2011-2013 Land Cruiser · Service Manual Vehicle Exterior

B2312 Power Window Switch Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The power window regulator motor consists of the motor, regulator and ECU. The power window regulator motor is driven by operating the power window switch.
This DTC is stored when the ECU built into the regulator motor determines that the power window switch is stuck.

HINT:
This DTC may be stored for all the windows.

NOTICE:
  1. When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
  2. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:
    1. Close the power window by fully pulling up the power window switch and holding it in the auto up position.
    2. Open the power window by fully pushing down the power window switch.

Multiplex Network Master Switch 
DTC Code
DTC Detection Condition
Trouble Area
B2312
  1. The multiplex network master switch is stuck.
  2. The multiplex network master switch is held in the same position for more than 20 sec.
  1. Multiplex network master switch
  2. Harness or connector
  3. Multiplex network master switch held in same position for more than 20 sec.
Front Power Window Regulator Motor LH 
DTC Code
DTC Detection Condition
Trouble Area
B2312
  1. The multiplex network master switch is stuck.
  2. The multiplex network master switch is held in the same position for more than 20 sec.
  1. Multiplex network master switch
  2. Power window regulator motor
  3. Harness or connector
  4. Multiplex network master switch held in same position for more than 20 sec.
Front Power Window Regulator Motor RH 
DTC Code
DTC Detection Condition
Trouble Area
B2312
  1. The power window regulator switch is stuck.
  2. The power window regulator switch is held in same position for more than 20 sec.
  1. Power window regulator switch
  2. Power window regulator motor
  3. Harness or connector
  4. Power window regulator switch held in same position for more than 20 sec.
Rear Power Window Regulator Motor LH 
DTC Code
DTC Detection Condition
Trouble Area
B2312
  1. The power window regulator switch is stuck.
  2. The power window regulator switch is held in same position for more than 20 sec.
  1. Power window regulator switch
  2. Power window regulator motor
  3. Harness or connector
  4. Power window regulator switch held in same position for more than 20 sec.
Rear Power Window Regulator Motor RH 
DTC Code
DTC Detection Condition
Trouble Area
B2312
  1. The power window regulator switch is stuck.
  2. The power window regulator switch is held in same position for more than 20 sec.
  1. Power window regulator switch
  2. Power window regulator motor
  3. Harness or connector
  4. Power window regulator switch held in same position for more than 20 sec.

WIRING DIAGRAM

B180278E02
B180279E10
B180279E02
B180279E03

INSPECTION PROCEDURE


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    B2312 is output.
    A
    LIN communication DTCs are output.
    B
    No DTCs output.
    C



B
GO TO LIN COMMUNICATION SYSTEM (Click here)

C
END (DUE TO KEEPING SWITCH OPERATED FOR 20 SEC. OR MORE)
A


3. CHECK MALFUNCTION LOCATION
  1. Check where DTC B2312 is output from.

    Result 
    Result
    Proceed to
    B2312 output from multiplex network master switch.
    A
    B2312 output from driver side power window regulator motor.
    B
    B2312 output from passenger side power window regulator motor.
    C
    B2312 output from rear power window regulator motor LH.
    D
    B2312 output from rear power window regulator motor RH.
    E



B
Go to step 4

C
Go to step 6

D
Go to step 9

E
Go to step 12
A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)

4. READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE POWER WINDOW REGULATOR MOTOR)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver side power window auto up/down signal / ON or OFF
    ON: Driver side power window auto up/down switch operated
    OFF: Driver side power window switch not operated
    -
    D Door P/W Up SW
    Driver side power window manual up signal / ON or OFF
    ON: Driver side power window manual up switch operated
    OFF: Driver side power window switch not operated
    -
    D Door P/W Down SW
    Driver side power window manual down signal / ON or OFF
    ON: Driver side power window manual down switch operated
    OFF: Driver side power window switch not operated
    -
    Result 
    Result
    Proceed to
    The display does not change according to operation of the multiplex network master switch.
    A
    The display changes according to operation of the multiplex network master switch (for LHD).
    B
    The display changes according to operation of the multiplex network master switch (for RHD).
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
A


5. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR AND BODY GROUND)

  1. B184458E02
    Disconnect I11*1 or I22*2 switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect I12*1 or I4*2 motor connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I11-20 (UP) - I12-10 (UP)
    Always
    Below 1 Ω
    I11-15 (DOWN) - I12-7 (DOWN)
    Always
    Below 1 Ω
    I11-20 (UP) or I12-10 (UP) - Body ground
    Always
    10 kΩ or higher
    I11-15 (DOWN) or I12-7 (DOWN) - Body ground
    Always
    10 kΩ or higher

    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I22-20 (UP) - I4-10 (UP)
    Always
    Below 1 Ω
    I22-15 (DOWN) - I4-7 (DOWN)
    Always
    Below 1 Ω
    I22-20 (UP) or I4-10 (UP) - Body ground
    Always
    10 kΩ or higher
    I22-15 (DOWN) or I4-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

6. READ VALUE USING INTELLIGENT TESTER (FRONT PASSENGER SIDE POWER WINDOW REGULATOR MOTOR)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger side power window auto up/down signal / ON or OFF
    ON: Front passenger side power window auto up/down switch operated
    OFF: Front passenger side power window regulator switch not operated
    -
    P Door P/W Up SW
    Front passenger side power window manual up signal / ON or OFF
    ON: Front passenger side power window manual up switch operated
    OFF: Front passenger side power window regulator switch not operated
    -
    P Door P/W Down SW
    Front passenger side power window manual down signal / ON or OFF
    ON: Front passenger side power window manual down switch operated
    OFF: Front passenger side power window regulator switch not operated
    -
    Result 
    Result
    Proceed to
    The display does not change according to operation of the power window regulator switch.
    A
    The display changes according to operation of the power window regulator switch (for LHD).
    B
    The display changes according to operation of the power window regulator switch (for RHD).
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
A


7. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

  1. B184772E04
    Remove the power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    I3-6 (UP) - I3-1 (GND)
    Manual up operation
    Below 1 Ω
    I3-7 (DOWN) - I3-1 (GND)
    Manual down operation
    Below 1 Ω
    I3-8 (AUTO) - I3-1 (GND)
    Auto up/down operation
    Below 1 Ω
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    I25-6 (UP) - I25-1 (GND)
    Manual up operation
    Below 1 Ω
    I25-7 (DOWN) - I25-1 (GND)
    Manual down operation
    Below 1 Ω
    I25-8 (AUTO) - I25-1 (GND)
    Auto up/down operation
    Below 1 Ω



NG
REPLACE FRONT PASSENGER SIDE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR)

  1. B184455E09
    Disconnect the I3*1 or I25*2 switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the I4*1 or I12*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I3-6 (UP) - I4-10 (UP)
    Always
    Below 1 Ω
    I3-7 (DOWN) - I4-7 (DOWN)
    Always
    Below 1 Ω
    I3-8 (AUTO) - I4-4 (AUTO)
    Always
    Below 1 Ω
    I3-6 (UP) or I4-10 (UP) - Body ground
    Always
    10 kΩ or higher
    I3-7 (DOWN) or I4-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    I3-8 (AUTO) or I4-4 (AUTO) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I25-6 (UP) - I12-10 (UP)
    Always
    Below 1 Ω
    I25-7 (DOWN) - I12-7 (DOWN)
    Always
    Below 1 Ω
    I25-8 (AUTO) - I12-4 (AUTO)
    Always
    Below 1 Ω
    I25-6 (UP) or I12-10 (UP) - Body ground
    Always
    10 kΩ or higher
    I25-7 (DOWN) or I12-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    I25-8 (AUTO) or I12-4 (AUTO) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

9. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    RL-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RL Door P/W Auto SW
    Rear power window LH auto up/down signal / ON or OFF
    ON: Rear power window LH auto up/down switch operated
    OFF: Rear power window LH switch not operated
    -
    RL Door P/W Up SW
    Rear power window LH manual up signal / ON or OFF
    ON: Rear power window LH manual up switch operated
    OFF: Rear power window LH switch not operated
    -
    RL Door P/W Down SW
    Rear power window LH manual down signal / ON or OFF
    ON: Rear power window LH manual down switch operated
    OFF: The rear power window LH switch not operated
    -

    OK:
    The display changes according to operation of the rear power window regulator switch.



NG
Go to step 10
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)

10. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
B184772E02
  1. Remove the rear power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J10-6 (UP) - J10-1 (GND)
    Manual up operation
    Below 1 Ω
    J10-7 (DOWN) - J10-1 (GND)
    Manual down operation
    Below 1 Ω
    J10-8 (AUTO) - J10-1 (GND)
    Auto up/down operation
    Below 1 Ω



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (Click here)
OK


11. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - POWER WINDOW REGULATOR MOTOR)

  1. B184455E02
    Disconnect the J10 switch connector.

  1. Disconnect the J11 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J10-6 (UP) - J11-10 (UP)
    Always
    Below 1 Ω
    J10-7 (DOWN) - J11-7 (DOWN)
    Always
    Below 1 Ω
    J10-8 (AUTO) - J11-4 (AUTO)
    Always
    Below 1 Ω
    J10-6 (UP) or J11-10 (UP) - Body ground
    Always
    10 kΩ or higher
    J10-7 (DOWN) or J11-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    J10-8 (AUTO) or J11-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)

12. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR RH)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    RR-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door P/W Auto SW
    Rear power window RH auto up/down signal / ON or OFF
    ON: The rear power window RH auto up/down switch operated
    OFF: The rear power window RH switch not operated
    -
    RR Door P/W Up SW
    Rear power window RH manual up signal / ON or OFF
    ON: The rear power window RH manual up switch operated
    OFF: The rear power window RH switch not operated
    -
    RR Door P/W Down SW
    Rear power window RH manual down signal / ON or OFF
    ON: The rear power window RH manual down switch operated
    OFF: The rear power window RH switch not operated
    -

    OK:
    The display changes according to operation of the rear power window regulator switch RH.



NG
Go to step 13
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)

13. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
B184772E03
  1. Remove the rear power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J3-6 (UP) - J3-1 (GND)
    Manual up operation
    Below 1 Ω
    J3-7 (DOWN) - J3-1 (GND)
    Manual down operation
    Below 1 Ω
    J3-8 (AUTO) - J3-1 (GND)
    Auto up/down operation
    Below 1 Ω



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK


14. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BODY GROUND)
B184455E08
  1. Disconnect the J3 switch connector.

  1. Disconnect the J4 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J3-6 (UP) - J4-10 (UP)
    Always
    Below 1 Ω
    J3-7 (DOWN) - J4-7 (DOWN)
    Always
    Below 1 Ω
    J3-8 (AUTO) - J4-4 (AUTO)
    Always
    Below 1 Ω
    J3-6 (UP) or J4-10 (UP) - Body ground
    Always
    10 kΩ or higher
    J3-7 (DOWN) or J4-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    J3-8 (AUTO) or J4-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)


← B2312 Power Window Switch Malfunction (Sep 2011 – Dec 2011)B2313 Glass Position Initialization Incomplete (Sep 2011 – Dec 2011) →