2011-2013 Land Cruiser · Service Manual Vehicle Interior

Engine Hood Courtesy Switch Circuit

Circuit diagnosis · Vehicles built from Sep 2011

DESCRIPTION

  1. The engine hood courtesy switch is built into the hood lock. This switch turns on when the engine hood is opened and turns off when the engine hood is closed.

WIRING DIAGRAM

B159038E07

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (ENGINE HOOD COURTESY SWITCH)
  1. Using the intelligent tester, read the Data List.

    Entry&Start 
    Tester Display
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Hood Courtesy Switch
    Engine hood courtesy switch /
    ON or OFF
    ON: Engine hood is open
    OFF: Engine hood is closed
    -

    OK:
    ON (engine hood is open) appears on screen.



NG
Go to step 2
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

2. INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
B219990E01
  1. for Hood Courtesy Switch Connector 2 Pin Type (for LHD):

    1. Remove the hood lock (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      Unlock position
      10 kΩ or higher
      1 - 2
      Lock position
      Below 1 Ω

B219989E01
  1. for Hood Courtesy Switch Connector 2 Pin Type (for RHD):

    1. Remove the hood lock (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      Unlock position
      10 kΩ or higher
      1 - 2
      Lock position
      Below 1 Ω

B216369E01
  1. for Hood Courtesy Switch Connector 4 Pin Type:

    1. Remove the hood lock (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 - 4
      Unlock position
      10 kΩ or higher
      2 - 4
      Lock position
      Below 1 Ω



NG
REPLACE HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
OK


3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - HOOD LOCK AND BODY GROUND)
B184352E03
B216370E01
  1. for Hood Courtesy Switch Connector 2 Pin Type:

    1. Disconnect the E30 ECU connector.

    2. Disconnect the A8 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E30-24 (HSW) - A8-2
      Always
      Below 1 Ω
      A8-1 - Body ground
      Always
      Below 1 Ω
      E30-24 (HSW) or A8-2 - Body ground
      Always
      10 kΩ or higher

  1. for Hood Courtesy Switch Connector 4 Pin Type:

    1. Disconnect the E30 ECU connector.

    2. Disconnect the A8 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E30-24 (HSW) - A8-2
      Always
      Below 1 Ω
      A8-4 - Body ground
      Always
      Below 1 Ω
      E30-24 (HSW) or A8-2 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


← B276A Short to GND in Tilt Sensor Signal Circuit (from Sep 2011)Security Horn Circuit (from Sep 2011) →