C1434 Steering Angle Sensor Output Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
Steering sensor signals are sent to the skid control ECU (master cylinder solenoid) via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering sensor zero point malfunction diagnostic function.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1434 |
An error in communication between the skid control ECU and the steering sensor, or an abnormal steering sensor zero point. |
|
WIRING DIAGRAM
Refer to DTC C1432 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the steering sensor, confirm that the replacement part is of the correct specification.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the steering sensor, confirm that the replacement part is of the correct specification.
- HINT:
- When any of the speed sensors or the yaw rate sensor assembly has trouble, DTCs for the steering sensor may be stored even when the steering sensor is normal. When DTCs for the speed sensors or yaw rate sensor assembly are output together with DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate sensor assembly first, and then inspect and repair the steering sensor.
| 1. CHECK DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTC is output (Click here).
Start the engine.
Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left, and then check that no speed sensor or yaw rate sensor assembly DTCs are output (Click here).
Result Result
Proceed to
No CAN communication system, speed sensor, or yaw rate sensor assembly DTCs are output
A
CAN communication system DTC is output (for LHD)
B
CAN communication system DTC is output (for RHD)
C
Speed sensor or yaw rate sensor assembly DTC is output
D
- HINT:
- If there is a malfunction in any of the speed sensors or the yaw rate sensor assembly, an abnormal value may be output although the steering sensor is normal.
- If speed sensor and yaw rate sensor assembly DTCs are output simultaneously, repair these two sensors first, and then inspect the steering sensor.
- If there is a malfunction in any of the speed sensors or the yaw rate sensor assembly, an abnormal value may be output although the steering sensor is normal.
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (IG/ESS TERMINAL) |
![]() ![]() |
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connectors.
Disconnect the steering sensor connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E11-1 (IG) - Body ground
Ignition switch ON
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E11-2 (ESS) - Body ground
Always
Below 1 Ω
| *a |
Front view of wire harness connector (to Steering Sensor) |
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (BAT TERMINAL) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the steering sensor connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E11-3 (BAT) - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Steering Sensor)
Result Result
Proceed to
OK
A
NG (w/ VGRS)
B
NG (w/o VGRS)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (+BI TERMINAL) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the steering control ECU connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E77-10 (+BI) - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Steering Control ECU)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (STEERING SENSOR - STEERING CONTROL ECU) |
Turn the ignition switch off.
Disconnect the E11 steering sensor connector.
Disconnect the E79 steering control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E11-3 (BAT) - E79-1 (+BO)
Always
Below 1 Ω
E11-3 (BAT) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||




