2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0340 Camshaft Position Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The Variable Valve Timing (VVT) sensor (VV1, 2 signal) of the intake camshaft consists of a magnet and MRE (Magnetic Resistance Element).
The VVT camshaft drive gear has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
The crankshaft angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.
DTC Code
DTC Detection Condition
Trouble Area
P0340
P0345
When either condition below is met:
  1. The input voltage to the ECM remains below 0.3 V or higher than 4.7 V for 4 seconds when 2 or more seconds have elapsed after turning the ignition switch ON (1 trip detection logic).
  2. No VVT sensor signal is sent to the ECM during cranking (2 trip detection logic).
  1. Open or short in VVT sensor circuit
  2. VVT sensor
  3. Camshaft timing gear assembly
  4. Jumped tooth of timing chain
  5. ECM
P0342
P0347
The output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
P0343
P0348
The output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).

  1. A107148E11
    Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveform is as shown.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.

    Item
    Content
    Terminal
    NE+ - NE-
    VV1+ - VV1-
    VV2+ - VV2-
    Equipment Setting
    5 V/DIV.
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

A160377E03

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK VVT SENSOR (SENSOR POWER SOURCE)

  1. A107149E91
    Disconnect the VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C25-3 (VC) - Body ground
    Always
    4.5 to 5.0 V
    C26-3 (VC) - Body ground
    Always
    4.5 to 5.0 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

  1. A182257E01
    Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C26-1 (VVR+) - C45-69 (VV1+)
    Always
    Below 1 Ω
    C26-2 (VVR-) - C45-92 (VV1-)
    Always
    Below 1 Ω
    C25-1 (VVL+) - C45-67 (VV2+)
    Always
    Below 1 Ω
    C25-2 (VVL-) - C45-90 (VV2-)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C26-1 (VVR+) - C46-69 (VV1+)
    Always
    Below 1 Ω
    C26-2 (VVR-) - C46-92 (VV1-)
    Always
    Below 1 Ω
    C25-1 (VVL+) - C46-67 (VV2+)
    Always
    Below 1 Ω
    C25-2 (VVL-) - C46-90 (VV2-)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C26-1 (VVR+) or C45-69 (VV1+) - Body ground
    Always
    10 kΩ or higher
    C26-2 (VVR-) or C45-92 (VV1-) - Body ground
    Always
    10 kΩ or higher
    C25-1 (VVL+) or C45-67 (VV2+) - Body ground
    Always
    10 kΩ or higher
    C25-2 (VVL-) or C45-90 (VV2-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C26-1 (VVR+) or C46-69 (VV1+) - Body ground
    Always
    10 kΩ or higher
    C26-2 (VVR-) or C46-92 (VV1-) - Body ground
    Always
    10 kΩ or higher
    C25-1 (VVL+) or C46-67 (VV2+) - Body ground
    Always
    10 kΩ or higher
    C25-2 (VVL-) or C46-90 (VV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK SENSOR INSTALLATION

  1. BR03795E17
    Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4. CHECK VALVE TIMING

  1. G036290E13
    Remove the cylinder head cover (for bank 1, Click here, or for bank 2, Click here).

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


5. CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
  1. Check the teeth of the signal plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


6. REPLACE VVT SENSOR
  1. Replace the VVT sensor (Click here).


NEXT


7. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No output
    A
    P0340, P0342, P0343, P0345, P0347 or P0348
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (from Jan 2012)P0340 Camshaft Position Sensor Circuit Malfunction (+ 5 more codes) (from Jan 2012) →