2011-2013 Land Cruiser · Service Manual Vehicle Interior

B2276 ACCR Signal Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when a malfunction is detected in the ACCR signal output by the main body ECU.
DTC Code
Detection Condition
Trouble Area
B2276
The ACCR output circuit inside the main body ECU or other related circuit is malfunctioning.
  1. Main body ECU
  2. ECM
  3. Harness or connector

WIRING DIAGRAM

C162997E17

INSPECTION PROCEDURE


1. CHECK WHETHER DTC OUTPUT RECURS
  1. Clear the DTCs (Click here).

  1. Check whether DTC B2276 is output 50 seconds or more after the engine switch is turned on (IG).

    Result 
    Result
    Proceed to
    DTC B2276 output
    A
    No DTC output
    B



B
USE SIMULATION METHOD TO CHECK (SYSTEM IS OK) (Click here)
A


2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
A184840E02
  1. Disconnect the E2 main body ECU connector.

  1. Disconnect the A38 (for LHD) or A52 (for RHD) ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for 2UZ-FE, 3UR-FE):
    Tester Connection
    Condition
    Specified Condition
    E2-3 (ACCR) - A38-41 (ACCR)*1
    E2-3 (ACCR) - A52-41 (ACCR)*2
    Always
    Below 1 Ω
    E2-3 (ACCR) or A38-41 (ACCR) - Body ground*1
    E2-3 (ACCR) or A52-41 (ACCR) - Body ground*2
    Always
    10 kΩ or higher

    HINT:
    *1: for LHD
    *2: for RHD

    Standard Resistance (for 1GR-FE, 1VD-FTV):
    Tester Connection
    Condition
    Specified Condition
    E2-3 (ACCR) - A38-13 (ACCR)*1
    E2-3 (ACCR) - A52-13 (ACCR)*2
    Always
    Below 1 Ω
    E2-3 (ACCR) or A38-13 (ACCR) - Body ground*1
    E2-3 (ACCR) or A52-13 (ACCR) - Body ground*2
    Always
    10 kΩ or higher

    HINT:
    *1: for LHD
    *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT MAIN BODY ECU
A177595E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E2-3 (ACCR) - Body ground
    Engine switch pressed and engine cranking
    11 to 14 V

Result 
Result
Proceed to
Outside specified range
A
Within specified range (for 1GR-FE)
B
Within specified range (for 2UZ-FE)
C
Within specified range (for 3UR-FE)
D
Within specified range (for 1VD-FTV)
E


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPLACE ECM (Click here)
A

REPLACE MAIN BODY ECU


← B2275 STSW Monitor Malfunction (from Jan 2012)B2276 ACCR Signal Circuit Malfunction (from Jan 2012) →