2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0010 Camshaft Position "A" Actuator Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The VVT (Variable Valve Timing) system adjusts the intake valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The camshaft Oil Control Valve (OCV) is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
A192077E06
DTC Code
DTC Detection Condition
Trouble Area
P0010
An open or short in the camshaft Oil Control Valve (OCV) (for Bank 1) circuit (1 trip detection logic).
  1. Open or short in camshaft Oil Control Valve (OCV) (for Bank 1) circuit
  2. OCV (for Bank 1)
  3. ECM
P0020
An open or short in the OCV (for Bank 2) circuit (1 trip detection logic).
  1. Open or short in OCV (for Bank 2) circuit
  2. OCV (for Bank 2)
  3. ECM

MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft Oil Control Valve (OCV) circuit. If the OCV duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

A160561E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK DTC
  1. Clear the DTC after recording the freeze frame data and DTC.

  1. Turn the ignition switch off.

  1. Allow the engine to idle and check for DTC.

  1. Check that P0010 or P0020 is output.

    OK:
    P0010 or P0020 is output.



NG
CHECK FOR INTERMITTENT PROBLEMS (Click here)
OK


2. INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY

  1. A160397E02
    Disconnect the camshaft Oil Control Valve (OCV) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω



NG
REPLACE CAMSHAFT OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CAMSHAFT OIL CONTROL VALVE [OCV] - ECM)

  1. A182107E02
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C27-1 - C45-58 (OC1+)
    Always
    Below 1 Ω
    C28-1 - C45-52 (OC2+)
    Always
    Below 1 Ω
    C27-2 - C45-57 (OC1-)
    Always
    Below 1 Ω
    C28-2 - C45-51 (OC2-)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C27-1 - C46-58 (OC1+)
    Always
    Below 1 Ω
    C28-1 - C46-52 (OC2+)
    Always
    Below 1 Ω
    C27-2 - C46-57 (OC1-)
    Always
    Below 1 Ω
    C28-2 - C46-51 (OC2-)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C27-1 or C45-58 (OC1+) - Body ground
    Always
    10 kΩ or higher
    C28-1 or C45-52 (OC2+) - Body ground
    Always
    10 kΩ or higher
    C27-2 or C45-57 (OC1-) - Body ground
    Always
    10 kΩ or higher
    C28-2 or C45-51 (OC2-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C27-1 or C46-58 (OC1+) - Body ground
    Always
    10 kΩ or higher
    C28-1 or C46-52 (OC2+) - Body ground
    Always
    10 kΩ or higher
    C27-2 or C46-57 (OC1-) - Body ground
    Always
    10 kΩ or higher
    C28-2 or C46-51 (OC2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Jan 2012)P0010 Camshaft Position "A" Actuator Circuit (Bank 1) (+ P0020) (from Jan 2012) →