2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

MIL Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detections by the ECM. When the engine switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.
The MIL operation can be checked visually: When the engine switch is first turned on (IG), the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A185396E01

INSPECTION PROCEDURE


1. CHECK THAT MIL IS ILLUMINATED
  1. Check the MIL illumination condition.

    Result 
    Result
    Proceed to
    MIL remains on
    A
    MIL does not illuminate
    B
    MIL remains on → MIL turns off
    C



B
Go to step 5

C
SYSTEM OK
A


2. CHECK WHETHER MIL TURNS OFF
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Check if any DTCs have been stored. Note down any DTCs.

  1. Clear DTCs (Click here).

  1. Check if the MIL turns off.

    OK:
    MIL turns off.



NG
Go to step 3
OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

3. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
A164768E07
  1. Disconnect the ECM connector.

  1. Turn the engine switch on (IG).

  1. Check that the MIL is not illuminated.

    OK:
    MIL is not illuminated.



NG
Go to step 4
OK

REPLACE ECM (Click here)

4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
A185397E01
  1. Disconnect the ECM connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    A38-24 (W) or E8-12 (CHK) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    A52-24 (W) or E8-12 (CHK) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (w/ Multi-information Display)
    B
    OK (w/o Multi-information Display)
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

5. CHECK THAT MIL IS ILLUMINATED
  1. Check if the MIL is illuminated when the engine switch is turned on (IG).

    OK:
    MIL is illuminated.



NG
Go to step 6
OK

SYSTEM OK

6. CHECK THAT ENGINE STARTS
  1. Turn the engine switch on (IG).

  1. Start the engine.

    Result 
    Result
    Proceed to
    Engine starts
    A
    Engine does not start*
    B

    HINT:
    *: The intelligent tester cannot communicate with the ECM.



B
GO TO VC OUTPUT CIRCUIT (Click here)
A


7. CHECK HARNESS AND CONNECTOR (W VOLTAGE)
A164768E07
  1. Disconnect the ECM connector.

  1. Disconnect the combination meter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for LHD):
    Tester Connection
    Switch Condition
    Specified Condition
    A38-24 (W) - Body ground
    Engine switch on (IG)
    11 to 14 V

    Standard Voltage (for RHD):
    Tester Connection
    Switch Condition
    Specified Condition
    A52-24 (W) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 8
OK

REPLACE ECM (Click here)

8. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
A185397E01
  1. Disconnect the ECM connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    A38-24 (W) - E8-12 (CHK)
    Always
    Below 1 Ω

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    A52-24 (W) - E8-12 (CHK)
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK (w/ Multi-information Display)
    B
    OK (w/o Multi-information Display)
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← Brake Override System (Sep 2011 – Dec 2011)PARTS LOCATION (Sep 2011 – Dec 2011) →