Turn the ignition switch to ON.
w/ Combination Switch:
Press the differential lock switch (combination switch assembly).
w/o Combination Switch:
Press the differential lock switch.
Check the rear differential lock indicator light.
| Result | Proceed to |
|---|---|
| Rear differential lock indicator light blinks or illuminates | A |
| Rear differential lock indicator light remains off regardless of switch operation | B |
| Rear differential lock indicator light remains illuminated regardless of switch operation | C |
Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
A
B
C
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.
(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM)
"Bus Check" indicates no malfunctions in CAN communication.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Four Wheel Drive / Data List.
According to the display on the GTS, read the Data List
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Rear Differential Lock Control SW | Differential lock switch status/
ON or OFF |
ON: ON (LOCK)
OFF: OFF (FREE) |
- |
w/ Combination Switch:
OK: Display changes according to differential lock switch (combination switch assembly) operation
w/o Combination Switch:
OK: Display changes according to differential lock switch operation
OK
NG
Turn the ignition switch off.
Perform an Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
Check the combination meter assembly.
The rear differential lock indicator light turns on or off in accordance with the GTS.
OK
NG
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
w/ Combination Switch:
Remove the differential lock switch (combination switch assembly) (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK CONTROL SWITCH(w/ Combination Switch)>REMOVAL).
w/o Combination Switch:
Remove the differential lock switch (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK CONTROL SWITCH(w/o Combination Switch)>REMOVAL).
w/ Combination Switch:
Inspect the differential lock switch (combination switch assembly) (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH>INSPECTION).
w/o Combination Switch:
Inspect the differential lock switch (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK CONTROL SWITCH(w/o Combination Switch)>INSPECTION).
w/ Combination Switch:
The differential lock switch (combination switch assembly) operates normally.
w/o Combination Switch:
The differential lock switch operates normally.
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | w/ Combination Switch | B |
| w/o Combination Switch | C | |
A
B
C
Disconnect the G53 4 wheel drive control ECU connector.
w/ Combination Switch:
Disconnect the G307 differential lock switch (combination switch assembly) connector.
w/o Combination Switch:
Disconnect the G233 differential lock switch (combination switch assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G53-15 (R) - G307-5 (B) | Always | Below 1 Ω |
| G307-2 (E) - Body ground | Always | Below 1 Ω |
| G53-15 (R) or G307-5 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G53-15 (R) - G233-5 (B) | Always | Below 1 Ω |
| G233-2 (E) - Body ground | Always | Below 1 Ω |
| G53-15 (R) or G233-5 (B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.
(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM)
"Bus Check" indicates no malfunctions in CAN communication.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Four Wheel Drive / Data List
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Rear Differential Lock Indicator Request | Rear differential lock indicator light request/
Blink3, Blink2, Blink1, ON or OFF |
·
Blink3: Indicator light rapidly blinks ·
Blink2: Indicator light blinks 3 times ·
Blink1: Indicator light blinks ·
ON: Indicator light illuminates ·
OFF: Indicator light turns off |
·
Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off) ·
Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off) |
w/ Combination Switch:
Turn the differential lock switch (combination switch assembly) on and off several times and check the GTS display condition of the rear differential lock indicator light.
w/o Combination Switch:
Turn the differential lock switch on and off several times and check the GTS display condition of the rear differential lock indicator light.
| Result | Proceed to |
|---|---|
| Data List continues to display ON even when differential lock switch (combination switch assembly) is operated*1
Data List continues to display ON even when differential lock switch is operated*2 |
A |
| Data List display changes according to differential lock switch (combination switch assembly) operation*1
Data List display changes according to differential lock switch operation*2 |
B |
*1: w/ Combination Switch
*2: w/o Combination Switch
A
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)