2011-2013 Land Cruiser · Service Manual Steering

B2610 Tilt Position Sensor or Tilt Motor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Sep 2011

DESCRIPTION

The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and outputs a signal to the CPU based on that tilt.
C152160E01

HINT:
Limit positions can be confirmed on the screen of the intelligent tester.

DTC Code
Detection Condition
Trouble Area
B2610
The tilt operation stops within the operation range while operating.
  1. Harness or connector
  2. Tilt position sensor or tilt motor
  3. Multiplex tilt and telescopic ECU

WIRING DIAGRAM

C149999E03

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TILT UP/DOWN)
C106468E01
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the steering wheel tilts up and down.

    Tilt & Telescopic 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Tilt Operation
    Tilt operation
    Up/Down
    -

Result 
Result
Proceed to
Steering wheel does not tilt up/down.
A
Steering wheel tilts up/down.
B


B
Go to step 4
A


2. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)
C149089E12
  1. Disconnect the E27 multiplex tilt and telescopic ECU connector.

  1. Disconnect the E17 tilt motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E27-10 (TIM+) - E17-1 (TIM+)
    Always
    Below 1 Ω
    E27-1 (TIM-) - E17-2 (TIM-)
    E27-10 (TIM+) - Body ground
    Always
    10 kΩ or higher
    E27-1 (TIM-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT TILT MOTOR
C149090E05
  1. Apply 12 V battery voltage to the tilt motor connector. Then check the steering wheel tilt operation.

    OK:
    Measurement Condition
    Specified Condition
    12 V battery positive (+) lead → Terminal E17-1 (TIM+)
    12 V battery negative (-) lead → Terminal E17-2 (TIM-)
    The steering wheel tilts up.
    12 V battery positive (+) lead → Terminal E17-2 (TIM-)
    12 V battery negative (-) lead → Terminal E17-1 (TIM+)
    The steering wheel tilts down.



NG
REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

4. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
C149089E11
  1. Disconnect the E27 multiplex tilt and telescopic ECU connector.

  1. Disconnect the E17 tilt motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E27-6 (VCI) - E17-4 (VCI)
    Always
    Below 1 Ω
    E27-7 (TIS) - E17-5 (TIS)
    E27-17 (E1) - E17-6 (E1)
    E27-6 (VCI) - Body ground
    Always
    10 kΩ or higher
    E27-7 (TIS) - Body ground
    E27-17 (E1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

  1. C149087E22
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E27-11 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)

  1. C149091E03
    Reconnect the E27 multiplex tilt and telescopic ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E17-4 (VCI) - E17-6 (E1)
    Engine switch on (IG)
    8 to 16 V
    E17-5 (TIS) - E17-6 (E1)



NG
REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)
OK


7. CHECK TILT POSITION SENSOR

  1. C149088E19
    Reconnect the E17 tilt motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E27-7 (TIS) - E27-17 (E1)
    Steering tilting up or tilting down
    Pulse generation
    High: 8 to 16 V
    Low: Below 1 V



NG
REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)


← B2603 Tilt and Telescopic Manual Switch Circuit Malfunction (from Jan 2012)B2611 Telescopic Position Sensor or Telescopic Motor Circuit Malfunction (from Sep 2011) →