B2275 STSW Monitor Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
This DTC is stored when the engine start request signal circuit inside the main body ECU is open or shorted.| DTC Code |
Detection Condition |
Trouble Area |
| B2275 |
The engine start request signal circuit inside the main body ECU or other related circuit is malfunctioning. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK WHETHER DTC OUTPUT RECURS |
Clear the DTCs (Click here).
Depress the brake pedal (for A/T) or clutch pedal (for M/T) with the engine switch on (IG), wait at least 15 seconds, and check whether DTC B2275 is output.
Result Result
Proceed to
DTC B2275 output
A
No DTC output
B
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM) |


Disconnect the E4 main body ECU connector.
Disconnect the A38 (for LHD) or A52 (for RHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (except 1VD-FTV w/ DPF):
Tester Connection
Condition
Specified Condition
E4-4 (STSW) - A38-14 (STSW)*1
E4-4 (STSW) - A52-14 (STSW)*2
Always
Below 1 Ω
E4-4 (STSW) or A38-14 (STSW) - Body ground*1
E4-4 (STSW) or A52-14 (STSW) - Body ground*2
Always
10 kΩ or higher
- HINT:
- *1: for LHD
- *2: for RHD
- Standard Resistance (for 1VD-FTV w/ DPF):
Tester Connection
Condition
Specified Condition
E4-4 (STSW) - A38-47 (STSW)*1
E4-4 (STSW) - A52-47 (STSW)*2
Always
Below 1 Ω
E4-4 (STSW) or A38-47 (STSW) - Body ground*1
E4-4 (STSW) or A52-47 (STSW) - Body ground*2
Always
10 kΩ or higher
- HINT:
- *1: for LHD
- *2: for RHD
|
|
||||
| OK | |
| 3. INSPECT MAIN BODY ECU |
![]() ![]() |
Measure the voltage according to the value(s) in the table below.
- HINT:
- The voltage is generated at terminal STSW for 0.3 seconds when the engine cranks.
- Standard Voltage (for A/T):
Tester Connection
Condition
Specified Condition
E4-4 (STSW) - Body ground
Brake pedal depressed with shift lever in P, engine switch pushed once
11 to 14 V
- Standard Voltage (for M/T):
Tester Connection
Condition
Specified Condition
E4-4 (STSW) - Body ground
Clutch pedal depressed, engine switch pushed once
11 to 14 V
Result Result
Proceed to
Outside specified range
A
Within specified range (for 1GR-FE)
B
Within specified range (for 1UR-FE)
C
Within specified range (for 3UR-FE)
D
Within specified range (for 1VD-FTV)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||

