Rear Power Window LH does not Operate with Rear Power Window Switch LH
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
- If the manual up/down function does not operate, there may be a malfunction in the rear power window regulator switch, power window rear regulator motor LH, harness or connector.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK LIN COMMUNICATION SYSTEM |
Check for LIN communication system DTCs related to the power window control system (Click here).
- OK:
- LIN communication system DTCs are not output.
|
|
||||
| OK | |
| 2. CHECK FOR DTC (B2312) |
Check if DTC B2312 is output (Click here).
- OK:
- DTC B2312 is not output.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR LH) |
Use the Data List to check if the power window regulator motor is functioning properly (Click here).
RL-Door Motor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RL Door P/W Up SW
Rear power window LH manual up signal / ON or OFF
ON: Rear power window LH manual up switch operated
OFF: Rear power window LH switch not operated
-
RL Door P/W Down SW
Rear power window LH manual down signal / ON or OFF
ON: Rear power window LH manual down switch operated
OFF: Rear power window LH switch not operated
-
- OK:
- The display changes according to operation of the rear power window switch LH.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - BODY GROUND) |
Disconnect the J10 switch connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
J10-1 (GND) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR LH - BATTERY AND BODY GROUND) |
![]() ![]() |
Disconnect the J11 motor connector.
Measure the voltage and resistance according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
J11-2 (B) - Body ground
Always
11 to 14 V
- Standard Resistance:
Tester Connection
Condition
Specified Condition
J11-1 (GND) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH) |
Disconnect the J10 switch connector.

Disconnect the J11 motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
J10-6 (UP) - J11-10 (UP)
Always
Below 1 Ω
J10-7 (DOWN) - J11-7 (DOWN)
Always
Below 1 Ω
J10-8 (AUTO) - J11-4 (AUTO)
Always
Below 1 Ω
J10-6 (UP) or J11-10 (UP) - Body ground
Always
10 kΩ or higher
J10-7 (DOWN) or J11-7 (DOWN) - Body ground
Always
10 kΩ or higher
J10-8 (AUTO) or J11-4 (AUTO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH |
![]() ![]() |
Remove the rear power window regulator switch (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
J10-6 (UP) - J10-1 (GND)
Manual up operation
Below 1 Ω
J10-7 (DOWN) - J10-1 (GND)
Manual down operation
Below 1 Ω
|
|
||||
| OK | ||
| ||


