2011-2013 Land Cruiser · Service Manual Brake

C1425 Open in Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

DESCRIPTION

The skid control ECU (master cylinder solenoid) has an open detection circuit, which stores this DTC when detecting an open in the stop light switch input line or the ground line of the stop light switch circuit with the stop light switch off (brake pedal not depressed).
DTC Code
DTC Detection Condition
Trouble Area
C1425
When the IG1 terminal voltage is between 9.5 and 17.4 V, an open in the STP terminal circuit continues for 3 seconds or more.
  1. Stop light switch circuit
  2. Stop light control relay assembly
  3. Stop light control relay circuit
  4. Skid control ECU (Master cylinder solenoid)

WIRING DIAGRAM

C246896E04

INSPECTION PROCEDURE

NOTICE:
After replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. READ VALUE USING GTS (STOP LIGHT SW)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch condition observed on the GTS changes according to brake pedal operation.

    OK:
    The GTS displays ON and OFF according to brake pedal operation.



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3. CHECK HARNESS AND CONNECTOR (STP TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (master cylinder solenoid) connector.

  1. C214161E71
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A24-7 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Master Cylinder Solenoid])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (+B/GND TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the stop light control relay assembly connector.

  1. C206543E13
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A39-6 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-4 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Control Relay Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (STP TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the stop light control relay assembly connector.

  1. C206543E14
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A39-2 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Control Relay Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (OUT TERMINAL)
  1. Reconnect the stop light control relay assembly connector.

  1. E205929E05
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A39-8 (OUT) - Body ground
    Brake pedal depressed
    8 to 14 V
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (Stop Light Control Relay Assembly)



NG
REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY
OK


7. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)


← C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction (from Jan 2012)C1452 Accumulator Low Pressure (from Jan 2012) →