2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0724 Brake Switch "B" Circuit High

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.
DTC Code
DTC Detection Condition
Trouble Area
P0724
The stop light switch remains on even when the vehicle is driven in a GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic).
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be stored.

WIRING DIAGRAM

A160611E03

INSPECTION PROCEDURE

HINT:
Using the intelligent tester to read the Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the engine switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the engine switch on (IG).
  5. Turn the tester on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List /
  7. Follow the instructions on the tester and read the Data List.
Item
Measurement Item/
Range (Display)
Normal Condition
Diagnostic Note
Stop Light Switch
Stop light switch status/
ON or OFF
  1. Brake pedal depressed: ON
  2. Brake pedal released: OFF
-

1. INSPECT STOP LIGHT SWITCH
C171632E02
  1. Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

  1. A164768E08
    Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for LHD):
    Tester Connection
    Condition
    Specified Condition
    A38-36 (STP) - Body ground
    Brake pedal is depressed
    11 to 14 V
    A38-36 (STP) - Body ground
    Brake pedal is released
    Below 1 V

    Standard Voltage (for RHD):
    Tester Connection
    Condition
    Specified Condition
    A52-36 (STP) - Body ground
    Brake pedal is depressed
    11 to 14 V
    A52-36 (STP) - Body ground
    Brake pedal is released
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) (Sep 2011 – Dec 2011)P1340 Camshaft Position Sensor "A" (Bank 1 Sensor 2) (+ P1342, P1343) (Sep 2011 – Dec 2011) →