transceiver assembly


Engine Engine Speed
ABS/VSC/TRC Engine Revolutions
Starting Control Engine Speed
Combination Meter Engine Rpm
Air Suspension Engine Speed
Stop and Start Engine Speed (ECM)
PPS Engine Revolution
Engine coolant temperature signal ECM
·

Air conditioning amplifier assembly

·

Combination meter assembly

·

Engine stop and start ECU


Radio and display receiver assembly (EMVN ECU) Engine Coolant Temp
Engine Coolant Temperature
Air Conditioner Engine Coolant Temp
Combination Meter Coolant Temperature
Stop and Start Coolant Temperature
Shift position signal ECM
·

Certification ECU (smart key ECU assembly) (Start control/P only)

·

4 wheel drive control ECU (4WD control ECU)(P or N only)

·

Clearance warning ECU assembly

·

Radio and display receiver assembly (EMVN ECU)

·

Blind spot monitor sensor LH (R only)

·

Combination meter assembly*1

·

Power seat switch assembly (P only)

·

Engine stop and start ECU


·

Airbag sensor assembly

·

No. 1 headlight ECU sub-assembly LH

·

Main body ECU (multiplex network body ECU)

·

Forward recognition camera (R only)

·

Parking assist ECU

·

Telephone transceiver assembly


Engine N Range Status
Power Source Control Shift P Signal
Navigation System Reverse Signal
Four Wheel Drive Shift SW Status (P Range)
Clearance Sonar
·

Parking Signal

·

Reverse Signal


Combination Meter Reverse Range Switch (6MT)*4
Driver Seat P Switch
Blind Spot Monitor Master Reverse
Stop and Start Shift Position
Stop light switch signal
·

Brake actuator assembly (skid control ECU)

·

Master cylinder solenoid (skid control ECU)


·

Engine stop and start ECU

·

4 wheel drive control ECU (4WD control ECU)


·

Airbag sensor assembly

·

Stabilizer control ECU

·

Suspension control ECU

·

Telephone transceiver assembly


ABS/VSC/TRC Stop Light SW
Four Wheel Drive Stop Light SW
Stop and Start Stop Light SW (ABS/VSC)
Wheel speed signal
·

Brake actuator assembly (skid control ECU)

·

Master cylinder solenoid (skid control ECU)


·

Suspension control ECU

·

4 wheel drive control ECU (4WD control ECU)

·

No. 1 headlight ECU sub-assembly LH

·

Stabilizer control ECU


·

Airbag sensor assembly

·

ECM

·

Blind spot monitor sensor LH

·

Parking assist ECU

·

Telephone transceiver assembly


ABS/VSC/TRC
·

FR Wheel Speed

·

FL Wheel Speed

·

RR Wheel Speed

·

RL Wheel Speed


Air Suspension
·

FR Wheel Speed

·

FL Wheel Speed

·

RR Wheel Speed

·

RL Wheel Speed


Four Wheel Drive
·

FR Wheel Speed

·

FL Wheel Speed

·

RR Wheel Speed

·

RL Wheel Speed


KDSS
·

FR Wheel Speed

·

FL Wheel Speed

·

RR Wheel Speed

·

RL Wheel Speed


AFS
·

FR Wheel Speed

·

FL Wheel Speed


Vehicle speed signal
·

Brake actuator assembly (skid control ECU)

·

Master cylinder solenoid (skid control ECU)


·

Engine stop and start ECU

·

Radio and display receiver assembly (EMVN ECU)

·

ECM

·

4 wheel drive control ECU (4WD control ECU)

·

Combination meter assembly*2

·

Blind spot monitor sensor LH

·

Forward recognition camera


·

Airbag sensor assembly

·

Parking assist ECU

·

Telephone transceiver assembly

·

Main body ECU (multiplex network body ECU)

