2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0010 Camshaft Position "A" Actuator Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

  1. This DTC is designed to detect opens or shorts in the cam timing oil control valve (OCV) circuit. If the duty-cycle of the OCV is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
  2. The VVT (variable valve timing) system adjusts the intake valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
A130637E18
DTC Code
DTC Detection Condition
Trouble Area
P0010
An open or short in the Cam Timing Oil Control Valve (OCV) (for intake side of bank 1) circuit (1 trip detection logic).
  1. Open or short in Cam Timing Oil Control Valve (OCV) (for intake side of bank 1) circuit
  2. OCV (for intake side of bank 1)
  3. ECM
P0020
An open or short in the Cam Timing Oil Control Valve (OCV) (for intake side of bank 2) circuit (1 trip detection logic).
  1. Open or short in OCV (for intake side of bank 2) circuit
  2. OCV (for intake side of bank 2)
  3. ECM

HINT:
This DTC relates to the Oil Control Valve (OCV).


MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the cam Timing oil control valve (OCV) circuit. If the duty-cycle of the OCV is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

A162759E05

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK DTC
  1. Clear DTC after recording the freeze frame data and DTC (Click here).

  1. Turn the engine switch off.

  1. Allow the engine to idle and check for DTC.

  1. Check that P0010 or P0020 is not output.

    OK:
    P0010 or P0020 is not output.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT CAM TIMING OIL CONTROL VALVE ASSEMBLY

  1. A160397E02
    Disconnect the OCV connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω



NG
REPLACE CAM TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CAM TIMING OIL CONTROL VALVE - ECM)

  1. A182107E01
    Disconnect the OCV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C27-1 - C45-58 (OC1+)
    Always
    Below 1 Ω
    C28-1 - C45-52 (OC2+)
    Always
    Below 1 Ω
    C27-2 - C45-57 (OC1-)
    Always
    Below 1 Ω
    C28-2 - C45-51 (OC2-)
    Always
    Below 1 Ω
    C27-1 or C45-58 (OC1+) - Body ground
    Always
    10 kΩ or higher
    C28-1 or C45-52 (OC2+) - Body ground
    Always
    10 kΩ or higher
    C27-2 or C45-57 (OC1-) - Body ground
    Always
    10 kΩ or higher
    C28-2 or C45-51 (OC2-) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C27-1 - C46-58 (OC1+)
    Always
    Below 1 Ω
    C28-1 - C46-52 (OC2+)
    Always
    Below 1 Ω
    C27-2 - C46-57 (OC1-)
    Always
    Below 1 Ω
    C28-2 - C46-51 (OC2-)
    Always
    Below 1 Ω
    C27-1 or C46-58 (OC1+) - Body ground
    Always
    10 kΩ or higher
    C28-1 or C46-52 (OC2+) - Body ground
    Always
    10 kΩ or higher
    C27-2 or C46-57 (OC1-) - Body ground
    Always
    10 kΩ or higher
    C28-2 or C46-51 (OC2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (Sep 2011 – Dec 2011)P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012, P0021, P0022) (Sep 2011 – Dec 2011) →