2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0102 Mass or Volume Air Flow Circuit Low Input

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve.
The ECM uses this information to determine the fuel injection time and to provide the appropriate air fuel ratio.
Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.

A122492E01
DTC Code
DTC Detection Condition
Trouble Area
P0102
The Mass Air Flow (MAF) meter voltage is below 0.2 V for 3 seconds (1 trip detection logic).
  1. Open or short in Mass Air Flow (MAF) meter circuit
  2. MAF meter
  3. ECM
P0103
The MAF meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. ECM

HINT:
When any of these DTCs are output, check the airflow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.
Mass Airflow Rate (g/sec.)
Malfunction
Approximately 0.0
  1. Open in Mass Air Flow (MAF) meter power source circuit
  2. Open or short in VG circuit
271.0 or more
Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the MAF meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the MAF meter and stores a DTC.
Example:
When the sensor output voltage remains below 0.2 V, or higher than 4.9 V, for more than 3 seconds, the ECM stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

WIRING DIAGRAM

A182250E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (MASS AIRFLOW RATE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

  1. Read the values displayed on the tester.

    Result 
    Mass Airflow Rate (g/sec.)
    Proceed to
    0.0
    A
    271.0 or more
    B
    Between 1.0 and 270.0*
    C

    HINT:
    *: The value must change when the throttle valve is open or closed with the engine running.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
A107942E13
  1. Disconnect the Mass Air Flow (MAF) meter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C2-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 5
OK


3. INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A182251E01
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C2-3 (VG) - C45-72 (VG)
    Always
    Below 1 Ω
    C2-2 (E2G) - C45-73 (E2G)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C2-3 (VG) - C46-72 (VG)
    Always
    Below 1 Ω
    C2-2 (E2G) - C46-73 (E2G)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C2-3 (VG) or C45-72 (VG) - Body ground
    Always
    10 kΩ or higher
    C2-2 (E2G) or C45-73 (E2G) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C2-3 (VG) or C46-72 (VG) - Body ground
    Always
    10 kΩ or higher
    C2-2 (E2G) or C46-73 (E2G) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - EFI NO. 2 FUSE)
A162153E02
  1. Remove the EFI NO. 2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C2-1 (+B) - EFI NO. 2 fuse (2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C2-1 (+B) or EFI NO. 2 fuse (2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)

6. CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
A107942E14
  1. Disconnect the MAF meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C2-2 (E2G) - Body ground
    Always
    Below 1 Ω



NG
Go to step 7
OK

REPLACE MASS AIR FLOW METER (Click here)

7. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A182251E03
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C2-2 (E2G) - C45-73 (E2G)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C2-2 (E2G) - C46-73 (E2G)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C2-2 (E2G) or C45-73 (E2G) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C2-2 (E2G) or C46-73 (E2G) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) (+ 5 more codes) (from Jan 2012)P0102 Mass or Volume Air Flow Circuit Low Input (+ P0103) (from Jan 2012) →