Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2021.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P004518  Turbocharger/Supercharger Boost Control "A" Circuit Current Below Threshold  P004519  Turbocharger/Supercharger Boost Control "A" Circuit Current Above Threshold  P004600  Turbocharger/Supercharger Boost Control "A" Circuit Range/Performance  


DESCRIPTION

These DTCs indicate that the variable vane DC motor of the turbocharger is malfunctioning. The ECM monitors the variable vane DC motor current to detect an open or short in the variable vane DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.

The variable vane DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the variable vane DC motor in accordance with the driving conditions.

If the nozzle vane is stuck closed (Variable vane DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (Variable vane DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P004518 Turbocharger/Supercharger Boost Control "A" Circuit Current Below Threshold The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more.
(1 trip detection logic)
·

Short in variable vane DC motor (turbocharger nozzle vane control actuator) circuit

·

Turbocharger nozzle vane control actuator

·

Turbochargernozzle vane isstuck ormovement isirregular


Comes on DTC stored SAE Code: P0047
P004519 Turbocharger/Supercharger Boost Control "A" Circuit Current Above Threshold DC motor overcurrent is detected 25 times or more (0.4 seconds or more in real time).
(1 trip detection logic)
·

Open in variable vane DC motor (turbocharger nozzle vane control actuator) circuit

·

Turbocharger nozzle vane control actuator

·

Turbochargernozzle vane isstuck ormovement isirregular


Comes on DTC stored SAE Code: P0048
P004600 Turbocharger/Supercharger Boost Control "A" Circuit Range/Performance The difference between the target NV opening angle and the actual VN opening angle is 50% or greater for 65 seconds or more.
(1 trip detection logic)
·

Turbocharger nozzle vane control actuator

·

Turbocharger sub-assembly

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on DTC stored SAE Code: P0046

HINT:
·

If DTC P004518, P004519 and/or P004600 is stored due to the nozzle vane being stuck closed, the following symptom may appear:

-

Vehicle surge when driving with full load


·

If DTC P004518, P004519 and/or P004600 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

-

Lack of power

-

Vehicle surge or hesitation under light or medium load




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P004518
P004519
2 seconds after engine is started, race engine for 1 second
P004600 Maintain the Active Test "Activate the VN Turbo Open Bank 1" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.

WIRING DIAGRAM

A348538E88
0.729,1.844 1.188,2.042 0.458,0.198 10 false C175 0.729,2.052 2.719,2.24 1.99,0.188 10 false Variable Vane DC motor 1.76,0.521 2.219,0.719 0.458,0.198 10 false M+ 1.771,1.188 2.229,1.385 0.458,0.198 10 false M- 5.677,0.646 6.313,0.844 0.635,0.198 10 false VNM+ 5.677,1.292 6.292,1.479 0.615,0.188 10 false VNM- 5.979,1.844 6.438,2.042 0.458,0.198 10 false C151 5.99,2.01 6.448,2.208 0.458,0.198 10 false ECM 2.073,0.75 2.531,0.948 0.458,0.198 10 false 2 2.073,1.406 2.531,1.604 0.458,0.198 10 false 1 5.479,0.75 5.938,0.948 0.458,0.198 10 false 1 5.5,1.438 5.958,1.635 0.458,0.198 10 false 2 0.708,2.26 4.208,2.49 3.5,0.229 10 false (Turbocharger nozzle vane control actuator)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P004512, P004514 AND/OR P004600)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P004600 is output A
DTC P004518 and/or P004519 is output B
DTC P004518, P004519 and/or P004600 and other DTCs are output C


HINT:

If codes other than DTC P004518, P004519 and/or P004600 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT TURBOCHARGER NOZZLE VANE PLATE

B

5.INSPECT VARIABLE VANE DC MOTOR (RESISTANCE)

C

2.INSPECT TURBOCHARGER NOZZLE VANE PLATE

b.

Inspect the turbocharger nozzle vane plate.

i.

Remove the e-washer from the turbocharger nozzle vane control actuator.



c.
A348999

Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane plate moves.


Result:
Result Proceed to
Catches, but operates* OK
Gets stuck and does not operate NG


HINT:

*: Check several times.



OK

3.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR

NG

4.REPLACE TURBOCHARGER SUB-ASSEMBLY
3.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
a.

Replace the turbocharger nozzle vane control actuator.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.INSPECT VARIABLE VANE DC MOTOR (RESISTANCE)
a.
C217215C05
0.12,0.111 0.297,0.288 0.177,0.177 10 *a
*a Component without harness connected
(Variable Vane DC Motor)


Disconnect the variable vane DC motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 1 to 100 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (VARIABLE VANE DC MOTOR - ECM)

NG

10.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
6.CHECK HARNESS AND CONNECTOR (VARIABLE VANE DC MOTOR - ECM)
a.

Disconnect the variable vane DC motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C175-1 (M-) - C151-2 (VNM-) Always Below 1 Ω
C175-2 (M+) - C151-1 (VNM+) Always Below 1 Ω
C175-1 (M-) or C151-2 (VNM-) - Body ground and other terminals Always 10 kΩ or higher
C175-2 (M+) or C151-1 (VNM+) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off and wait for 30 seconds or more.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VN Turbo Open Bank 1.


g.

Maintain the Active Test "Activate the VN Turbo Open Bank 1" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
a.

Replace the turbocharger nozzle vane control actuator.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED