P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)
- P2197 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)
- P2198 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)
CAUTION / NOTICE / HINT
DESCRIPTION
The A/F sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: The value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted into a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.


| DTC Code |
DTC Detection Condition |
Trouble Area |
| P2195 P2197 |
Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) The A/F sensor voltage is higher than 3.8 V for 5 seconds. (b) The Heated Oxygen (HO2) sensor voltage is 0.21 V or higher. |
|
| While the fuel-cut operation is performed (during vehicle deceleration), the A/F sensor current is 3.6 mA or higher for 3 seconds (2 trip detection logic). |
|
|
| P2196 P2198 |
Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) The A/F sensor voltage is below 2.8 V for 5 seconds. (b) The HO2 sensor voltage is below 0.59 V. |
|
| While the fuel-cut operation is performed (during vehicle deceleration), the A/F sensor current is below 1.4 mA for 3 seconds (2 trip detection logic). |
|
- HINT:
- DTCs P2195 and P2196 indicate malfunctions related to bank 1 A/F sensor circuit.
- DTCs P2197 and P2198 indicate malfunctions related to bank 2 A/F sensor circuit.
- Bank 1 refers to the bank that includes the No. 1 cylinder.
- Bank 2 refers to the bank that includes the No. 2 cylinder.
- When either of these DTCs is output, check the A/F sensor output voltage by entering the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / AFS B1 S1 or AFS B2 S1.
- Short-term fuel trim values can also be read using the intelligent tester.
- The ECM regulates the voltages at the A1A+ and A1A- or A2A+ and A2A- terminals of the ECM to a constant level. Therefore, the A/F sensor output voltage cannot be confirmed without using the intelligent tester.
- If the A/F sensor is malfunctioning, the ECM stores DTC P2195, P2196, P2197 or P2198.
- DTCs P2195 and P2196 indicate malfunctions related to bank 1 A/F sensor circuit.
MONITOR DESCRIPTION
- Sensor voltage detection monitor
Under the air-fuel ratio feedback control, if the A/F sensor output voltage indicates rich or lean for a certain period of time, the ECM determines that there is a malfunction in the A/F sensor. The ECM illuminates the MIL and stores a DTC.
Example:
If the A/F sensor output voltage is below 2.8 V (very rich condition) for 5 seconds, despite the rear HO2 sensor output voltage being below 0.59 V, the ECM stores DTC P2196 or P2198. Alternatively, if the A/F sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the rear HO2 sensor output voltage being 0.21 V or higher, DTC P2195 or P2197 is stored.
- Sensor current detection monitor
A rich air-fuel mixture causes a low A/F sensor current, and a lean air-fuel mixture causes a high A/F sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the A/F sensor current during fuel-cut and detects any abnormal current values.
If the A/F sensor output is 3.6 mA or higher for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the A/F sensor and stores DTC P2195 or P2197 (high-side stuck). If the A/F sensor output is below 1.4 mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 or P2198 (low-side stuck).


WIRING DIAGRAM




CONFIRMATION DRIVING PATTERN
- CAUTION:
- Strictly observe posted speed limits, traffic laws, and road conditions when performing these drive patterns.




- (a) Connect the intelligent tester to the DLC3.
- (b) Turn the engine switch on (IG).
- (c) Turn the tester on.
- (d) Clear DTCs (Click here).
- (e) Start the engine, and warm it up until the ECT reaches 75°C (167°F) or higher.
- (f) Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Idle Fuel Cut.
- (g) Drive the vehicle at between 60 km/h (38 mph) and 120 km/h (75 mph) for at least 10 minutes.
- (h) Change the transmission to 2nd gear.
- (i) Drive the vehicle at the proper vehicle speed to perform fuel-cut operation.
- HINT:
- Fuel-cut is performed when the following conditions are met:
- Accelerator pedal fully released.
- Engine speed is 2500 rpm or more (fuel injection returns at 1000 rpm).
- Accelerator pedal fully released.
- (j) Accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds.
- (k) Soon after performing step (j) above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal, in order to execute fuel-cut control.
- (l) Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).
- (m) Repeat steps (h) through (k) above at least 3 times in one driving cycle.
- HINT:
- Completion of all O2S (A/F) Monitor is required to change the value in the Data List.
INSPECTION PROCEDURE
- HINT:
- Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
- Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
- DTC P2A00 may be stored when the air-fuel ratio is stuck rich or lean.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
- A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
- Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
- HINT:
- Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
- (a) Connect the intelligent tester to the DLC3.
- (b) Start the engine and turn the tester on.
- (c) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
- (d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
- (e) Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
- (f) Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2) displayed on the tester.
- HINT:
- The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- The sensors react in accordance with increases and decreases in the fuel injection volume.
- The sensors react in accordance with increases and decreases in the fuel injection volume.
- Standard:
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1 S1
(A/F)
+25%
Rich
Below 3.0
-12.5%
Lean
Higher than 3.35
O2S B1 S2
(HO2)
+25%
Rich
Higher than 0.55
-12.5%
Lean
Below 0.4
AFS B2 S1
(A/F)
+25%
Rich
Below 3.0
-12.5%
Lean
Higher than 3.35
O2S B2 S2
(HO2)
+25%
Rich
Higher than 0.55
-12.5%
Lean
Below 0.4
- NOTICE:
- The A/F sensor has an output delay of a few seconds and the HO2 sensor (for sensor 2) output has a maximum output delay of approximately 20 seconds.
| Case |
A/F Sensor (Sensor 1) Output Voltage |
HO2 Sensor (Sensor 2) Output Voltage |
Main Suspected Trouble Area |
| 1 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
- |
| 2 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
|
| 3 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
|
| 4 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
|
- Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
- To display the graph, enter the following menus on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/ F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
Result Result
Proceed to
P2195, P2196, P2197 or P2198 is output
A
P2195, P2196, P2197 or P2198 and other DTCs are output
B
- HINT:
- If any DTCs relating to the A/F sensor (DTCs for the A/F sensor heater or A/F sensor admittance) are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Clear DTCs (Click here).
Start the engine.
Allow the vehicle to drive in accordance with the drive pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Data List / Monitor Status.
Check that the status of O2S (A/FS) Monitor is Complete.If the status is still Incomplete, drive the vehicle according to the driving pattern again.
- HINT:
- Complete indicates that the component is functioning normally.
- Incomplete indicates that the component is malfunctioning.
- Complete indicates that the component is functioning normally.
Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / AFS B1 S1 or AFS B2 S1.
Check the test value of the A/F sensor output current during fuel-cut.
Result Test Value
Proceed to
Within normal range (1.4 mA or higher, and below 3.6 mA)
A
Outside normal range (Below 1.4 mA, or 3.6 mA or higher)
B
|
|
||||
| A | |
| 3. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the A/F sensor at an engine speed of 2500 rpm for 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / Snapshot / AFS B1 S1 or AFS B2 S1 and Engine Speed.
Check the A/F sensor voltage 3 times, when the engine is in each of the following conditions:
While idling (check for at least 30 seconds).
At an engine speed of approximately 2500 rpm (without any sudden changes in engine speed).
Raise the engine speed to 4000 rpm and then quickly release the accelerator pedal so that the throttle valve is fully closed.
- Standard Voltage:
Condition
A/F Sensor Voltage Variation
Reference
(1) and (2)
Remains at approximately 3.3 V
3.1 V to 3.5 V
(3)
Increases to 3.8 V or higher
This occurs during engine deceleration
(when fuel-cut performed)
- HINT:
- For more information, see the diagrams below.


