2011-2013 Land Cruiser · Service Manual Steering

B2611 Telescopic Position Sensor or Telescopic Motor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Sep 2011

DESCRIPTION

The telescopic motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor detects the sliding position in the forward and backward directions of the steering column and outputs a signal to the multiplex tilt and telescopic ECU based on that sliding amount.
C152160E02

HINT:
Limit positions can be confirmed on the screen of the intelligent tester.
DTC Code
Detection Condition
Trouble Area
B2611
The telescopic operation stops within the operation range while operating.
  1. Harness or connector
  2. Telescopic position sensor or telescopic motor
  3. Multiplex tilt and telescopic ECU


WIRING DIAGRAM

C149006E07

INSPECTION PROCEDURE

HINT:
The wire harness between the multiplex tilt and telescopic ECU and telescopic motor is provided with the steering column assembly.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TELESCOPIC SHORT/LONG)
C106469E01
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the steering column contracts and extends.

    Tilt & Telescopic 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Telesco Operation
    Telescopic operation
    Long/Short
    -

Result 
Result
Proceed to
The steering column does not contract/extend.
A
The steering column contracts/extends.
B


B
Go to step 3
A


2. CHECK TELESCOPIC MOTOR

  1. C149086E06
    Disconnect connector A from the multiplex tilt and telescopic ECU.

  1. Apply 12 V battery voltage to the multiplex tilt and telescopic ECU connector. Then check the steering wheel telescopic operation.

    OK:
    Measurement Condition
    Specified Condition
    12 V battery positive (+) lead → Terminal A-2 (TEM+)
    12 V battery negative (-) lead → Terminal A-6 (TEM-)
    The steering column contracts.
    12 V battery positive (+) lead → Terminal A-6 (TEM-)
    12 V battery negative (-) lead → Terminal A-2 (TEM+)
    The steering column extends.



NG
REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

3. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)

  1. C149088E20
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A-3 (VCE) - A-5 (E2)
    Engine switch on (IG)
    8 to 16 V



NG
Go to step 5
OK


4. CHECK TELESCOPIC POSITION SENSOR

  1. C149088E21
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A-4 (TES) - A-5 (E2)
    Telescopic steering contracting or extending
    Pulse generation
    High: 8 to 16 V
    Low: Below 1 V



NG
REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

5. CHECK HARNESS AND CONNECTOR (ECU - TELESCOPIC POSITION SENSOR)

  1. C149086E08
    Disconnect connector A from the multiplex tilt and telescopic ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 (VCE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (ECU - BODY GROUND)

  1. C149087E22
    Disconnect the E27 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E27-11 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)


← B2610 Tilt Position Sensor or Tilt Motor Circuit Malfunction (from Sep 2011)B2620 ECU Power Source Circuit Malfunction (from Sep 2011) →