Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2021.06
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 2 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area

*1: w/ Entry and Start System

*2: for 1GR-FE, 1GD-FTV, 2TR-FE with Pre-collision System

*3: for 2TR-FE without Pre-collision System

*4: w/ Tire Pressure Warning System

*5: for LED Headlight

*6: w/ Stop and Start System

There is no resistance between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch bus line

·

Central gateway ECU (network gateway ECU)

·

ECM

·

Air conditioning amplifier assembly

·

Certification ECU (smart key ECU assembly)*1

·

Power steering ECU assembly

·

Master cylinder solenoid (skid control ECU)*2

·

Brake actuator assembly (skid control ECU)*3

·

Airbag sensor assembly

·

Steering sensor

·

Combination meter assembly

·

Tire pressure warning ECU and receiver*4

·

Main body ECU (multiplex network body ECU)

·

Engine stop and start ECU*6

·

No. 1 headlight ECU sub-assembly LH*5

·

No. 2 CAN junction connector

·

No. 6 CAN junction connector



WIRING DIAGRAM

for LHD


C448302E03
1.333,0.531 1.948,0.729 0.615,0.198 10 false G184 1.333,0.927 1.948,1.125 0.615,0.198 10 false G184 1.74,0.531 2.354,0.729 0.615,0.198 10 false G181 1.729,0.938 2.344,1.135 0.615,0.198 10 false G181 2.167,0.938 2.781,1.135 0.615,0.198 10 false G56 2.177,0.542 2.792,0.74 0.615,0.198 10 false G56 2.552,0.542 3.167,0.74 0.615,0.198 10 false G56 2.573,0.927 3.188,1.125 0.615,0.198 10 false G56 2.573,0.76 3.188,0.958 0.615,0.198 10 false 25*5 2.573,0.344 3.188,0.542 0.615,0.198 10 false 31*5 2.156,0.333 2.771,0.531 0.615,0.198 10 false 32*4 2.156,0.75 2.771,0.948 0.615,0.198 10 false 31*4 1.781,0.75 2.396,0.948 0.615,0.198 10 false 14*3 1.75,0.333 2.365,0.531 0.615,0.198 10 false 13*3 1.385,0.74 2,0.938 0.615,0.198 10 false 28*1 1.365,0.344 1.979,0.542 0.615,0.198 10 false 17*1 3.531,0.448 4.146,0.646 0.615,0.198 10 false 10 3.552,0.844 4.167,1.042 0.615,0.198 10 false 20 0.917,1.042 1.531,1.24 0.615,0.198 10 false CANL 0.885,0.427 1.5,0.625 0.615,0.198 10 false CANH 0.688,1.385 1.302,1.583 0.615,0.198 10 false ECM 4.313,0.448 4.927,0.646 0.615,0.198 10 false 6 4.292,0.844 4.906,1.042 0.615,0.198 10 false 16 5.094,1.104 5.708,1.302 0.615,0.198 10 false G229 5.094,1.26 7.031,1.688 1.938,0.427 10 false Central Gateway ECU (Network Gateway ECU) 5.688,0.521 6.302,0.719 0.615,0.198 10 false CA4H 5.688,0.938 6.302,1.135 0.615,0.198 10 false CA4L 5.417,0.448 6.031,0.646 0.615,0.198 10 false 18 5.427,0.854 6.042,1.052 0.615,0.198 10 false 17 0.146,3.021 0.76,3.219 