2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The VVT system includes the ECM, Cam Timing Oil Control Valve (OCV) and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.
A130637E18
DTC Code
DTC Detection Condition
Trouble Area
P0011
P0021
The valve timing is not adjusted in the valve timing advance range (1 trip detection logic).
  1. Valve timing
  2. Cam Timing Oil Control Valve (OCV) for intake side
  3. OCV filter
  4. Intake camshaft timing tube (for Bank 1, 2)
  5. ECM
P0012
P0022
The valve timing is not adjusted in the valve timing retard range (2 trip detection logic).
  1. Valve timing
  2. OCV for intake side
  3. OCV filter
  4. Intake camshaft timing tube (for Bank 1, 2)
  5. ECM

MONITOR DESCRIPTION

  1. The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the Cam Timing Oil Control Valve (OCV) and the VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
  2. If the difference between the target and actual intake valve timings is large, and changes in the actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and stores a DTC.
  1. Example:
  2. A DTC is stored when the following conditions 1, 2 and 3 are met:
    1. 1. The difference between the target and actual intake valve timing is more than 5°CA (Crankshaft Angle) and the condition continues for more than 4.5 seconds.
    2. 2. It takes 5 seconds or more to change the valve timing by 5°CA.
    3. 3. After above conditions 1 and 2 are met, the OCV is forcibly activated 63 times or more.
  3. DTC P0011 and P0021 (Advanced Cam Timing) are subject to 1 trip detection logic.
  4. DTC P0012 and P0022 (Retarded Cam Timing) are subject to 2 trip detection logic.
  5. These DTCs indicate that the VVT controller cannot operate properly due to OCV malfunctions or the presence of foreign objects in the OCV.
  6. The monitor will run if all of the following conditions are met:
    1. The engine is warm (the engine coolant temperature is 75°C [167°F] or higher).
    2. The vehicle has been driven at more than 64 km/h (40 mph) for 3 minutes.
    3. The engine has idled for 3 minutes.

WIRING DIAGRAM

Refer to DTC P0010 (Click here).

INSPECTION PROCEDURE

HINT:
DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.


HINT:
Abnormal Bank
Advanced Timing Over
(Valve Timing is Out of Specified Range)
Retarded Timing Over
(Valve Timing is Out of Specified Range)
Bank 1
P0011
P0012
Bank 2
P0021
P0022
  1. If DTC P0011 or P0012 is output, check the left bank VVT system for intake side circuit (for bank 1).
  2. Bank 1 refers to the bank that includes the No. 1 cylinder.
  3. If DTC P0021 or P0022 is output, check the right bank VVT system for intake side circuit (for bank 2).
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0011, P0012, P0021 or P0022 is output
    A
    P0011, P0012, P0021 or P0022 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Check the engine speed while operating the Camshaft Oil Control Valve (OCV) using the tester.

    OK 
    Tester Operation
    Specified Condition
    OCV OFF
    Normal engine speed
    OCV ON
    Engine idles roughly or stalls
    (soon after OCV switched from OFF to ON)



NG
Go to step 4
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs using the tester.

    OK:
    No DTC output.



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TOOTH OF TIMING BELT)
A178910E01
  1. Remove the drive belt (Click here).

  1. Remove the timing belt cover LH and RH (Click here).

  1. Turn the crankshaft to align the matchmarks of the crankshaft.

  1. Align the notch of the crankshaft pulley with the "0" position.

  1. Confirm whether the matchmarks of the camshaft pulley and cylinder head cover are facing each other.

  1. If the matchmarks are not facing each other, turn the crankshaft clockwise by 360°. Confirm again if the matchmarks are facing each other.

    OK:
    The matchmarks of the camshaft pulley and the cylinder head cover face each other when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING (Click here)
OK


5. INSPECT CAM TIMING OIL CONTROL VALVE ASSEMBLY (OCV)
A160397E02
A182939E01
  1. Remove the OCV.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

  1. Apply positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.



NG
REPLACE CAM TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6. INSPECT OIL CONTROL VALVE FILTER
A086178E01
  1. Remove the cylinder head cover (Click here).

  1. Remove the camshaft bearing cap and OCV filter.

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
CLEAN OIL CONTROL VALVE FILTER
OK


7. REPLACE CAMSHAFT TIMING TUBE ASSEMBLY
  1. Replace the camshaft timing tube assembly.

    HINT:
    1. If P0011 or P0012 is output, replace the camshaft timing tube assembly for bank 1 (Click here).
    2. If P0021 or P0022 is output, replace the camshaft timing tube assembly for bank 2 (Click here).


NEXT


8. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Drive the vehicle for more than 10 minutes.

  1. Read output DTCs using the tester.

    OK:
    No DTC is output.

    HINT:
    DTC P0011, P0012, P0021 or P0022 is output when foreign objects in the engine oil are caught in some parts of the system. These codes will stay stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

SYSTEM OK


← P0010 Camshaft Position "A" Actuator Circuit (Bank 1) (+ P0020) (Sep 2011 – Dec 2011)P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) (+ P0018) (Sep 2011 – Dec 2011) →