Illumination Circuit
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
DESCRIPTION
Power is supplied to the display and navigation module display, radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the TAIL or HEAD position.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the Supplemental Restraint System (Click here).
| 1. CHECK ILLUMINATION |
Check if the illumination for the display and navigation module display, steering pad switch, glove box light, cigarette lighter, or other parts (seat heater switch, front seat memory switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
Result Result
Proceed to
Illumination comes on for all components except steering pad switch assembly.
A
Illumination comes on for all components except radio receiver assembly.
B
Illumination comes on for all components except display and navigation module display.
C
No illumination comes on for all components.
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE SUB-ASSEMBLY) |
Disconnect the E12 spiral cable sub-assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E12-12 (IL+2) - Body ground
Light control switch in tail or head
11 to 14 V
Text in Illustration *1
Front view of wire harness connector
(to Spiral Cable Sub-assembly)
|
|
||||
| OK | |
| 3. INSPECT STEERING PAD SWITCH ASSEMBLY |


| *1 |
Component without harness connected (Steering Pad Switch Assembly) |
- |
- |
Disconnect the z36 steering pad switch assembly connector.
Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead from the battery to terminal 8 (EAU) of the steering pad switch assembly connector.
Check if the illumination for the steering pad switch assembly comes on.
- OK:
- Illumination for the steering pad switch assembly comes on.
|
|
||||
| OK | |
| 4. INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Disconnect the z36 and E12 steering pad switch assembly connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z36-5 (IL+2) - E12-12 (IL+2)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z36-8 (EAU) - E12-4 (EAU)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
Text in Illustration *1
Component without harness connected
(Spiral Cable Sub-assembly)
*2
Steering Pad Switch Side
*3
Vehicle Side
- NOTICE:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the supplemental restraint system (Click here).
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - DISPLAY AND NAVIGATION MODULE DISPLAY AND RADIO RECEIVER) |
Disconnect the E12 spiral cable sub-assembly connector.
Disconnect the F64 display and navigation module display connector.
Disconnect the F56 radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E12-12 (IL+2) - F64-12 (ILL+)
Always
Below 1 Ω
E12-12 (IL+2) - F56-3 (ILL+)
Always
Below 1 Ω
E12-4 (EAU) - F64-23 (SWG)
Always
Below 1 Ω
E12-12 (IL+2) - Body ground
Always
10 kΩ or higher
E12-4 (EAU) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BATTERY AND BODY GROUND) |
Disconnect the F56 radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F56-3 (ILL+) - Body ground
Light control switch in TAIL or HEAD
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F56-17 (ILL-) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (DISPLAY AND NAVIGATION MODULE DISPLAY - BATTERY AND BODY GROUND) |
Disconnect the F64 and F62 display and navigation module display connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F64-12 (ILL+) - Body ground
Light control switch in TAIL or HEAD
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F62-1 (HILL) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