0.615,0.198 10 false G215 0.156,3.208 1.948,3.625 1.792,0.417 10 false Certification ECU (Smart Key ECU Assembly)*2 0.865,2.438 1.479,2.635 0.615,0.198 10 false CANH 0.885,2.833 1.5,3.031 0.615,0.198 10 false CANL 1.354,2.729 1.969,2.927 0.615,0.198 10 false 8 1.375,2.323 1.99,2.521 0.615,0.198 10 false 7 3.552,2.323 4.167,2.521 0.615,0.198 10 false 3 3.531,2.708 4.146,2.906 0.615,0.198 10 false 13 4.271,2.719 4.885,2.917 0.615,0.198 10 false 12 5.448,2.333 6.063,2.531 0.615,0.198 10 false 13 4.281,2.302 4.896,2.5 0.615,0.198 10 false 2 5.438,2.75 6.052,2.948 0.615,0.198 10 false 22 5.688,2.448 6.302,2.646 0.615,0.198 10 false CANH 5.688,2.813 6.302,3.01 0.615,0.198 10 false CANL 5.24,3.188 6.958,3.542 1.719,0.354 10 false Airbag Sensor Assembly 5.25,3 5.865,3.198 0.615,0.198 10 false G1 0.208,4.76 0.823,4.958 0.615,0.198 10 false G46 0.219,4.948 2.646,5.333 2.427,0.385 10 false Power Steering ECU Assembly 0.865,4.156 1.479,4.354 0.615,0.198 10 false CANH 0.885,4.563 1.5,4.76 0.615,0.198 10 false CANL 1.333,4.052 1.948,4.25 0.615,0.198 10 false 1 1.354,4.458 1.969,4.656 0.615,0.198 10 false 2 3.583,4.073 4.198,4.271 0.615,0.198 10 false 8 3.531,4.448 4.146,4.646 0.615,0.198 10 false 18 4.344,4.063 4.958,4.26 0.615,0.198 10 false 7 4.292,4.469 4.906,4.667 0.615,0.198 10 false 17 5.438,4.063 6.052,4.26 0.615,0.198 10 false 11 5.417,4.469 6.031,4.667 0.615,0.198 10 false 12 5.677,4.146 6.292,4.344 0.615,0.198 10 false CANH 5.688,4.563 6.302,4.76 0.615,0.198 10 false CANL 5.302,4.979 6.938,5.365 1.635,0.385 10 false Air Conditioning Amplifier Assembly 5.302,4.771 5.917,4.969 0.615,0.198 10 false G25 4.292,6.031 4.906,6.229 0.615,0.198 10 false 9 4.292,6.438 4.906,6.635 0.615,0.198 10 false 19 5.281,6.729 5.896,6.927 0.615,0.198 10 false G205 5.417,6.917 6.708,7.313 1.292,0.396 10 false Steering Sensor 5.698,6.125 6.313,6.323 0.615,0.198 10 false CANH 5.719,6.51 6.333,6.708 0.615,0.198 10 false CANL 5.5,6.052 6.115,6.25 0.615,0.198 10 false 3 5.49,6.438 6.104,6.635 0.615,0.198 10 false 2 3.292,6.75 3.906,6.948 0.615,0.198 10 false G290 3.302,6.948 4.542,7.313 1.24,0.365 10 false No. 6 CAN Junction Connector 0.115,6.927 1.479,7.156 1.365,0.229 10 false *1: for 1GD-FTV 0.094,7.656 1.458,7.885 1.365,0.229 10 false *3: for 2TR-FE 0.094,8.031 2.813,8.385 2.719,0.354 10 false *4: for 1GR-FE with Manual Transmission 0.094,8.417 3.302,8.75 3.208,0.333 10 false *5: for 1GR-FE with Automatic Transmission 0.104,7.302 2,7.656 1.896,0.354 10 false *2: w/ Entry and Start System 3.583,6.031 4.198,6.229 0.615,0.198 10 false 1 3.531,6.438 4.146,6.635 0.615,0.198 10 false 11

