2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0010 Camshaft Position "A" Actuator Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

DESCRIPTION

  1. These DTCs are designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
  2. The VVT (variable valve timing) system adjusts the intake and exhaust valve timing to improve driveability. The engine oil pressure turns the camshaft timing gear to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time of the solenoid (duty cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
A192077E17
DTC No.
DTC Detection Condition
Trouble Area
P0010
Open or short in the camshaft timing oil control valve for intake camshaft (for Bank 1) circuit (1 trip detection logic).
  1. Open or short in camshaft timing oil control valve for intake camshaft (for Bank 1) circuit
  2. Camshaft timing oil control valve assembly for intake camshaft (for Bank 1)
  3. ECM
P0020
Open or short in the camshaft timing oil control valve for intake camshaft (for Bank 2) circuit (1 trip detection logic).
  1. Open or short in camshaft timing oil control valve for intake camshaft (for Bank 2) circuit
  2. Camshaft timing oil control valve assembly for intake camshaft (for Bank 2)
  3. ECM

HINT:
These DTCs relate to the camshaft timing oil control valve.


MONITOR DESCRIPTION

These DTCs are designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
The monitor for this DTC runs 5 seconds after the engine switch is turned on (IG).

CONFIRMATION DRIVING PATTERN

  1. Turn the engine switch on (IG) and wait for 5 seconds or more.

WIRING DIAGRAM

A178641E08

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.


1. CHECK FOR DTC
  1. Clear the DTCs after recording the freeze frame data and DTCs (Click here).

  1. Turn the engine switch off.

  1. Start the engine and allow it to idle. Then check for DTCs.

  1. Check that P0010 or P0020 is not output.

    OK:
    P0010 or P0020 is not output.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect the camshaft timing oil control valve assembly (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)
  1. Disconnect the camshaft timing oil control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C102-1 - C46-58 (OC1+)
    Always
    Below 1 Ω
    C103-1 - C46-52 (OC2+)
    Always
    Below 1 Ω
    C102-2 - C46-57 (OC1-)
    Always
    Below 1 Ω
    C103-2 - C46-51 (OC2-)
    Always
    Below 1 Ω
    C102-1 or C46-58 (OC1+) - Body ground
    Always
    10 kΩ or higher
    C103-1 or C46-52 (OC2+) - Body ground
    Always
    10 kΩ or higher
    C102-2 or C46-57 (OC1-) - Body ground
    Always
    10 kΩ or higher
    C103-2 or C46-51 (OC2-) - Body ground
    Always
    10 kΩ or higher
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C102-1 - C45-58 (OC1+)
    Always
    Below 1 Ω
    C103-1 - C45-52 (OC2+)
    Always
    Below 1 Ω
    C102-2 - C45-57 (OC1-)
    Always
    Below 1 Ω
    C103-2 - C45-51 (OC2-)
    Always
    Below 1 Ω
    C102-1 or C45-58 (OC1+) - Body ground
    Always
    10 kΩ or higher
    C103-1 or C45-52 (OC2+) - Body ground
    Always
    10 kΩ or higher
    C102-2 or C45-57 (OC1-) - Body ground
    Always
    10 kΩ or higher
    C103-2 or C45-51 (OC2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Jan 2012)P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012, P0021, P0022) (from Jan 2012) →