2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P1340 Camshaft Position Sensor "A" (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The cam position sensor (G signal) consists of a magnet, iron core and pickup coil.
The camshaft drive gear (LH) has 3 teeth on its inner circumference. When the camshaft gear rotates, the air gap changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field and results in changes in the resistance of the MRE element.
The crankshaft signal plate has 34 teeth and is mounted on the crankshaft. The crank position sensor generates 34 signals at every revolution. The ECM detects the standard crankshaft angle based on the G signal, and the actual crankshaft angle and engine speed by the NE signal.
DTC Code
DTC Detection Condition
Trouble Area
P1340
No cam position sensor signal is sent to the ECM during cranking (2 trip detection logic).
  1. Open or short in cam position sensor circuit
  2. Camshaft position sensor
  3. Camshaft timing pulley LH
  4. ECM
No cam position sensor signal is sent to the ECM with an engine speed of 600 rpm or more.
P1342
The output voltage of the camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic).
P1343
The output voltage of the camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).

MONITOR DESCRIPTION

The cam position sensor (G signal) consists of a magnet and MRE element.
The camshaft drive gear has 3 teeth on its inner circumference. When the camshaft gear rotates, the air gap changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field and results in changes in the resistance of the MRE element. The crankshaft angle sensor plate has 34 teeth and outputs 34 signals at every revolution. The ECM detects the standard crankshaft angle based on the G signal, and the actual crankshaft angle and engine speed by the NE signal.

WIRING DIAGRAM

A162852E03

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT CAM POSITION SENSOR ASSEMBLY (SENSOR POWER SOURCE)
A160975E02
  1. Disconnect the cam position sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C49-3 (VC) - Body ground
    Engine switch on (IG)
    4.5 to 5.0 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (ECM - CAM POSITION SENSOR)
A160974E03
  1. Disconnect the cam position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C49-2 (G2) - C45-90 (G2)
    Always
    Below 1 Ω
    C49-1 (G-) - C45-89 (G2-)
    Always
    Below 1 Ω
    C49-2 (G2) or C45-90 (G2) - Body ground
    Always
    10 kΩ or higher
    C49-1 (G-) or C45-89 (G2-) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C49-2 (G2) - C46-90 (G2)
    Always
    Below 1 Ω
    C49-1 (G-) - C46-89 (G2-)
    Always
    Below 1 Ω
    C49-2 (G2) or C46-90 (G2) - Body ground
    Always
    10 kΩ or higher
    C49-1 (G-) or C46-89 (G2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT SENSOR INSTALLATION
BR03795E62
  1. Check the cam position sensor installation.

    OK:
    The cam position sensor is installed properly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4. INSPECT CAMSHAFT TIMING PULLEY LH (SIGNAL PLATE TOOTH)
  1. Check the teeth of the signal plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING PULLEY LH (Click here)
OK


5. REPLACE CAM POSITION SENSOR ASSEMBLY
  1. Replace the cam position sensor (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P1340, P1342 and/or P1343 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0724 Brake Switch "B" Circuit High (Sep 2011 – Dec 2011)P1440 Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 1 (+ P1443) (Sep 2011 – Dec 2011) →