2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

Flat type knock sensors (non-resonant type) have structures that can detect vibrations between approximately 6 kHz and 15 kHz.
A knock sensor is fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
DTC Code
DTC Detection Condition
Trouble Area
P0327
P0332
The output voltage of the knock sensor is below 0.5 V (1 trip detection logic).
  1. Short in knock sensor circuit
  2. Knock sensor
  3. ECM
P0328
P0333
The output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic).
  1. Open in knock sensor circuit
  2. Knock sensor
  3. ECM

HINT:
When any of DTCs P0327, P0328, P0332 and P0333 are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.

Reference: Inspection using an oscilloscope
A185975E01
The correct waveform is as shown.
Item
Content
Terminal
KNK1 - EKNK
KNK2 - EKN2
Equipment Setting
1 V/DIV.
1 msec./DIV.
Condition
Engine speed maintained at 4000 rpm with warm engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.
The monitor for DTCs P0327, P0328, P0332 and P0333 begins to run when 5 seconds have elapsed since the engine was started.
If the malfunction is not repaired successfully, DTC P0327, P0328, P0332 or P0333 is stored 5 seconds after the engine is next started.

WIRING DIAGRAM

A160376E02

INSPECTION PROCEDURE

HINT:
  1. DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.
  2. DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.
  3. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ DTC OUTPUT (CHECK KNOCK SENSOR CIRCUIT)
A182259E01
  1. Disconnect the CU1 connector.

  1. Using lead wires, connect the connectors as follows:

Male Connector - Female Connector
Terminal 2 - Terminal 4
Terminal 5 - Terminal 6
Terminal 4 - Terminal 2
Terminal 6 - Terminal 5
  1. Warm up the engine.

  1. Run the engine at 3000 rpm for 10 seconds or more.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is same as when vehicle brought in
    (for example, P0327 and P0328 are output again, or P0332 and P0333 are output again)
    A
    DTC is different from when vehicle brought in
    (for example, P0327 and P0328 are output at first, but then P0332 and P0333 are output, or vice versa)
    B



B
Go to step 4
A


2. CHECK HARNESS AND CONNECTOR (CONNECTOR - ECM)
A182255E01
  1. Disconnect the CU1 connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    CU1 female connector 2 - C45-95 (KNK1)
    Always
    Below 1 Ω
    CU1 female connector 5 - C45-94 (EKNK)
    Always
    Below 1 Ω
    CU1 female connector 4 - C45-118 (KNK2)
    Always
    Below 1 Ω
    CU1 female connector 6 - C45-117 (EKN2)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    CU1 female connector 2 - C46-95 (KNK1)
    Always
    Below 1 Ω
    CU1 female connector 5 - C46-94 (EKNK)
    Always
    Below 1 Ω
    CU1 female connector 4 - C46-118 (KNK2)
    Always
    Below 1 Ω
    CU1 female connector 6 - C46-117 (EKN2)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    CU1 female connector 2 or C45-95 (KNK1) - Body ground
    Always
    10 kΩ or higher
    CU1 female connector 5 or C45-94 (EKNK) - Body ground
    Always
    10 kΩ or higher
    CU1 female connector 4 or C45-118 (KNK2) - Body ground
    Always
    10 kΩ or higher
    CU1 female connector 6 or C45-117 (EKN2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    CU1 female connector 2 or C46-95 (KNK1) - Body ground
    Always
    10 kΩ or higher
    CU1 female connector 5 or C46-94 (EKNK) - Body ground
    Always
    10 kΩ or higher
    CU1 female connector 4 or C46-118 (KNK2) - Body ground
    Always
    10 kΩ or higher
    CU1 female connector 6 or C46-117 (EKN2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (VOLTAGE)
A108338E14
  1. Disconnect the CU1 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    CU1 female connector 2 - 5
    Ignition switch ON
    4.5 to 5.5 V
    CU1 female connector 4 - 6
    Ignition switch ON
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. INSPECT KNOCK SENSOR
A072922E24
  1. Disconnect the CU1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    CU1 male connector 2 - 5
    20°C (68°F)
    120 to 280 kΩ
    CU1 male connector 4 - 6
    20°C (68°F)
    120 to 280 kΩ



NG
Go to step 5
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

5. CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR)
A140663E03

HINT:
  1. If DTC P0327 or P0328 has changed to P0332 or P0333, check the knock sensor circuit on the right bank side.
  2. If DTC P0332 or P0333 has changed to P0327 or P0328, check the knock sensor circuit on the left bank side.

  1. Disconnect the CU1 connector.

  1. Disconnect the knock sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    CU1 male connector 2 - U2-2
    Always
    Below 1 Ω
    CU1 male connector 5 - U2-1
    Always
    Below 1 Ω
    CU1 male connector 4 - U1-2
    Always
    Below 1 Ω
    CU1 male connector 6 - U1-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    CU1 male connector 2 or U2-2 - Body ground
    Always
    10 kΩ or higher
    CU1 male connector 5 or U2-1 - Body ground
    Always
    10 kΩ or higher
    CU1 male connector 4 or U1-2 - Body ground
    Always
    10 kΩ or higher
    CU1 male connector 6 or U1-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE KNOCK SENSOR (Click here)


← P0300 Random / Multiple Cylinder Misfire Detected (+ 6 more codes) (from Jan 2012)P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (+ P0328, P0332, P0333) (from Jan 2012) →