2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The Crank Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil.
The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.
DTC Code
DTC Detection Condition
Trouble Area
P0335
When either condition below is met:
  1. No CKP sensor signal is sent to the ECM while cranking (1 trip detection logic).
  2. No CKP sensor signal is sent to the ECM at an engine speed of 450 rpm or more (1 trip detection logic).
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. CKP sensor plate
  4. ECM
P0339
Under conditions (a), (b) and (c), no CKP sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) An engine speed of 1000 rpm or more.
(b) The starter signal is OFF.
(c) 3 seconds or more have elapsed since the starter signal switched from ON to OFF.
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. CKP sensor plate
  4. ECM

  1. A164292E02
    Reference: Inspection using an oscilloscope.

    HINT:
    1. The correct waveform is as shown.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.
    3. Grounding failure of the shielded wire may cause noise in the waveforms.

    Item
    Content
    Terminal
    VV1+ - VV1-
    VV2+ - VV2-
    NE+ - NE-
    Equipment Setting
    2 V/DIV.,
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION

If there is no signal from the CKP sensor despite the engine running, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

WIRING DIAGRAM

A164727E02

INSPECTION PROCEDURE

HINT:
  1. If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical systems.
  2. Check the engine speed. The engine speed can be checked by using the intelligent tester. To check, follow the operation below:
    1. Connect the intelligent tester to the DLC3.
    2. Start the engine.
    3. Turn the tester on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the Crankshaft Position (CKP) sensor. Alternatively, the engine speed may be indicated as less than the actual engine speed if the CKP sensor output voltage is insufficient.
  3. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ENGINE SPD)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the tester while the engine is running.

    Standard:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the tester.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the tester remains at zero (0), there may be an open or short in the Crank Position (CKP) sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT CRANK POSITION SENSOR (RESISTANCE)
A160397E11
  1. Disconnect the crank position (CKP) sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    1630 to 2740 Ω
    1 - 2
    Hot
    2065 to 3225 Ω

    NOTICE:
    In the above chart, the terms "cold" and "hot" refer to the temperature of the sensor.
    "Cold" means approximately -10 to 50°C (14 to 122°F).
    "Hot" means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE CRANK POSITION SENSOR (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CRANK POSITION SENSOR - ECM)
A182392E01
  1. Disconnect the CKP sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C48-1 (NE+) - C45-110 (NE+)
    Always
    Below 1 Ω
    C48-2 (NE-) - C45-111 (NE-)
    Always
    Below 1 Ω
    C48-1 (NE+) or C45-110 (NE+) - Body ground
    Always
    10 kΩ or higher
    C48-2 (NE-) or C45-111 (NE-) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C48-1 (NE+) - C46-110 (NE+)
    Always
    Below 1 Ω
    C48-2 (NE-) - C46-111 (NE-)
    Always
    Below 1 Ω
    C48-1 (NE+) or C46-110 (NE+) - Body ground
    Always
    10 kΩ or higher
    C48-2 (NE-) or C46-111 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK SENSOR INSTALLATION (CRANK POSITION SENSOR)
BR03795E25
  1. Check the CKP sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


5. CHECK CRANKSHAFT POSITION SENSOR PLATE NO. 1 (TEETH OF SENSOR PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT POSITION SENSOR PLATE NO. 1
OK


6. REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crank position sensor (Click here).


NEXT


7. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0335 or P0339 is output
    B

HINT:
If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (+ P0328, P0332, P0333) (Sep 2011 – Dec 2011)P0340 Camshaft Position Sensor Circuit Malfunction (+ P0345) (Sep 2011 – Dec 2011) →