- If the output voltage of the A/F sensor remains at approximately 3.3 V (see Malfunction Condition diagram) under any conditions, including those above, the A/F sensor may have an open circuit (this will also happen if the A/F sensor heater has an open circuit).
- If the output voltage of the A/F sensor remains at either approximately 3.8 V or higher, or 2.8 V or less (see Malfunction Condition diagram) under any conditions, including those above, the A/F sensor may have a short circuit.
- The ECM stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the A/F sensor output voltage.
- The ECM must establish a closed throttle valve position learning value to perform fuel cut. If the battery terminal has been reconnected, the vehicle must be driven over 16 km/h (10 mph) to allow the ECM to learn the closed throttle valve position.
- When the vehicle is driven:
The output voltage of the A/F sensor may be below 2.8 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The A/F sensor is functioning normally.
- The A/F sensor is a current output element; therefore, the current is converted into a voltage inside the ECM. Measuring the voltage at the connectors of the A/F sensor or ECM will show a constant voltage result.
- For more information, see the diagrams below.
|
|
||||
| OK | |
| 4. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read pending DTCs.
Result Result
Proceed to
P2195, P2196, P2197 or P2198 is output
A
No DTC is output
B
|
|
||||
| A | |
| 6. REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 7. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read pending DTCs.
Result Result
Proceed to
No DTC is output
A
P2195, P2196, P2197 or P2198 is output
B
|
|
||||
| A | ||
| ||
| 9. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() ![]() |
Disconnect the Air-Fuel Ratio (A/F) sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 (HA1A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA1A) - 4 (A1A-)
Always
10 kΩ or higher
1 (HA2A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA2A) - 4 (A2A-)
Always
10 kΩ or higher
|
|
||||
| OK | |
| 10. INSPECT INTEGRATION NO.1 RELAY (A/F) |
![]() ![]() |
Remove the integration relay from the engine room relay block.
Inspect the A/F fuse.
Remove the A/F fuse from the integration relay.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A/F fuse
Always
Below 1 Ω
Reinstall the A/F fuse.
Inspect the integration relay (A/F).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1C-1 - 1A-4
Battery voltage not applied to terminals 1A-2 and 1A-3
10 kΩ or higher
Battery voltage applied to terminals 1A-2 and 1A-3
Below 1 Ω
|
|
||||
| OK | |
| 11. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() ![]() |
Disconnect the A/F sensor connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C22-2 (+B) - Body ground
Engine switch on (IG)
11 to 14 V
C23-2 (+B) - Body ground
Engine switch on (IG)
11 to 14 V
Turn the engine switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (for LHD):
Tester Connection
Condition
Specified Condition
C22-1 (HA1A) - C45-22 (HA1A)
Always
Below 1 Ω
C22-3 (A1A+) - C45-126 (A1A+)
Always
Below 1 Ω
C22-4 (A1A-) - C45-125 (A1A-)
Always
Below 1 Ω
C23-1 (HA2A) - C45-20 (HA2A)
Always
Below 1 Ω
C23-3 (A2A+) - C45-103 (A2A+)
Always
Below 1 Ω
C23-4 (A2A-) - C45-102 (A2A-)
Always
Below 1 Ω
C22-1 (HA1A) or C45-22 (HA1A) - Body ground
Always
10 kΩ or higher
C22-3 (A1A+) or C45-126 (A1A+) - Body ground
Always
10 kΩ or higher
C22-4 (A1A-) or C45-125 (A1A-) - Body ground
Always
10 kΩ or higher
C23-1 (HA2A) or C45-20 (HA2A) - Body ground
Always
10 kΩ or higher
C23-3 (A2A+) or C45-103 (A2A+) - Body ground
Always
10 kΩ or higher
C23-4 (A2A-) or C45-102 (A2A-) - Body ground
Always
10 kΩ or higher
- Standard Resistance (for RHD):
Tester Connection
Condition
Specified Condition
C22-1 (HA1A) - C46-22 (HA1A)
Always
Below 1 Ω
C22-3 (A1A+) - C46-126 (A1A+)
Always
Below 1 Ω
C22-4 (A1A-) - C46-125 (A1A-)
Always
Below 1 Ω
C23-1 (HA2A) - C46-20 (HA2A)
Always
Below 1 Ω
C23-3 (A2A+) - C46-103 (A2A+)
Always
Below 1 Ω
C23-4 (A2A-) - C46-102 (A2A-)
Always
Below 1 Ω
C22-1 (HA1A) or C46-22 (HA1A) - Body ground
Always
10 kΩ or higher
C22-3 (A1A+) or C46-126 (A1A+) - Body ground
Always
10 kΩ or higher
C22-4 (A1A-) or C46-125 (A1A-) - Body ground
Always
10 kΩ or higher
C23-1 (HA2A) or C46-20 (HA2A) - Body ground
Always
10 kΩ or higher
C23-3 (A2A+) or C46-103 (A2A+) - Body ground
Always
10 kΩ or higher
C23-4 (A2A-) or C46-102 (A2A-) - Body ground
Always
10 kΩ or higher


|
|
||||
| OK | |
| 12. REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 13. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 14. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read pending DTCs.
Result Result
Proceed to
No DTC is output
A
P2195, P2196, P2197 or P2198 is output
B
|
|
||||
| A | ||
| ||







