Engine Coolant Temperature Gauge Malfunction
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM using CAN communication lines. The combination meter assembly displays an engine coolant temperature that is calculated based on the data received from the ECM.WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If there is an open or short in the engine coolant temperature sensor circuit, an SFI system DTC is output. If output, perform troubleshooting on the SFI system first.
| 1. CHECK CAN COMMUNICATION SYSTEM |
Check for DTCs (Click here).
Result Result
Proceed to
CAN communication system DTC is not output
A
CAN communication system (for LHD) DTC is output
B
CAN communication system (for RHD) DTC is output
C
|
|
||||
|
|
||||
| A | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COOLANT TEMP) |
Operate the intelligent tester according to the display and select Active Test.
Combination Meter Tester Display
Test Part
Control Range
Diagnostic Note
Water Temperature Meter Operation
Engine coolant temperature receiver gauge
LOW, NORMAL or HIGH
Perform the test with the vehicle stopped and engine idling.
- HINT:
- Confirm that the vehicle is stopped and the engine is idling.
- OK:
- Needle indication is normal.
Result Result
Proceed to
OK
A
NG (w/ Multi-information Display)
B
NG (w/o Multi-information Display)
C
|
|
||||
|
|
||||
| A | |
| 3. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMPERATURE) |
Operate the intelligent tester according to the display and select Data List.
Combination Meter Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Coolant Temperature
Engine coolant temperature/Min.: -40 (-40), Max.: 140 (284)
After warming up: 80 to 105 (176 to 221)
- Unit: °C (°F)
- If the value is -40 (-40): The sensor circuit is open
- If the value is 140 (284): The sensor circuit is shorted.
- OK:
- Coolant temperature displayed on the intelligent tester is between 80°C (176°F) and 95°C (203°F) after warming up.
Result Result
ResultProceed to
OK
A
NG (w/ Multi-information Display)
B
NG (w/o Multi-information Display)
C
- Unit: °C (°F)
|
|
||||
|
|
||||
| A | |
| 4. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT) |
Operate the intelligent tester according to the display and select Data List.
Engine*1, *2, *3 Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Coolant Temp
Engine coolant temperature:
Min.: -40°C, Max.:140°C
80 to 100°C (176 to 212°F):
After warming up
- If the value is -40°C (-40°F), the sensor circuit is open.
- If the value is 140°C (284°F), the sensor circuit is shorted.
Engine*4 Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Coolant Temp
Engine coolant temperature/
Min.: -40°C, Max.:140°C
After warming up engine: 75 to 90°C (167 to 194°F)
- If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
- After a long soak, the coolant temperature, intake air temperature, and ambient air temperature are approximately equal.
- *1: for 1GR-FE
- *2: for 1UR-FE
- *3: for 3UR-FE
- *4: for 1VD-FTV
- OK:
- Engine coolant temperature value displayed on the intelligent tester is almost the same as actual engine coolant temperature.
Result Result
Proceed to
OK
A
NG (for 1GR-FE)
B
NG (for 1UR-FE)
C
NG (for 3UR-FE)
D
NG (for 1VD-FTV)
E
- If the value is -40°C (-40°F), the sensor circuit is open.
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 5. REPLACE COMBINATION METER ASSEMBLY |
w/ Multi-information Display:
Temporarily replace the combination meter with a new one (Click here).
w/o Multi-information Display:
Temporarily replace the combination meter with a new one (Click here).
| NEXT | |
| 6. CHECK COMBINATION METER ASSEMBLY |
w/ Multi-information Display:
Check that the operation of the combination meter returns to normal (Click here).
w/o Multi-information Display:
Check that the operation of the combination meter returns to normal (Click here).
- OK:
- Operation of combination meter returns to normal.
| Result |
Proceed to |
| OK |
A |
| NG (for 1GR-FE) |
B |
| NG (for 1UR-FE) |
C |
| NG (for 3UR-FE) |
D |
| NG (for 1VD-FTV) |
E |
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