·

Power steering ECU assembly

·

Telephone transceiver assembly


ABS/VSC/TRC Vehicle Speed
Engine Vehicle Speed
Navigation System Vehicle Speed
Four Wheel Drive Vehicle Speed
Blind Spot Monitor Master Vehicle Speed
Stop and Start Vehicle Speed
Combination Meter Vehicle Speed Meter
Radar Cruise 2 Vehicle Speed
Combination meter assembly*2
·

Multiplex tilt and telescopic ECU

·

Power seat switch assembly


·

Clearance warning ECU assembly

·

Airbag sensor assembly

·

Air conditioning amplifier assembly

·

Main body ECU (multiplex network body ECU)

·

Certification ECU (smart key ECU assembly)

·

Tire pressure warning ECU and receiver

·

Telephone transceiver assembly


Combination Meter Vehicle Speed Meter
Tilt&Telescopic Freeze Speed Info
Ambient temperature signal Air conditioning amplifier assembly
·

ECM

·

Combination meter assembly

·

Engine stop and start ECU


·

Clearance warning ECU assembly

·

Forward recognition camera

·

Main body ECU (multiplex network body ECU)

·

4 wheel drive control ECU (4WD control ECU)


Air Conditioner Ambient Temp Sensor
Engine Ambient Temp for A/C
Engine Ambient Temperature
Stop and Start Ambient Temperature
Combination Meter Ambient Temperature
Steering angle sensor signal Steering sensor
·

Master cylinder solenoid (skid control ECU) (Except 2TR)

·

Blind spot monitor sensor LH

·

Engine stop and start ECU

·

Suspension control ECU

·

Power steering ECU assembly

·

Stabilizer control ECU

·

Forward recognition camera


·

Radio and display receiver assembly (EMVN ECU)

·

Airbag sensor assembly

·

ECM

·

No. 1 headlight ECU sub-assembly LH

·

Parking assist ECU

·

Combination meter assembly


ABS/VSC/TRC
·

Steering Angle Sensor

·

Steering Angle Value


Blind Spot Monitor Master Steering Angle
Radar Cruise2 Steering Angle Signal
Air Suspension Steering Angle
KDSS Steering Angle
PPS Steering Angle
Stop and Start Steering Angle
Door courtesy signal Main body ECU (multiplex network body ECU) Engine stop and start ECU
·

Radio and display receiver assembly (EMVN ECU)

·

Certification ECU (smart key ECU assembly)

·

Combination meter assembly*1

·

Master cylinder solenoid (skid control ECU)

·

Brake actuator assembly (skid control ECU)

·

Suspension control ECU

·

Parking assist ECU

·

Telephone transceiver assembly


Main Body
·

D Door Courtesy SW

·

P-Door Courtesy SW

·

RL Door Courtesy SW

·

RR Door Courtesy SW


Stop and Start Driver Courtesy Switch Signal

·

*1: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter assembly.

·

*2: The combination meter assembly receives a vehicle speed signal from the skid control ECU and sends the signal to other ECUs.

·

*3: According to the display on the GTS, read the Data List.

-

Enter the following menus: Body Electrical / Combination Meter / Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Power Source Control / Data List.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DATA LIST / ACTIVE TEST

-
-

Enter the following menus: Powertrain / Radar Cruise2 / Data List.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Main Body / Data List.

for Halogen Headlight: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST

for LED Headlight: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Chassis / PPS / Data List.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ VSC)>DATA LIST / ACTIVE TEST

-

Enter the following menus: Powertrain / Stop and Start / Data List.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Blind Spot Monitor Master / Data List.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Starting Control / Data List.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST

-
-

Enter the following menus: Body Electrical / Navigation System / Data List.

w/ Audio and Visual System (for Radio and Display Type): Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DATA LIST / ACTIVE TEST

w/ Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Powertrain / Four Wheel Drive / Data List.

Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Telematics / Data List.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DATA LIST / ACTIVE TEST


·

*4: for Manual Transmission (RA61F)