C463935E01
3.25,0.385 3.406,0.583 0.156,0.198 10 false 1 3.188,0.792 3.417,1 0.229,0.208 10 false 11 3.24,1.667 3.552,1.885 0.313,0.219 10 false 7 3.177,2.073 3.531,2.344 0.354,0.271 10 false 17 0.219,2.281 0.51,2.479 0.292,0.198 10 false R41 0.198,2.469 3,2.792 2.802,0.323 10 false Tire Pressure Warning ECU and Receiver*1 0.844,1.781 1.365,2 0.521,0.219 10 false CANH 0.865,2.135 1.385,2.354 0.521,0.219 10 false CANL 1.333,1.667 1.656,1.865 0.323,0.198 10 false 9 1.323,2.01 1.573,2.208 0.25,0.198 10 false 10 0.208,5.083 0.5,5.281 0.292,0.198 10 false A6 0.135,3.813 2.052,4.229 1.917,0.417 10 false Master Cylinder Solenoid (Skid Control ECU)*2 0.854,3.125 1.375,3.344 0.521,0.219 10 false CANH 0.885,3.5 1.406,3.719 0.521,0.219 10 false CANL 1.323,3.052 1.677,3.292 0.354,0.24 10 false 11 1.344,3.375 1.698,3.615 0.354,0.24 10 false 25 3.167,3.031 3.521,3.271 0.354,0.24 10 false 10 3.188,3.396 3.542,3.635 0.354,0.24 10 false 20 3.927,3.042 4.281,3.281 0.354,0.24 10 false 9 3.927,3.396 4.281,3.635 0.354,0.24 10 false 19 3.927,5.802 4.281,6.042 0.354,0.24 10 false 8 3.906,6.208 4.26,6.448 0.354,0.24 10 false 18 5.688,3.063 5.958,3.25 0.271,0.188 10 false 14 5.688,3.365 5.917,3.573 0.229,0.208 10 false 13 5.948,3.125 6.469,3.344 0.521,0.219 10 false CANH 5.938,3.438 6.458,3.656 0.521,0.219 10 false CANL 5.448,3.719 5.969,3.938 0.521,0.219 10 false G218 5.417,3.906 7.094,4.406 1.677,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 5.188,6.51 5.708,6.729 0.521,0.219 10 false G304 5.198,6.708 7.115,7.042 1.917,0.333 10 false Combination Meter Assembly 5.917,5.792 6.438,6.01 0.521,0.219 10 false CANH 5.906,6.448 6.427,6.667 0.521,0.219 10 false CANL 5.667,6.198 5.896,6.406 0.229,0.208 10 false 39 5.667,5.792 5.896,6 0.229,0.208 10 false 40 2.969,7.865 3.49,8.083 0.521,0.219 10 false G286 3.052,8.073 5.323,8.281 2.271,0.208 10 false No. 2 CAN Junction Connector 0.135,7.094 3.104,7.375 2.969,0.281 10 false *1: w/ Tire Pressure Warning System 0.146,7.5 2.583,7.854 2.438,0.354 10 false *2: for 1GR-FE, 1GD-FTV, 2TR-FE with Pre-collision System 0.156,6.469 0.677,6.688 0.521,0.219 10 false A130 0.156,6.635 2.854,6.958 2.698,0.323 10 false No. 1 Headlight ECU Sub-assembly LH*3 3.24,5.823 3.594,6.063 0.354,0.24 10 false 4 3.177,6.219 3.531,6.458 0.354,0.24 10 false 14 0.146,8.063 1.646,8.313 1.5,0.25 10 false *3: for LED Headlight 0.833,5.896 1.354,6.115 0.521,0.219 10 false CANH 0.854,6.302 1.375,6.521 0.521,0.219 10 false CANL 1.333,5.823 1.688,6.063 0.354,0.24 10 false 24 1.344,6.208 1.698,6.448 0.354,0.24 10 false 23 0.156,3.625 0.448,3.823 0.292,0.198 10 false A7 0.156,5.302 3.167,5.656 3.01,0.354 10 false Brake Actuator Assembly (Skid Control ECU)*5 0.865,4.604 1.385,4.823 0.521,0.219 10 false CANH 0.896,4.958 1.417,5.177 0.521,0.219 10 false CANL 1.333,4.521 1.688,4.76 0.354,0.24 10 false 25 1.323,4.885 1.677,5.125 0.354,0.24 10 false 14 0.146,8.448 2.729,8.698 2.583,0.25 10 false *4: w/ Stop and Start System 2.552,8.458 5.938,8.698 3.385,0.24 10 false *5: for 2TR-FE without Pre-collision System 5.302,8.063 7.125,8.396 1.823,0.333 10 false Engine Stop and Start ECU*4 5.302,7.875 5.823,8.094 0.521,0.219 10 false G314 5.688,7.26 6.208,7.479 0.521,0.219 10 false 13 5.688,7.615 5.958,7.802 0.271,0.188 10 false 14 3.927,7.26 4.448,7.479 0.521,0.219 10 false 5 3.906,7.635 4.427,7.854 0.521,0.219 10 false 15 5.927,7.344 6.448,7.563 0.521,0.219 10 false CANH 5.938,7.667 6.458,7.885 0.521,0.219 10 false CANL


