Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2021.06
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 3 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and +B when no resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)

*3: w/ Telematics System

·

No resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

·

No resistance exists between terminal 19 (CAYH) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 20 (CAYL) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.


·

Short to GND in CAN main bus line

·

Short to GND in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Radio and display receiver assembly (EMVN ECU)*1, *2

·

Telephone transceiver assembly*3

·

No. 5 CAN junction connector



WIRING DIAGRAM

C448450E06
0.208,1.01 0.667,1.208 0.458,0.198 10 false H93 0.198,1.198 2.531,1.531 2.333,0.333 10 false Radio and Display Receiver Assembly (EMVN ECU)*1, *2 0.854,0.438 1.313,0.635 0.458,0.198 10 false CANH 0.906,0.813 1.365,1.01 0.458,0.198 10 false CANL 1.385,0.344 1.844,0.542 0.458,0.198 10 false 13 1.385,0.74 1.844,0.938 0.458,0.198 10 false 14 0.146,3.781 0.646,3.979 0.5,0.198 10 false G333 0.917,3.25 1.375,3.448 0.458,0.198 10 false CANP 0.896,3.625 1.354,3.823 0.458,0.198 10 false CANN 1.375,3.135 1.833,3.333 0.458,0.198 10 false 25 1.375,3.521 1.833,3.719 0.458,0.198 10 false 26 0.135,3.969 3.063,4.333 2.927,0.365 10 false Telephone Transceiver Assembly*3 3.573,3.146 4.031,3.344 0.458,0.198 10 false 4 3.531,3.521 3.99,3.719 0.458,0.198 10 false 15 3.573,0.302 4.031,0.5 0.458,0.198 10 false 3 3.5,0.729 3.958,0.927 0.458,0.198 10 false 14 4.51,0.313 4.969,0.51 0.458,0.198 10 false 1 4.5,0.729 4.958,0.927 0.458,0.198 10 false 12 4.51,4.979 4.969,5.177 0.458,0.198 10 false 2 4.5,5.406 4.958,5.604 0.458,0.198 10 false 13 5.75,0.333 6.208,0.531 0.458,0.198 10 false 6 5.677,0.729 6.135,0.927 0.458,0.198 10 false 21 5.688,5.021 6.146,5.219 0.458,0.198 10 false 19 5.667,5.396 6.125,5.594 0.458,0.198 10 false 20 5.979,0.333 6.438,0.531 0.458,0.198 10 false CA3H 5.969,0.969 6.427,1.167 0.458,0.198 10 false CA3L 5.938,5.01 6.396,5.208 0.458,0.198 10 false CAYH 5.958,5.656 6.417,5.854 0.458,0.198 10 false CAYL 5.229,5.802 5.688,6 0.458,0.198 10 false G229 5.208,5.948 7.146,6.417 1.938,0.469 10 false Central Gateway ECU (Network Gateway ECU) 3,5.76 3.458,5.958 0.458,0.198 10 false G289 3.01,5.958 4.948,6.188 1.938,0.229 10 false No. 5 CAN Junction Connector 0.104,5.24 2.104,5.615 2,0.375 10 false *1: w/ Audio and Visual System (for Radio and Display Type) 0.104,5.906 2.5,6.188 2.396,0.281 10 false *2: w/ Navigation System 0.104,6.365 2.5,6.646 2.396,0.281 10 false *3: w/ Telematics System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from negative (-) battery terminal.


