2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

Starter Signal Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch to clutch start switch and also flows to terminal STA of the ECM (STA Signal).

WIRING DIAGRAM

Refer to DTC P0617 (Click here).

INSPECTION PROCEDURE


1. READ VALUE USING GTS (STARTER SIGNAL)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read values.

  1. Check the result when the ignition switch is turned to ON and when the engine is started.

    OK:
    Condition
    Display (Starter Signal)
    Ignition switch ON
    OFF
    Engine is started
    ON



NG
Go to step 6
OK


2. INSPECT STARTER RELAY (ST)
  1. Inspect the starter relay (ST) (Click here).



NG
REPLACE STARTER RELAY (ST)
OK


3. CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH)
A266613E01
  1. Disconnect the clutch start switch.

  1. Remove the ST relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    ST relay (1) - A49-2
    Always
    Below 1 Ω
    ST relay (1) or A49-2 - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    ST relay (1) - e1-2
    Always
    Below 1 Ω
    ST relay (1) or e1-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A162331E02
  1. Remove the ST relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    ST relay (2) - ST relay (5)
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY (ST) - BATTERY, BODY GROUND)
OK


5. INSPECT STARTER
  1. Inspect the starter (Click here).



NG
REPLACE STARTER (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER - STARTER RELAY (ST), BATTERY)

6. INSPECT CLUTCH START SWITCH ASSEMBLY
  1. Inspect the clutch start switch (for LHD) (Click here).

  1. Inspect the clutch start switch (for RHD) (Click here).

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)

C
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)
A


7. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ECM)
A266612E02
  1. Disconnect the clutch start switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A49-2 - A38-46 (STA)
    Always
    Below 1 Ω
    A49-2 or A38-46 (STA) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    e1-2 - A52-46 (STA)
    Always
    Below 1 Ω
    e1-2 or A52-46 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
Result 
Result
Proceed to
w/ Entry and Start System
A
w/o Entry and Start System
B


B
Go to step 11
A


9. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the starter operation.

    OK:
    Malfunction has been repaired successfully.



NG
GO TO ENTRY AND START SYSTEM (ENGINE DOES NOT START) (Click here)
OK

END

11. INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


12. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - IGNITION SWITCH)
A157741E25
  1. Disconnect the clutch start switch connector.

  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A49-1 - E93-3 (ST1)
    Always
    Below 1 Ω
    A49-1 or E93-3 (ST1) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    e1-1 - E93-3 (ST1)
    Always
    Below 1 Ω
    e1-1 or E93-3 (ST1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)


← Starter Signal Circuit (Sep 2011 – Dec 2011)Cranking Holding Function Circuit (Sep 2011 – Dec 2011) →