2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0340 Camshaft Position Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The Variable Valve Timing (VVT) sensor consists of a magnet, iron core and pickup coil. The VVT signal plate has 3 teeth on its outer circumference and is installed on the camshaft timing pulley. When the camshaft rotates, changes occur on the camshaft protrusions and the pickup coil air gaps. These changes cause fluctuations in the magnetic field and generate voltage in the pickup coil.
Each sensor monitors its timing rotor, which is located on the camshaft. The ECM uses the sensor to detect the camshaft angle. The camshaft rotation synchronizes with the crankshaft rotation, and this sensor communicates the rotation of the camshaft timing rotor as a pulse signal to the ECM. Based on the signal, the ECM controls the camshaft position.
The crankshaft angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.
DTC Code
DTC Detection Condition
Trouble Area
P0340
P0345
When either condition below is met:
  1. No VVT sensor signal is sent to the ECM during cranking (2 trip detection logic).
  2. No VVT sensor signal is sent to the ECM with an engine speed of 600 rpm or more (1 trip detection logic).
  1. Open or short in VVT sensor circuit
  2. VVT sensor
  3. Intake camshaft
  4. Timing belt has a jumped tooth
  5. ECM

  1. A164292E02
    Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveform is as shown.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.

    Item
    Content
    Terminal
    NE+ - NE-
    VV1+ - VV1-
    VV2+ - VV2-
    Equipment Setting
    2 V/DIV.
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine running, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT VVT SENSOR (RESISTANCE)

  1. A160402E03
    Disconnect the VVT sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    835 to 1400 Ω
    1 - 2
    Hot
    1060 to 1645 Ω

    NOTICE:
    In the above chart, the terms "cold" and "hot" refer to the temperature of the coils.
    "Cold" means approximately -10 to 50°C (14 to 122°F).
    "Hot" means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE VVT SENSOR (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

  1. A182393E01
    Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C57-1 - C45-92 (VV1+)
    Always
    Below 1 Ω
    C57-2 - C45-91 (VV1-)
    Always
    Below 1 Ω
    C58-1 - C45-87 (VV2+)
    Always
    Below 1 Ω
    C58-2 - C45-88 (VV2-)
    Always
    Below 1 Ω
    C57-1 or C45-92 (VV1+) - Body ground
    Always
    10 kΩ or higher
    C57-2 or C45-91 (VV1-) - Body ground
    Always
    10 kΩ or higher
    C58-1 or C45-87 (VV2+) - Body ground
    Always
    10 kΩ or higher
    C58-2 or C45-88 (VV2-) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C57-1 - C46-92 (VV1+)
    Always
    Below 1 Ω
    C57-2 - C46-91 (VV1-)
    Always
    Below 1 Ω
    C58-1 - C46-87 (VV2+)
    Always
    Below 1 Ω
    C58-2 - C46-88 (VV2-)
    Always
    Below 1 Ω
    C57-1 or C46-92 (VV1+) - Body ground
    Always
    10 kΩ or higher
    C57-2 or C46-91 (VV1-) - Body ground
    Always
    10 kΩ or higher
    C58-1 or C46-87 (VV2+) - Body ground
    Always
    10 kΩ or higher
    C58-2 or C46-88 (VV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK SENSOR INSTALLATION (VVT SENSOR)

  1. BR03795E17
    Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4. CHECK INTAKE CAMSHAFT (TEETH)
  1. Remove the cylinder head cover (Click here).

  1. Check the teeth of the intake camshaft.

    OK:
    The intake camshaft does not have any cracks or deformation.



NG
REPLACE INTAKE CAMSHAFT (Click here)
OK


5. REPLACE VVT SENSOR
  1. Replace the VVT sensor (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Clear DTCs.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    No DTC is output
    A
    P0340 or P0345 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (Sep 2011 – Dec 2011)P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 7 more codes) (Sep 2011 – Dec 2011) →