2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ON-VEHICLE INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


PERFORM SPARK TEST
  1. Check for DTCs (Click here).

    NOTICE:
    If any DTC is output, perform troubleshooting procedures for that DTC.

  1. Check if sparks occur.

    1. Remove the 6 spark plugs (Click here).

    2. Install the spark plug to the ignition coil and connect the ignition coil connector.

    3. Remove the engine room relay block cover.

    4. A176383E02
      Remove the circuit opening relay (C/OPN).

    5. Ground the spark plug.

    6. Visually check that sparks occur while the engine is being cranked.

      NOTICE:
      1. Be sure to ground the spark plug when checking.
      2. Replace the ignition coil if it receives an impact.
      3. Do not crank the engine for more than 2 seconds.

  1. Check that the wire harness side connector of the ignition coil with igniter is securely connected.

    Result 
    Result
    Proceed to
    NG
    Connect securely
    OK
    Go to next step

  1. Perform a spark test on each ignition coil with igniter.

    1. If there is a cylinder where sparks do not occur, replace its ignition coil with the ignition coil of a cylinder where sparks occur normally.

    2. Crank the engine and visually check that sparks occur at the cylinder with the normally operating ignition coil.

      Result 
      Result
      Proceed to
      OK
      Replace ignition coil with igniter
      NG
      Go to next step

  1. Inspect the spark plug.

    1. Replace the spark plug with a normal one.

    2. Perform spark test again.

      Result 
      Result
      Proceed to
      OK
      Replace spark plug
      NG
      Go to next step

  1. Check power supply to ignition coil with igniter.

    1. Turn the ignition switch on (IG).

    2. Check that there is battery voltage at ignition coil positive (+) terminal.

      Result 
      Result
      Proceed to
      NG
      Check wiring between ignition switch and ignition coil with igniter
      OK
      Go to next step

  1. Check the VVT sensor (Click here).

  1. Check the crankshaft position sensor (Click here).

  1. Install the 6 spark plugs (Click here).

  1. Install the circuit opening relay.

  1. Install the engine room relay block cover.


INSPECT SPARK PLUG

  1. I039522E10
    Check the electrode.

    1. Using a megohmmeter, measure the insulation resistance.

      Standard Insulation Resistance:
      Tester Connection
      Condition
      Specified Condition
      Spark Plug (terminal part) - Body Ground
      Always
      10 MΩ or higher

      If a megohmmeter is not available, perform the following simple inspection.

  1. G037847E01
    Alternative inspection method:

    1. Quickly accelerate the engine to 4000 rpm 5 times.

    2. Remove the spark plug.

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage on its threads and insulator.
    If there is damage, replace the spark plug. If not, reinstall the spark plug.

    Recommended Spark Plug:
    Manufacturer
    Product
    DENSO made
    K20HR-U11
    NGK made
    LFR6C11

  1. B062019E01
    Clean the spark plugs.

  1. G037848E04
    Check the spark plug electrode gap.

    Maximum electrode gap for used spark plug:
    1.3 mm (0.0512 in.)

    If the gap is more than the maximum, replace the spark plug.

    Electrode gap for new spark plug:
    1.0 to 1.1 mm (0.0394 to 0.0433 in.)

← SYSTEM DIAGRAM (from Jan 2012)ON-VEHICLE INSPECTION (from Jan 2012) →