C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
Refer to DTCs C1421, C1423 and C1424 (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1422 |
When the stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the master cylinder solenoid, perform zero point calibration (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- After replacing the master cylinder solenoid, perform zero point calibration (Click here).
| 1. READ VALUE USING GTS (STOP LIGHT SW) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Check that the stop light switch condition observed on the GTS changes according to brake pedal operation.
- OK:
- The GTS displays ON and OFF according to brake pedal operation.
|
|
||||
| OK | |
| 2. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch installation (for LHD: Click here, for RHD: Click here).
- OK:
- The brake pedal height and stop light switch installation are normal.
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output (for LHD)
B
DTC is output (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH POWER SOURCE TERMINAL) |
Make sure that there is no looseness in the locking part and connecting part of the connectors.
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
A30-2 - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Stop Light Switch Assembly)
|
|
||||
| OK | |
| 5. INSPECT STOP LIGHT SWITCH |
Remove the stop light switch assembly (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Switch pin not pushed in
Below 1 Ω
Switch pin pushed in
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Stop Light Switch Assembly)
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (STP TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A24-7 (STP) - Body ground
Brake pedal depressed
8 to 14 V
Brake pedal released
Below 1.5 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