for RHD


C463936E01
1.333,0.458 1.948,0.656 0.615,0.198 10 false G184 1.333,0.865 1.948,1.063 0.615,0.198 10 false G184 1.771,0.458 2.385,0.656 0.615,0.198 10 false G56 1.781,0.854 2.396,1.052 0.615,0.198 10 false G56 1.76,0.667 2.375,0.865 0.615,0.198 10 false 25*2 1.802,0.25 2.417,0.448 0.615,0.198 10 false 31*2 1.385,0.667 2,0.865 0.615,0.198 10 false 28*1 1.365,0.24 1.979,0.438 0.615,0.198 10 false 17*1 3.531,0.365 4.146,0.563 0.615,0.198 10 false 10 3.552,0.75 4.167,0.948 0.615,0.198 10 false 20 0.875,0.979 1.49,1.177 0.615,0.198 10 false CANL 0.875,0.354 1.49,0.552 0.615,0.198 10 false CANH 0.604,1.281 1.219,1.479 0.615,0.198 10 false ECM 4.292,0.344 4.906,0.542 0.615,0.198 10 false 6 4.281,0.729 4.896,0.927 0.615,0.198 10 false 16 5.052,1.073 5.667,1.271 0.615,0.198 10 false G229 5.063,1.229 7,1.656 1.938,0.427 10 false Central Gateway ECU (Network Gateway ECU) 5.677,0.438 6.292,0.635 0.615,0.198 10 false CA4H 5.708,0.833 6.323,1.031 0.615,0.198 10 false CA4L 5.406,0.354 6.021,0.552 0.615,0.198 10 false 18 5.448,0.76 6.063,0.958 0.615,0.198 10 false 17 0.125,2.781 0.74,2.979 0.615,0.198 10 false G215 0.135,2.969 1.698,3.344 1.563,0.375 10 false Certification ECU (Smart Key ECU Assembly)*3 0.833,2.281 1.448,2.479 0.615,0.198 10 false CANH 0.865,2.688 1.479,2.885 0.615,0.198 10 false CANL 1.365,2.552 1.979,2.75 0.615,0.198 10 false 8 1.375,2.146 1.99,2.344 0.615,0.198 10 false 7 3.542,2.167 4.156,2.365 0.615,0.198 10 false 3 3.49,2.552 4.104,2.75 0.615,0.198 10 false 13 5.438,4.229 6.052,4.427 0.615,0.198 10 false 10 5.51,3.833 6.125,4.031 0.615,0.198 10 false 9 5.708,4.354 6.323,4.552 0.615,0.198 10 false CANL 5.677,3.958 6.292,4.156 0.615,0.198 10 false CANH 5.281,4.479 5.896,4.677 0.615,0.198 10 false R41 5.219,4.677 6.938,5.115 1.719,0.438 10 false Tire Pressure Warning ECU and Receiver*4 3.552,3.844 4.167,4.042 0.615,0.198 10 false 4 3.521,4.229 4.135,4.427 0.615,0.198 10 false 14 4.292,3.854 4.906,4.052 0.615,0.198 10 false 5 4.271,4.208 4.885,4.406 0.615,0.198 10 false 15 1.333,3.833 1.948,4.031 0.615,0.198 10 false 24 1.323,4.219 1.938,4.417 0.615,0.198 10 false 23 0.115,4.5 0.729,4.698 0.615,0.198 10 false A130 0.125,4.677 1.49,5.031 1.365,0.354 10 false No. 1 Headlight ECU Sub-assembly LH*5 0.844,3.948 1.458,4.146 0.615,0.198 10 false CANH 0.885,4.323 1.5,4.521 0.615,0.198 10 false CANL 4.313,5.5 4.927,5.698 0.615,0.198 10 false 7 4.292,5.885 4.906,6.083 0.615,0.198 10 false 17 5.438,5.49 6.052,5.688 0.615,0.198 10 false 11 5.427,5.896 6.042,6.094 0.615,0.198 10 false 12 5.698,5.615 6.313,5.813 0.615,0.198 10 false CANH 5.688,6.031 6.302,6.229 0.615,0.198 10 false CANL 5.323,6.313 6.958,6.698 1.635,0.385 10 false Air Conditioning Amplifier Assembly 5.313,6.167 5.927,6.365 0.615,0.198 10 false G25 3.229,7.354 3.844,7.552 0.615,0.198 10 false G290 3.25,7.552 5.375,7.917 2.125,0.365 10 false No. 6 CAN Junction Connector 0.115,6.844 1.479,7.073 1.365,0.229 10 false *1: for 1GD-FTV 0.135,7.219 1.5,7.448 1.365,0.229 10 false *2: for 1GR-FE 0.125,7.604 2.021,7.958 1.896,0.354 10 false *3: w/ Entry and Start System 0.115,8.385 2.438,8.615 2.323,0.229 10 false *5: for LHD Headlight 0.104,8.01 2.438,8.323 2.333,0.313 10 false *4: w/ Tire Pressure Warning System 3.563,6.635 4.177,6.833 0.615,0.198 10 false 1 3.521,7.01 4.135,7.208 0.615,0.198 10 false 11