b.
C448475C02
0.156,1.208 0.594,1.448 0.438,0.24 0.198,3.406 0.656,3.656 0.458,0.25 0.698,0.604 0.865,0.604 0.865,0.604 0.865,1.302 true 0.854,0.385 1.021,0.385 1.021,0.385 1.021,1.302 true 1.365,0.135 1.198,0.135 1.198,0.135 1.198,1.302 true 1.531,0.385 1.365,0.385 1.365,0.385 1.365,1.302 true 0.698,2.104 0.865,2.104 0.865,2.104 0.865,1.635 true 0.865,2.313 1.031,2.313 1.031,2.313 1.031,1.646 true 1.365,2.552 1.198,2.552 1.198,2.552 1.198,1.635 true 1.531,2.344 1.365,2.344 1.365,2.344 1.365,1.677 true 2.063,4.313 1.896,4.313 1.896,4.313 1.635,3.49 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 0.156,2.708 0.469,2.906 0.313,0.198 10 false *b 0.208,1.25 0.573,1.448 0.365,0.198 10 false G289 0.271,3.448 0.635,3.646 0.365,0.198 10 false G317 0.156,0.51 0.771,0.719 0.615,0.208 10 false CANH*c 0.313,0.302 0.927,0.51 0.615,0.208 10 false CANH*d 1.417,0.073 2.031,0.281 0.615,0.208 10 false CANH*e 1.583,0.344 2.198,0.552 0.615,0.208 10 false CANH*f 0.167,2.01 0.781,2.219 0.615,0.208 10 false CANL*c 0.333,2.229 0.948,2.438 0.615,0.208 10 false CANL*d 1.417,2.469 2.031,2.677 0.615,0.208 10 false CANL*e 1.573,2.26 2.188,2.469 0.615,0.208 10 false CANL*f 2.125,4.25 2.74,4.458 0.615,0.208 10 false CG
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b Front view of DLC3
*c to Central Gateway ECU (Network Gateway ECU)
*d to Central Gateway ECU (Network Gateway ECU)
*e to Radio and Display Receiver Assembly (EMVN ECU) (w/ Audio and Visual System (for Radio and Display Type), w/ Navigation System)
*f to Telephone Transceiver Assembly (w/ Telematics System)


Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)

*3: w/ Telematics System

G289-1 (CANH) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G289-12 (CANL) - G317-4 (CG)
G289-2 (CANH) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G289-13 (CANL) - G317-4 (CG)
G289-3 (CANH) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly (EMVN ECU)*1, *2
G289-14 (CANL) - G317-4 (CG)
G289-4 (CANH) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Telematics transceiver*3
G289-15 (CANL) - G317-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the G289 No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)
a.
C448424C04
1.469,0.25 1.948,0.479 0.479,0.229 1.438,2.542 1.948,2.781 0.51,0.24 1.51,2.135 1.74,2.135 1.74,2.135 1.917,1.49 true 2.281,1.25 2.042,0.625 2.042,0.625 1.854,0.625 true 2.031,4.104 1.865,4.104 1.865,4.104 1.615,3.271 true 2.479,2.49 2.313,2.49 2.313,2.49 2.063,1.51 true 2.635,2.156 2.469,2.156 2.469,2.156 2.198,1.521 true 1.542,0.292 2.156,0.49 0.615,0.198 10 false G229 1.542,2.573 2.156,2.771 0.615,0.198 10 false G317 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 1.479,0.563 2.094,0.76 0.615,0.198 10 false CA3H 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 1.094,2.063 1.708,2.26 0.615,0.198 10 false CAYH 2.104,4.021 2.719,4.219 0.615,0.198 10 false CG 2.521,2.417 3.135,2.615 0.615,0.198 10 false CAYL 2.677,2.073 3.208,2.26 0.531,0.188 10 false CA3L
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-6 (CA3H) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-21 (CA3L) - G317-4 (CG)
G229-19 (CAYH) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-20 (CAYL) - G317-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.

Reconnect the wire harness connectors.


b.
C447917C06
1.5,2 1.969,2.26 0.469,0.26 1.5,0.083 1.969,0.344 0.469,0.26 1.656,2.583 1.281,2.167 1.281,2.167 1.156,2.167 true 1.396,0.771 1.167,0.333 1.167,0.333 1,0.333 true 1.406,0.896 1.188,1.479 1.188,1.479 1.021,1.479 true 1.573,0.125 2.031,0.323 0.458,0.198 10 false G229 1.583,2.052 2.042,2.25 0.458,0.198 10 false G317 0.625,0.271 1.083,0.469 0.458,0.198 10 false CA3H 0.688,1.417 1.146,1.615 0.458,0.198 10 false CA3L 0.896,2.094 1.354,2.292 0.458,0.198 10 false CG 0.104,0.115 0.563,0.313 0.458,0.198 10 false *a 0.167,2.083 0.625,2.281 0.458,0.198 10 false *b
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short to GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-6 (CA3H) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-21 (CA3L) - G317-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPLACE CORRESPONDING ECU OR SENSOR