2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Radio Broadcast cannot be Received or Poor Reception

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

INSPECTION PROCEDURE


1. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result 
      Result
      Proceed to
      Automatic station search function stops on a station.
      A
      Automatic station search function does not stop.
      B



B
Go to step 2
A

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)

2. CHECK OPTIONAL COMPONENTS
  1. Check optional components (sunshade film, telephone antenna, etc.).

    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      Result 
      Result
      Proceed to
      Optional components are installed.
      A
      Optional components are not installed.
      B

      NOTICE:
      Do not remove any optional components installed by the customer without his or her consent.



B
Go to step 3
A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3. CHECK RADIO ANTENNA
  1. Check for noise

    1. Turn the engine switch on (ACC) with the multi-media module receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire, or other metal object on the amplifier antenna threaded installation portion for the antenna and check that noise can be heard from the speakers.

      Result 
      Result
      Proceed to
      Noise does not occur.
      A
      Noise occurs.
      B



B
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
A


4. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

  1. E187251
    Preparation for check
    1. Remove the antenna connector from the multi-media module receiver assembly.

  1. Check for noise

    1. Turn the engine switch on (ACC) with the multi-media module receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the multi-media module receiver assembly antenna jack and check that noise can be heard from the speakers.

      OK:
      Noise can be heard from the speaker.



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK


5. CHECK WINDOW GLASS ANTENNA WIRE

  1. E111994E16
    Check for continuity of the antenna.

    HINT:
    Check for continuity at the center of each antenna wire as shown in the illustration.

    NOTICE:
    When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.

    OK:
    There is continuity in the antenna.

    Text in Illustration 
    *1
    Tester Probe
    *2
    Antenna Wire
    *3
    Tin Foil



NG
REPAIR WINDOW GLASS ANTENNA WIRE (Click here)
OK


6. INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
  1. Disconnect the multi-media module receiver assembly connector.

  1. E188455E30
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    RA-5 (ANT+) - Body ground
    Engine switch on (ACC)
    Radio switch on
    11 to 14 V

    Text in Illustration 
    *a
    Component without harness connected
    (Multi-media Module Receiver Assembly)



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK


7. CHECK ANTENNA CORD SUB-ASSEMBLY
  1. Remove the antenna connector of the multi-media module receiver assembly and antenna.

  1. Measure the resistance between the antenna and multi-media module receiver assembly to check for an open circuit in the antenna cord.

    Standard resistance:
    Below 1 Ω

  1. Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

    Standard resistance:
    10 kΩ or higher



NG
REPLACE ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


8. CHECK AMPLIFIER ANTENNA ASSEMBLY
  1. Replace the amplifier antenna assembly and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received.



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK

END


← Radio Broadcast cannot be Received or Poor Reception (Sep 2011 – Dec 2011)Illumination for Panel Switch does not Come on with Tail Switch ON (from Jan 2012) →