C382807E11
3.25,0.438 3.406,0.635 0.156,0.198 10 false 1 3.188,0.854 3.417,1.063 0.229,0.208 10 false 11 3.958,0.438 4.115,0.635 0.156,0.198 10 false 2 3.917,0.823 4.146,1.031 0.229,0.208 10 false 12 5.698,0.469 5.854,0.667 0.156,0.198 10 false 3 5.698,0.833 5.854,1.031 0.156,0.198 10 false 2 5.917,0.563 6.438,0.781 0.521,0.219 10 false CANH 5.917,0.958 6.438,1.177 0.521,0.219 10 false CANL 5.26,1.135 5.781,1.354 0.521,0.219 10 false G205 5.292,1.292 6.906,1.75 1.615,0.458 10 false Steering Sensor 3.948,2.198 4.104,2.396 0.156,0.198 10 false 3 3.938,2.625 4.156,2.823 0.219,0.198 10 false 13 5.625,2.24 5.875,2.438 0.25,0.198 10 false 13 5.635,2.646 5.885,2.865 0.25,0.219 10 false 22 5.927,2.344 6.448,2.563 0.521,0.219 10 false CANH 5.948,2.719 6.469,2.938 0.521,0.219 10 false CANL 5.406,2.938 5.927,3.156 0.521,0.219 10 false G1 5.406,3.104 7.052,3.344 1.646,0.24 10 false Airbag Sensor Assembly 3.177,2.219 3.49,2.438 0.313,0.219 10 false 7 3.135,2.667 3.49,2.938 0.354,0.271 10 false 17 0.229,2.969 0.521,3.167 0.292,0.198 10 false G46 0.229,3.146 2.25,3.51 2.021,0.365 10 false Power Steering ECU Assembly 0.844,2.375 1.365,2.594 0.521,0.219 10 false CANH 0.865,2.75 1.385,2.969 0.521,0.219 10 false CANL 1.344,2.24 1.5,2.438 0.156,0.198 10 false 1 1.344,2.656 1.594,2.854 0.25,0.198 10 false 2 0.219,4.729 0.51,4.927 0.292,0.198 10 false A7 0.208,4.917 1.802,5.323 1.594,0.406 10 false Master Cylinder Solenoid (Skid Control ECU) 0.813,4.156 1.333,4.375 0.521,0.219 10 false CANH 0.823,4.531 1.344,4.75 0.521,0.219 10 false CANL 1.354,4.01 1.708,4.25 0.354,0.24 10 false 11 1.354,4.427 1.708,4.667 0.354,0.24 10 false 25 3.156,4.031 3.51,4.271 0.354,0.24 10 false 10 3.156,4.438 3.51,4.677 0.354,0.24 10 false 20 3.958,4.031 4.313,4.271 0.354,0.24 10 false 9 3.938,4.417 4.292,4.656 0.354,0.24 10 false 19 3.927,5.979 4.281,6.219 0.354,0.24 10 false 8 3.938,6.375 4.292,6.615 0.354,0.24 10 false 18 5.656,4.042 5.885,4.25 0.229,0.208 10 false 14 5.656,4.448 5.885,4.656 0.229,0.208 10 false 13 5.938,4.125 6.458,4.344 0.521,0.219 10 false CANH 5.958,4.552 6.479,4.771 0.521,0.219 10 false CANL 5.354,4.75 5.875,4.969 0.521,0.219 10 false G218 5.354,4.906 7.031,5.406 1.677,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 5.458,6.75 5.979,6.969 0.521,0.219 10 false G304 5.479,6.896 6.646,7.375 1.167,0.479 10 false Combination Meter Assembly 5.938,5.948 6.458,6.167 0.521,0.219 10 false CANH 5.938,6.604 6.458,6.823 0.521,0.219 10 false CANL 5.656,6.365 5.885,6.573 0.229,0.208 10 false 39 5.667,5.969 5.896,6.177 0.229,0.208 10 false 40 2.979,6.677 3.5,6.896 0.521,0.219 10 false G286 3,6.844 4.313,7.292 1.313,0.448 10 false No. 2 CAN Junction Connector 0.188,8.167 3.156,8.448 2.969,0.281 10 false *: w/ Stop and Start System 0.125,6.656 0.646,6.875 0.521,0.219 10 false G314 0.125,6.854 1.958,7.25 1.833,0.396 10 false Engine Stop and Start ECU* 3.198,6.01 3.552,6.25 0.354,0.24 10 false 5 3.146,6.406 3.5,6.646 0.354,0.24 10 false 15 0.802,6.115 1.323,6.333 0.521,0.219 10 false CANH 0.813,6.479 1.333,6.698 0.521,0.219 10 false CANL 1.344,5.979 1.698,6.219 0.354,0.24 10 false 13 1.354,6.406 1.708,6.646 0.354,0.24 10 false 14


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable to the negative (-) battery terminal.


b.

Disconnect the No. 6 CAN junction connector.

