2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

CAUTION / NOTICE / HINT


DESCRIPTION

Refer to DTC P2195 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
P2237
P2240
An open in the circuit between terminals AF+ and AF- of the A/F sensor while the engine is running (2 trip detection logic).
  1. Open in Air Fuel Ratio (A/F) sensor (for bank 1, 2 sensor 1) circuit
  2. Air Fuel Ratio (A/F) sensor (for bank 1, 2 sensor 1)
  3. ECM
P2238
P2241
  1. Case 1:
Condition (a) or (b) continues for 5.0 seconds or more (1 trip detection logic):
(a) The AF+ voltage is 0.5 V or less.
(b) (AF+) - (AF-) = 0.1 V or less.
  1. Case 2:
The A/F sensor admittance is less than 0.022 1/Ω (2 trip detection logic).
  1. Open or short in A/F sensor (for bank 1, 2 sensor 1) circuit
  2. A/F sensor (for bank 1, 2 sensor 1)
  3. ECM
P2239
P2242
The AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
  1. Open or short in A/F sensor (for bank 1, 2 sensor 1) circuit
  2. A/F sensor (for bank 1, 2 sensor 1)
  3. ECM
P2252
P2255
The AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic).
  1. Open or short in A/F sensor (for bank 1, 2 sensor 1) circuit
  2. A/F sensor (for bank 1, 2 sensor 1)
  3. ECM
P2253
P2256
The AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
  1. Open or short in A/F sensor (for bank 1, 2 sensor 1) circuit
  2. A/F sensor (for bank 1, 2 sensor 1)
  3. ECM

HINT:
  1. DTCs P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 A/F sensor circuit.
  2. DTCs P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 A/F sensor circuit.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder.
  4. Bank 2 refers to the bank that includes the No. 2 cylinder.


MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the A/F sensor circuit, or if the A/F sensor output drops.
To detect these problems, the voltage of the A/F sensor is monitored when turning the engine switch on (IG), and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the A/F sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is outside of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the A/F sensor. If the same malfunction is detected in the next driving cycle, the MIL is illuminated and a DTC is stored.
The Air-Fuel Ratio (A/F) sensor varies its output voltage in proportion to the air-fuel ratio. If the A/F sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the A/F sensor circuit.

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. (a) Connect the intelligent tester to the DLC3.
  2. (b) Start the engine and turn the tester on.
  3. (c) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. (d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/ F sensor.
  5. (e) Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  6. (f) Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  1. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Standard:
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1 S1
(A/F)
+25%
Rich
Below 3.0
-12.5%
Lean
Higher than 3.35
O2S B1 S2
(HO2)
+25%
Rich
Higher than 0.55
-12.5%
Lean
Below 0.4
AFS B2 S1
(A/F)
+25%
Rich
Below 3.0
-12.5%
Lean
Higher than 3.35
O2S B2 S2
(HO2)
+25%
Rich
Higher than 0.55
-12.5%
Lean
Below 0.4

NOTICE:
The A/F sensor has an output delay of a few seconds and the HO2 sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E02
A150787E01
A150788E04
-
2
A150787E01
A150790E01
A150787E01
A150788E04
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E02
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leakage from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the output voltages of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A182483E02
  1. Disconnect the A/F sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-2 (+B) - Body ground
    Engine switch on (IG)
    11 to 14 V
    C23-2 (+B) - Body ground
    Engine switch on (IG)
    11 to 14 V

  1. Turn the engine switch off.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C22-1 (HA1A) - C45-22 (HA1A)
    Always
    Below 1 Ω
    C22-3 (A1A+) - C45-126 (A1A+)
    Always
    Below 1 Ω
    C22-4 (A1A-) - C45-125 (A1A-)
    Always
    Below 1 Ω
    C23-1 (HA2A) - C45-20 (HA2A)
    Always
    Below 1 Ω
    C23-3 (A2A+) - C45-103 (A2A+)
    Always
    Below 1 Ω
    C23-4 (A2A-) - C45-102 (A2A-)
    Always
    Below 1 Ω
    C22-1 (HA1A) or C45-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    C22-3 (A1A+) or C45-126 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C22-4 (A1A-) or C45-125 (A1A-) - Body ground
    Always
    10 kΩ or higher
    C23-1 (HA2A) or C45-20 (HA2A) - Body ground
    Always
    10 kΩ or higher
    C23-3 (A2A+) or C45-103 (A2A+) - Body ground
    Always
    10 kΩ or higher
    C23-4 (A2A-) or C45-102 (A2A-) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C22-1 (HA1A) - C46-22 (HA1A)
    Always
    Below 1 Ω
    C22-3 (A1A+) - C46-126 (A1A+)
    Always
    Below 1 Ω
    C22-4 (A1A-) - C46-125 (A1A-)
    Always
    Below 1 Ω
    C23-1 (HA2A) - C46-20 (HA2A)
    Always
    Below 1 Ω
    C23-3 (A2A+) - C46-103 (A2A+)
    Always
    Below 1 Ω
    C23-4 (A2A-) - C46-102 (A2A-)
    Always
    Below 1 Ω
    C22-1 (HA1A) or C46-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    C22-3 (A1A+) or C46-126 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C22-4 (A1A-) or C46-125 (A1A-) - Body ground
    Always
    10 kΩ or higher
    C23-1 (HA2A) or C46-20 (HA2A) - Body ground
    Always
    10 kΩ or higher
    C23-3 (A2A+) or C46-103 (A2A+) - Body ground
    Always
    10 kΩ or higher
    C23-4 (A2A-) or C46-102 (A2A-) - Body ground
    Always
    10 kΩ or higher

    A164715E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read pending DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output
    B



B
REPLACE ECM (Click here)
A

END


← P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) (+ P2196, P2197, P2198) (Sep 2011 – Dec 2011)P2431 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1 (+ P2432, P2433) (Sep 2011 – Dec 2011) →