2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

VC Output Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
A116143E68
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the engine switch is first turned on (IG). The MIL turns off when the engine is started.


WIRING DIAGRAM

A181340E01
A181340E02

INSPECTION PROCEDURE


1. CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) illuminates up when turning the engine switch on (IG).

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
SYSTEM OK
A


2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and tester on.

  1. Check the communication between the tester and ECM.

    Result 
    Result
    Proceed to
    Communication is not possible
    A
    Communication is possible
    B



B
GO TO MIL CIRCUIT (Click here)
A


3. CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle body connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE THROTTLE BODY ASSEMBLY (Click here)
A


4. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (Click here)
A


5. CHECK MIL (POWER STEERING OIL PRESSURE SWITCH)
  1. Disconnect the power steering oil pressure sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE POWER STEERING OIL PRESSURE SWITCH (Click here)
A


6. CHECK MIL (CAMSHAFT POSITION SENSOR)
  1. Disconnect the camshaft position sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE CAM POSITION SENSOR ASSEMBLY (Click here)
A


7. CHECK MIL (AIR PRESSURE SENSOR)
  1. Disconnect the air pressure sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE AIR PRESSURE SENSOR (Click here)
A


8. CHECK HARNESS AND CONNECTOR
  1. Disconnect the throttle body connector.

  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the air pressure sensor connector.

  1. Disconnect the power steering oil pressure switch connector.

  1. Disconnect the camshaft position sensor connector.

  1. A164740E06
    Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C45-80 (VCTA) - Body ground
    Always
    10 kΩ or higher
    A38-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A38-59 (VCP2) - Body ground
    Always
    10 kΩ or higher
    C45-66 (VC) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C45-80 (VCTA) - Body ground
    Always
    10 kΩ or higher
    A52-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A52-59 (VCP2) - Body ground
    Always
    10 kΩ or higher
    C45-66 (VC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


10. CHECK PROBLEM SYMPTOM DISAPPEARS
  1. Check if the problem symptom disappears.

    Result 
    Result
    Proceed to
    Problem symptom disappears
    A
    Problem symptom does not disappear
    B



B
GO TO PROBLEM SYMPTOMS TABLE (Click here)
A

END


← ECM Power Source Circuit (Sep 2011 – Dec 2011)Fuel Pump Control Circuit (Sep 2011 – Dec 2011) →