C448423C01
0.229,1.781 0.677,2.042 0.448,0.26 5.302,1.031 5.75,1.292 0.448,0.26 0.844,1.385 1.01,1.385 1.01,1.385 1.01,1.885 true 1.083,1.146 1.25,1.146 1.25,1.146 1.25,1.896 true 1.323,0.948 1.49,0.948 1.49,0.948 1.49,1.865 true 1.552,0.729 1.719,0.729 1.719,0.729 1.719,1.896 true 1.802,0.469 1.969,0.469 1.969,0.469 1.969,1.885 true 2.354,0.479 2.188,0.479 2.188,0.479 2.188,1.896 true 2.615,0.729 2.448,0.729 2.448,0.729 2.448,1.896 true 2.854,0.979 2.688,0.979 2.688,0.979 2.688,1.896 true 3.104,1.167 2.938,1.167 2.938,1.167 2.938,1.917 true 3.344,1.427 3.177,1.427 3.177,1.427 3.177,1.927 true 3.344,2.521 3.177,2.521 3.177,2.521 3.177,2.104 true 3.104,2.75 2.938,2.75 2.938,2.75 2.938,2.083 true 2.865,3.042 2.698,3.042 2.698,3.042 2.698,2.125 true 2.625,3.26 2.458,3.26 2.458,3.26 2.458,2.094 true 2.385,3.448 2.219,3.448 2.219,3.448 2.219,2.115 true 1.802,3.448 1.969,3.448 1.969,3.448 1.969,2.115 true 1.563,3.271 1.729,3.271 1.729,3.271 1.729,2.104 true 1.323,3.115 1.49,3.115 1.49,3.115 1.49,2.115 true 1.073,2.938 1.24,2.938 1.24,2.938 1.24,2.104 true 0.854,2.771 1.021,2.771 1.021,2.771 1.021,2.104 true 6.125,2.552 5.958,2.552 5.958,2.552 5.958,2.135 true 0.177,0.531 0.49,0.729 0.313,0.198 10 false *a 4.438,0.833 4.75,1.031 0.313,0.198 10 false *b 0.271,1.833 0.625,2.031 0.354,0.198 10 false G290 0.313,1.292 0.917,1.531 0.604,0.24 10 false CANH*c 0.542,1.063 1.146,1.302 0.604,0.24 10 false CANH*d 0.771,0.844 1.375,1.083 0.604,0.24 10 false CANH*e 1.031,0.656 1.635,0.896 0.604,0.24 10 false CANH*f 1.24,0.385 1.844,0.625 0.604,0.24 10 false CANH*g 2.406,0.406 3.01,0.646 0.604,0.24 10 false CANH*h 2.667,0.667 3.271,0.906 0.604,0.24 10 false CANH*i 2.917,0.906 3.521,1.146 0.604,0.24 10 false CANH*j 3.167,1.083 3.771,1.323 0.604,0.24 10 false CANH*k 3.385,1.333 3.99,1.573 0.604,0.24 10 false CANH*l 0.344,2.688 0.948,2.927 0.604,0.24 10 false CANL*c 0.563,2.854 1.167,3.094 0.604,0.24 10 false CANL*d 0.813,3.031 1.417,3.271 0.604,0.24 10 false CANL*e 1.063,3.198 1.667,3.438 0.604,0.24 10 false CANL*f 1.292,3.365 1.896,3.604 0.604,0.24 10 false CANL*g 2.438,3.375 3.042,3.615 0.604,0.24 10 false CANL*h 2.677,3.177 3.281,3.417 0.604,0.24 10 false CANL*i 2.927,2.958 3.531,3.198 0.604,0.24 10 false CANL*j 3.167,2.667 3.771,2.906 0.604,0.24 10 false CANL*k 3.396,2.427 4,2.667 0.604,0.24 10 false CANL*l 6.188,2.49 6.604,2.729 0.417,0.24 10 false BAT 5.375,1.083 5.906,1.281 0.531,0.198 10 false G317
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b Front view of DLC3
*c to No. 2 CAN Junction Connector *d to Airbag Sensor Assembly (for LHD)
*e to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *f to No. 1 Headlight ECU Sub-assembly LH (for RHD with LED Headlight)
*g to Tire Pressure Warning ECU and Receiver (for RHD with Tire Pressure Warning System) *h to Central Gateway ECU (Network Gateway ECU)
*i to Air Conditioning Amplifier Assembly *j to Power Steering ECU Assembly (for LHD)
*k to Steering Sensor (for LHD) *l to ECM



