2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the display and navigation module display.
If there is an open in the circuit, the navigation system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the resulting condition is the same as to if the switch were continuously pressed. Therefore, the display and navigation module display cannot be operated using the steering pad switch assembly, and the display and navigation module display itself cannot function.

WIRING DIAGRAM

E194870E02

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an Supplemental Restraint System (SRS). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).


1. INSPECT DISPLAY AND NAVIGATION MODULE DISPLAY

  1. E194871E06
    Disconnect the F64 display and navigation module display connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F64-25 (SW1) - F64-23 (SWG)
    No switch pushed
    95 to 105 kΩ
    F64-25 (SW1) - F64-23 (SWG)
    Seek+ switch pushed
    Below 2.5 Ω
    F64-25 (SW1) - F64-23 (SWG)
    Seek- switch pushed
    312 to 345 Ω
    F64-25 (SW1) - F64-23 (SWG)
    Volume+ switch pushed
    950 to 1050 Ω
    F64-25 (SW1) - F64-23 (SWG)
    Volume- switch pushed
    2954 to 3265 Ω
    F64-24 (SW2) - F64-23 (SWG)
    No switch pushed
    95 to 105 kΩ
    F64-24 (SW2) - F64-23 (SWG)
    MODE switch pushed
    Below 2.5 Ω
    F64-24 (SW2) - F64-23 (SWG)
    Voice switch pushed
    2954 to 3265 Ω
    F64-24 (SW2) - F64-23 (SWG)
    On Hook switch pushed
    312 to 345 Ω
    F64-24 (SW2) - F64-23 (SWG)
    Off Hook switch pushed
    950 to 1050 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Display and Navigation Module Display)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT SPIRAL CABLE SUB-ASSEMBLY

  1. E168547E26
    Disconnect the z36 and E12 steering pad switch and spiral cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z36-8 (EAU) - E12-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z36-10 (AU1) - E12-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z36-9 (AU2) - E12-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Refer to the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *2
    Steering Pad Switch Side
    *3
    Vehicle Side



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3. INSPECT STEERING PAD SWITCH ASSEMBLY

  1. Disconnect the z36 steering pad switch assembly connector.E155690E09

Text in Illustration 
*1
Component without harness connected
(Steering Pad Switch Assembly)
*2
Volume+
*3
Volume-
*4
Seek-
*5
MODE
*6
Seek+
*7
Off Hook
*8
On Hook
*9
Voice
-
-
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z36-10 (AU1) - z36-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z36-10 (AU1) - z36-8 (EAU)
    Seek+ switch pushed
    Below 2.5 Ω
    z36-10 (AU1) - z36-8 (EAU)
    Seek- switch pushed
    312 to 345 Ω
    z36-10 (AU1) - z36-8 (EAU)
    Volume+ switch pushed
    950 to 1050 Ω
    z36-10 (AU1) - z36-8 (EAU)
    Volume- switch pushed
    2954 to 3265 Ω
    z36-9 (AU2) - z36-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z36-9 (AU2) - z36-8 (EAU)
    MODE switch pushed
    Below 2.5 Ω
    z36-9 (AU2) - z36-8 (EAU)
    Voice switch pushed
    2954 to 3265 Ω
    z36-9 (AU2) - z36-8 (EAU)
    On Hook switch pushed
    312 to 345 Ω
    z36-9 (AU2) - z36-8 (EAU)
    Off Hook switch pushed
    950 to 1050 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (DISPLAY AND NAVIGATION MODULE DISPLAY - SPIRAL CABLE)


← Black Screen (Sep 2011 – Dec 2011)Illumination Circuit (Sep 2011 – Dec 2011) →