2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
DTC Code
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).
  1. (a) The vehicle speed is 20 km/h (12.4 mph) or more.
  2. (b) The engine speed is 1000 rpm or more.
  3. (c) The STA signal is on.
  1. Park/Neutral Position (PNP) switch
  2. ST relay circuit
  3. Ignition switch
  4. ECM

WIRING DIAGRAM

A180644E06
A180644E22
A264511E01
A180644E23
A264511E02

INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
    If the engine will not crank, proceed to the Problem Symptoms Table (Click here).
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to ON and when the engine is started.

    Standard:
    Ignition Switch Condition
    Display (Starter Signal)
    ON
    OFF
    Engine is started
    ON

    Result 
    Result
    Proceed to
    NG (AT)
    A
    NG (MT)
    B
    OK
    C



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch (Click here).

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 7
A


3. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Replace the park/neutral position switch (Click here).



NEXT
Go to step 6
4. INSPECT CLUTCH START SWITCH
  1. Check the clutch start switch (for LHD) (Click here).

  1. Check the clutch start switch (for RHD) (Click here).

Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 7
A


5. REPLACE CLUTCH START SWITCH
  1. Replace the clutch start switch (for LHD) (Click here).

  1. Replace the clutch start switch (for RHD) (Click here).


NEXT


6. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to ON and when the engine is started.

    Standard:
    Ignition Switch Condition
    Display (Starter Signal)
    ON
    OFF
    Engine is started
    ON

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
SYSTEM OK
A


7. CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)

  1. for Automatic transmission.

    1. A179964E08
      Disconnect the PNP switch connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open):
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      C24-5 - A38-48 (STA)
      Always
      Below 1 Ω
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      C24-5 - A52-48 (STA)
      Always
      Below 1 Ω


      Standard Resistance (Check for Short):
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      C24-5 or A38-48 (STA) - Body ground
      Always
      10 kΩ or higher
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      C24-5 or A52-48 (STA) - Body ground
      Always
      10 kΩ or higher

  1. for Manual transmission.

    1. A168714E23
      Disconnect the clutch pedal switch connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open):
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      A49-2 - A38-48 (STA)
      Always
      Below 1 Ω
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      A49-2 - A52-48 (STA)
      Always
      Below 1 Ω


      Standard Resistance (Check for Short):
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      A49-2 or A38-48 (STA) - Body ground
      Always
      10 kΩ or higher
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      A49-2 or A52-48 (STA) - Body ground
      Always
      10 kΩ or higher



NG
REPLACE HARNESS OR CONNECTOR
OK


8. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at more than 20 km/h (12.4 mph) for more than 20 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC
    A
    P0617 (w/ Entry and Start System)
    B
    P0617 (w/o Entry and Start System)
    C



B
GO TO CRANKING HOLDING FUNCTION CIRCUIT (Click here)

C
GO TO STARTER SIGNAL CIRCUIT (Click here)
A

SYSTEM OK


← P060E Internal Control Module Throttle Position Performance (from Jan 2012)P0617 Starter Relay Circuit High (from Jan 2012) →