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Entry and Start System

*2: for RHD with LED Headlight

*3: for RHD with Tire Pressure Warning System

*4: for LHD

G290-1 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 2 CAN junction connector
G290-11 (CANL) - G317-16 (BAT)
G290-2 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag sensor assembly*4
G290-12 (CANL) - G317-16 (BAT)
G290-3 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Certification ECU (smart key ECU assembly)*1
G290-13 (CANL) - G317-16 (BAT)
G290-4 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 1 headlight ECU sub-assembly LH*2
G290-14 (CANL) - G317-16 (BAT)
G290-5 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Tire pressure warning ECU and receiver*3
G290-15 (CANL) - G317-16 (BAT)
G290-6 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
G290-16 (CANL) - G317-16 (BAT)
G290-7 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Air conditioning amplifier assembly
G290-17 (CANL) - G317-16 (BAT)
G290-8 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Power steering ECU assembly*4
G290-18 (CANL) - G317-16 (BAT)
G290-9 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Steering sensor*4
G290-19 (CANL) - G317-16 (BAT)
G290-10 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
G290-20 (CANL) - G317-16 (BAT)



Result:
Result Proceed to
OK A
NG (No. 2 CAN junction connector CAN main wire) B
NG (Central gateway ECU [network gateway ECU] CAN branch wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

4.CONNECT CONNECTOR

D

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the G290 No. 6 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.

C448423C02
0.229,1.781 0.677,2.042 0.448,0.26 5.25,1.042 5.698,1.302 0.448,0.26 0.844,1.385 1.01,1.385 1.01,1.385 1.01,1.885 true 1.083,1.146 1.25,1.146 1.25,1.146 1.25,1.896 true 1.323,0.948 1.49,0.948 1.49,0.948 1.49,1.865 true 2.615,0.729 2.448,0.729 2.448,0.729 2.448,1.896 true 2.854,0.979 2.688,0.979 2.688,0.979 2.688,1.896 true 3.104,1.167 2.938,1.167 2.938,1.167 2.938,1.917 true 3.344,1.427 3.177,1.427 3.177,1.427 3.177,1.927 true 3.344,2.521 3.177,2.521 3.177,2.521 3.177,2.104 true 3.104,2.75 2.938,2.75 2.938,2.75 2.938,2.083 true 2.865,3.042 2.698,3.042 2.698,3.042 2.698,2.125 true 2.625,3.26 2.458,3.26 2.458,3.26 2.458,2.094 true 1.323,3.115 1.49,3.115 1.49,3.115 1.49,2.115 true 1.073,2.938 1.24,2.938 1.24,2.938 1.24,2.104 true 0.854,2.771 1.021,2.771 1.021,2.771 1.021,2.104 true 6.135,2.563 5.969,2.563 5.969,2.563 5.969,2.146 true 1.563,0.688 1.729,0.688 1.729,0.688 1.729,1.906 true 1.552,3.385 1.719,3.385 1.719,3.385 1.719,2.104 true 1.781,0.479 1.948,0.479 1.948,0.479 1.948,1.917 true 1.792,3.583 1.958,3.583 1.958,3.583 1.958,2.104 true 0.177,0.531 0.49,0.729 0.313,0.198 10 false *a 4.438,0.833 4.75,1.031 0.313,0.198 10 false *b 0.271,1.833 0.625,2.031 0.354,0.198 10 false G286 0.313,1.292 0.917,1.531 0.604,0.24 10 false CANH*c 0.542,1.063 1.146,1.302 0.604,0.24 10 false CANH*d 0.771,0.844 1.375,1.083 0.604,0.24 10 false CANH*e 1.25,0.365 1.854,0.604 0.604,0.24 10 false CANH*g 2.677,0.635 3.281,0.875 0.604,0.24 10 false CANH*h 2.906,0.896 3.51,1.135 0.604,0.24 10 false CANH*i 3.177,1.094 3.781,1.333 0.604,0.24 10 false CANH*j 0.344,2.688 0.948,2.927 0.604,0.24 10 false CANL*c 0.563,2.854 1.167,3.094 0.604,0.24 10 false CANL*d 0.813,3.031 1.417,3.271 0.604,0.24 10 false CANL*e 1.292,3.51 1.896,3.75 0.604,0.24 10 false CANL*g 2.688,3.208 3.292,3.448 0.604,0.24 10 false CANL*h 2.927,2.979 3.531,3.219 0.604,0.24 10 false CANL*i 3.156,2.698 3.76,2.938 0.604,0.24 10 false CANL*j 6.208,2.521 6.625,2.76 0.417,0.24 10 false BAT 5.292,1.083 5.646,1.281 0.354,0.198 10 false G317 1.031,3.292 1.635,3.531 0.604,0.24 10 false CANL*f 1.031,0.625 1.635,0.865 0.604,0.24 10 false CANH*f 3.438,1.375 4.042,1.615 0.604,0.24 10 false CANH*k 3.406,2.448 4.01,2.688 0.604,0.24 10 false CANL*k
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3
*c to No. 6 CAN Junction Connector *d to Steering Sensor (for RHD)
*e to Airbag Sensor Assembly (for RHD) *f to No. 1 Headlight ECU Sub-assembly LH (for LHD with LED Headlight)
*g to Engine Stop and Start ECU (w/ Stop and Start System) *h
·

