2011-2013 Land Cruiser · Service Manual Vehicle Interior

Engine Coolant Temperature Gauge Malfunction

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM using CAN communication lines. The combination meter assembly displays an engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E140490E10

INSPECTION PROCEDURE

HINT:
If there is an open or short in the engine coolant temperature sensor circuit, an SFI system DTC is output. If output, perform troubleshooting on the SFI system first.


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    CAN communication system DTC is not output
    A
    CAN communication system (for LHD) DTC is output
    B
    CAN communication system (for RHD) DTC is output
    C



B
Go to CAN COMMUNICATION SYSTEM (Click here)

C
Go to CAN COMMUNICATION SYSTEM (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Operate the intelligent tester according to the display and select Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Water Temperature Meter Operation
    Engine coolant temperature receiver gauge
    LOW, NORMAL or HIGH
    Perform the test with the vehicle stopped and engine idling.

    HINT:
    Confirm that the vehicle is stopped and the engine is idling.

    OK:
    Needle indication is normal.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Multi-information Display)
    B
    NG (w/o Multi-information Display)
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


3. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMPERATURE)
  1. Operate the intelligent tester according to the display and select Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temperature
    Engine coolant temperature/Min.: -40 (-40), Max.: 140 (284)
    After warming up: 80 to 105 (176 to 221)
    1. Unit: °C (°F)
    2. If the value is -40 (-40): The sensor circuit is open
    3. If the value is 140 (284): The sensor circuit is shorted.

    OK:
    Coolant temperature displayed on the intelligent tester is between 80°C (176°F) and 95°C (203°F) after warming up.

    Result 
    Result
    Result
    Proceed to
    OK
    A
    NG (w/ Multi-information Display)
    B
    NG (w/o Multi-information Display)
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


4. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT)
  1. Operate the intelligent tester according to the display and select Data List.

    Engine*1, *2, *3 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temp
    Engine coolant temperature:
    Min.: -40°C, Max.:140°C
    80 to 100°C (176 to 212°F):
    After warming up
    1. If the value is -40°C (-40°F), the sensor circuit is open.
    2. If the value is 140°C (284°F), the sensor circuit is shorted.
    Engine*4 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C, Max.:140°C
    After warming up engine: 75 to 90°C (167 to 194°F)
    1. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
    2. After a long soak, the coolant temperature, intake air temperature, and ambient air temperature are approximately equal.
    1. *1: for 1GR-FE
    2. *2: for 2UZ-FE
    3. *3: for 3UR-FE
    4. *4: for 1VD-FTV

    OK:
    Engine coolant temperature value displayed on the intelligent tester is almost the same as actual engine coolant temperature.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 2UZ-FE)
    C
    NG (for 3UR-FE)
    D
    NG (for 1VD-FTV)
    E



B
Go to SFI SYSTEM (Click here)

C
Go to SFI SYSTEM (Click here)

D
Go to SFI SYSTEM (Click here)

E
Go to ECD SYSTEM (Click here)
A


5. REPLACE COMBINATION METER ASSEMBLY
  1. w/ Multi-information Display:

    1. Temporarily replace the combination meter with a new one (Click here).

  1. w/o Multi-information Display:

    1. Temporarily replace the combination meter with a new one (Click here).


NEXT


6. CHECK COMBINATION METER ASSEMBLY
  1. w/ Multi-information Display:

    1. Check that the operation of the combination meter returns to normal (Click here).

  1. w/o Multi-information Display:

    1. Check that the operation of the combination meter returns to normal (Click here).

OK:
Operation of combination meter returns to normal.

Result 
Result
Proceed to
OK
A
NG (for 1GR-FE)
B
NG (for 2UZ-FE)
C
NG (for 3UR-FE)
D
NG (for 1VD-FTV)
E


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPLACE ECM (Click here)
A

END (COMBINATION METER IS DEFECTIVE)


← Fuel Receiver Gauge Malfunction (from Jan 2012)Engine Coolant Temperature Gauge Malfunction (from Jan 2012) →