2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

Flat type knock sensors (non-resonant type) have structures that can detect vibrations between approximately 6 kHz and 15 kHz.
A knock sensor is fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
DTC Code
DTC Detection Condition
Trouble Area
P0327
P0332
The output voltage of the knock sensor is below 0.5 V (1 trip detection logic).
  1. Short in knock sensor circuit
  2. Knock sensor
  3. ECM
P0328
P0333
The output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic).
  1. Open in knock sensor circuit
  2. Knock sensor
  3. ECM

HINT:
When any of DTCs P0327, P0328, P0332 and P0333 are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the engine switch is turned off.

Reference: Inspection using an oscilloscope
A085286E48
The correct waveform is as shown.
Item
Content
Terminal
KNK1 - EKNK
KNK2 - EKN2
Equipment Setting
1 V/DIV.
1 msec./DIV.
Condition
Keep engine speed at 4000 rpm with warm engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.
The monitor for DTCs P0327, P0328, P0332 and P0333 begins to run when 5 seconds have elapsed since the engine was started.
If the malfunction is not repaired successfully, DTC P0327, P0328, P0332 or P0333 is stored 5 seconds after the engine is next started.

WIRING DIAGRAM

A163648E02

INSPECTION PROCEDURE

HINT:
  1. DTCs P0327 and P0328 are the bank 1 knock sensor circuit.
  2. DTCs P0332 and P0333 are the bank 2 knock sensor circuit.
  3. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ DTC OUTPUT (CHECK KNOCK SENSOR CIRCUIT)
A164726E02
  1. Disconnect the DC1 connector.

  1. Using lead wires, connect the connectors as follows:

Male Connector - Female Connector
Terminal 10 - Terminal 4
Terminal 9 - Terminal 5
Terminal 4 - Terminal 10
Terminal 5 - Terminal 9
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Clear DTCs (Click here).

  1. Warm up the engine.

  1. Run the engine at 3000 rpm for 10 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Display
    Proceed to
    DTC is same as when vehicle brought in (for example, P0327 and P0328 are output again, or P0332 and P0333 are output again)
    A
    DTC is different from when vehicle brought in (for example, P0327 and P0328 are output at first, but then P0332 and P0333 are output, or vice versa)
    B

HINT:
  1. If DTC P0327 or P0328 has changed to P0332 or P0333, check the knock sensor circuit on the left bank side.
  2. If DTC P0332 or P0333 has changed to P0327 or P0328, check the knock sensor circuit on the right bank side.



B
Go to step 4
A


2. CHECK HARNESS AND CONNECTOR (CONNECTOR - ECM)
A160394E03
  1. Disconnect the DC1 connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    DC1 male connector 10 - C45-94 (KNK1)
    Always
    Below 1 Ω
    DC1 male connector 9 - C45-93 (EKNK)
    Always
    Below 1 Ω
    DC1 male connector 4 - C45-117 (KNK2)
    Always
    Below 1 Ω
    DC1 male connector 5 - C45-116 (EKN2)
    Always
    Below 1 Ω
    DC1 male connector 10 or C45-94 (KNK1) - Body ground
    Always
    10 kΩ or higher
    DC1 male connector 9 or C45-93 (EKNK) - Body ground
    Always
    10 kΩ or higher
    DC1 male connector 4 or C45-117 (KNK2) - Body ground
    Always
    10 kΩ or higher
    DC1 male connector 5 or C45-116 (EKN2) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    DC1 male connector 10 - C46-94 (KNK1)
    Always
    Below 1 Ω
    DC1 male connector 9 - C46-93 (EKNK)
    Always
    Below 1 Ω
    DC1 male connector 4 - C46-117 (KNK2)
    Always
    Below 1 Ω
    DC1 male connector 5 - C46-116 (EKN2)
    Always
    Below 1 Ω
    DC1 male connector 10 or C46-94 (KNK1) - Body ground
    Always
    10 kΩ or higher
    DC1 male connector 9 or C46-93 (EKNK) - Body ground
    Always
    10 kΩ or higher
    DC1 male connector 4 or C46-117 (KNK2) - Body ground
    Always
    10 kΩ or higher
    DC1 male connector 5 or C46-116 (EKN2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (VOLTAGE)
A160393E02
  1. Disconnect the DC1 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    DC1 male connector 10 - 9
    Engine switch on (IG)
    4.5 to 5.5 V
    DC1 male connector 4 - 5
    Engine switch on (IG)
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. INSPECT KNOCK CONTROL SENSOR
A160903E02
  1. Disconnect the DC1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DC1 female connector 10 - 9
    20°C (68°F)
    120 to 280 kΩ
    DC1 female connector 4 - 5
    20°C (68°F)
    120 to 280 kΩ

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


5. CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR)
A160396E03
  1. Disconnect the DC1 connector.

  1. Disconnect the knock sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DC1 female connector 10 - D7-2
    Always
    Below 1 Ω
    DC1 female connector 9 - D7-1
    Always
    Below 1 Ω
    DC1 female connector 4 - D6-2
    Always
    Below 1 Ω
    DC1 female connector 5 - D6-1
    Always
    Below 1 Ω
    DC1 female connector 10 or D7-2 - Body ground
    Always
    10 kΩ or higher
    DC1 female connector 9 or D7-1 - Body ground
    Always
    10 kΩ or higher
    DC1 female connector 4 or D6-2 - Body ground
    Always
    10 kΩ or higher
    DC1 female connector 5 or D6-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE KNOCK CONTROL SENSOR (Click here)


← P0300 Random / Multiple Cylinder Misfire Detected (+ 8 more codes) (Sep 2011 – Dec 2011)P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (Sep 2011 – Dec 2011) →