to Tire Pressure Warning ECU and Receiver (for LHD with Tire Pressure Warning System)

·

to Power Steering ECU Assembly (for RHD)


*i to Combination Meter Assembly *j to Main Body ECU (Multiplex Network Body ECU)
*k
·

to Master Cylinder Solenoid (Skid Control ECU) (for 1GR-FE, 1GD-FTV, 2TR-FE with Pre-collision System)

·

to Brake Actuator Assembly (Skid Control ECU) (for 2TR-FE without Pre-collision System)


- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: for LHD with LED Headlight

*2: for LHD with Tire Pressure Warning System

*3: for RHD

*4: for 1GR-FE, 1GD-FTV, 2TR-FE with Pre-collision System

*5: for 2TR-FE without Pre-collision System

*6: w/ Stop and Start System

G286-1 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 6 CAN junction connector
G286-11 (CANL) - G317-16 (BAT)
G286-2 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Steering sensor*3
G286-12 (CANL) - G317-16 (BAT)
G286-3 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag sensor assembly*3
G286-13 (CANL) - G317-16 (BAT)
G286-4 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 1 headlight ECU sub-assembly LH*1
G286-14 (CANL) - G317-16 (BAT)
G286-5 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Engine stop and start ECU*6
G286-15 (CANL) - G317-16 (BAT)
G286-7 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
·

Tire pressure warning ECU and receiver*2

·

Power steering ECU assembly*3


G286-17 (CANL) - G317-16 (BAT)
G286-8 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination meter assembly
G286-18 (CANL) - G317-16 (BAT)
G286-9 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Main body ECU (multiplex network body ECU)
G286-19 (CANL) - G317-16 (BAT)
G286-10 (CANH) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
·

Master cylinder solenoid (skid control ECU)*4

·

Brake actuator assembly (skid control ECU)*5


G286-20 (CANL) - G317-16 (BAT)



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
4.CONNECT CONNECTOR
a.

Reconnect the G290 No. 6 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)
a.
C448424C01
1.479,0.26 2.042,0.521 0.563,0.26 1.438,2.542 1.969,2.781 0.531,0.24 1.646,1.5 1.51,2.115 1.51,2.115 1.323,2.115 true 2.583,4.198 2.417,4.198 2.417,4.198 2.417,3.635 true 2.115,2.104 1.948,2.104 1.948,2.104 1.792,1.469 true 1.573,0.292 2.188,0.49 0.615,0.198 10 false G229 1.542,2.573 2.156,2.771 0.615,0.198 10 false G317 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 2.156,2.031 2.771,2.229 0.615,0.198 10 false CA4H 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 0.917,2.031 1.531,2.229 0.615,0.198 10 false CA4L 2.656,4.125 3.271,4.323 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-18 (CA4H) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G229-17 (CA4L) - G317-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
a.

Reconnect the wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU


c.
C447912C03
1.448,0.25 1.917,0.51 0.469,0.26 1.427,2.427 1.958,2.698 0.531,0.271 2.365,3.604 2.031,4.271 2.031,4.271 1.865,4.271 true 1.677,1.146 1.49,1.792 1.49,1.792 1.302,1.792 true 1.771,1.146 2.104,1.865 2.104,1.865 2.323,1.865 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.115,2.198 0.427,2.396 0.313,0.198 10 false *b 1.542,0.302 2.031,0.552 0.49,0.25 10 false G229 1.531,2.469 2.021,2.719 0.49,0.25 10 false G317 2.396,1.781 2.885,2.031 0.49,0.25 10 false CA4L 1.573,4.188 2.063,4.438 0.49,0.25 10 false BAT 0.927,1.719 1.417,1.969 0.49,0.25 10 false CA4H
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-18 (CA4H) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G229-17 (CA4L) - G317-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPLACE CORRESPONDING ECU OR SENSOR