P0335 Crankshaft Position Sensor "A" Circuit
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- P0339 Crankshaft Position Sensor "A" Circuit Intermittent
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil.The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0335 |
When either condition below is met:
|
|
| P0339 |
Under conditions (a), (b) and (c), no CKP sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic): (a) The engine speed is 1000 rpm or more. (b) The starter signal is off. (c) 3 seconds or more have elapsed since the starter signal switched from on to off. |
|
-
Reference: Inspection using an oscilloscope.

- HINT:
- The correct waveform is as shown.
- VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.
- Grounding failure of the shielded wire may cause noise in the waveforms.
- The correct waveform is as shown.
Item
Content
Terminal
VV1+ - VV1-
VV2+ - VV2-
NE+ - NE-
Equipment Setting
5 V/DIV.,
20 msec./DIV.
Condition
Cranking or idling
MONITOR DESCRIPTION
If there is no signal from the CKP sensor despite the engine running, the ECM interprets this as a malfunction of the sensor.If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Check the engine speed. The engine speed can be checked by using the intelligent tester. To check, follow the operation below:
- Connect the intelligent tester to the DLC3.
- Start the engine.
- Turn the tester on.
- Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
- The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the Crankshaft Position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the CKP sensor output voltage is insufficient.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- Check the engine speed. The engine speed can be checked by using the intelligent tester. To check, follow the operation below:
| 1. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
Start the engine.
Read the values displayed on the tester while the engine is running.
- OK:
- Correct values are displayed.
- HINT:
- To check the engine speed change, display the graph on the tester.
- If the engine does not start, check the engine speed while cranking.
- If the engine speed indicated on the tester remains at zero (0), there may be an open or short in the Crankshaft Position (CKP) sensor circuit.
- To check the engine speed change, display the graph on the tester.
|
|
||||
| OK | ||
| ||
| 2. INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE) |
![]() ![]() |
Disconnect the Crankshaft Position (CKP) sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Cold
1630 to 2740 Ω
1 - 2
Hot
2065 to 3225 Ω
- HINT:
- The terms "Cold" and "Hot" refer to the temperature of the sensor. Cold means approximately -10 to 50°C (14 to 122°F). Hot means approximately 50 to 100°C (122 to 212°F).
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
![]() ![]() |
Disconnect the CKP sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
for LHD Tester Connection
Condition
Specified Condition
C1-1 - C45-110 (NE+)
Always
Below 1 Ω
C1-2 - C45-111 (NE-)
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
C1-1 - C46-110 (NE+)
Always
Below 1 Ω
C1-2 - C46-111 (NE-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
for LHD Tester Connection
Condition
Specified Condition
C1-1 or C45-110 (NE+) - Body ground
Always
10 kΩ or higher
C1-2 or C45-111 (NE-) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
C1-1 or C46-110 (NE+) - Body ground
Always
10 kΩ or higher
C1-2 or C46-111 (NE-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
![]() ![]() |
Check the CKP sensor installation.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 5. CHECK CRANK ANGLE SENSOR PLATE (TEETH OF SENSOR PLATE) |
Check the teeth of the sensor plate.
- OK:
- Sensor plate does not have any cracks or deformation.
|
|
||||
| OK | |
| 6. REPLACE CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
| NEXT | |
| 7. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
No output
A
P0335 or P0339
B
- HINT:
- If the engine does not start, replace the ECM.
|
|
||||
| A | ||
| ||



