P0500 Vehicle Speed Sensor "A"
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
Vehicles which are equipped with a manual transmission detect the vehicle speed using the speed sensor. The speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Vehicle being driven |
Conditions (a), (b), (c) and (d) are met for 8 seconds or more (2 trip detection logic): (a) Engine coolant temperature is more than 70°C (158°F). (b) Engine speed is between 1500 and 4000 rpm. (c) Vehicle is running. (d) No speed signal is input to the ECM. |
|
| Drive vehicle during fuel-cut operation |
Conditions (a), (b) and (c) are met for 5 seconds or more (2 trip detection logic): (a) Vehicle is running. (b) During the fuel-cut operation. (c) No speed signal is input to the ECM. |
| DTC No. |
Data List |
| P0500 |
Vehicle Speed |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK OPERATION OF SPEEDOMETER |
Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.
- HINT:
- The vehicle speed sensor is operating normally if the speedometer reading is normal.
- If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the tester.
- OK:
- Vehicle speeds displayed on tester and speedometer display are equal.
|
|
||||
|
|
||||
| 3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM) |
Disconnect the combination meter connector.
Disconnect the ECM connector.
Measure the resistance according the value(s) in the table below.
- Standard Resistance (Check for Open):
for LHD Tester Connection
Condition
Specified Condition
E7-4 (+S) - A38-8 (SPD)
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
E7-4 (+S) - A52-8 (SPD)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
for LHD Tester Connection
Condition
Specified Condition
E7-4 (+S) or A38-8 (SPD) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
E7-4 (+S) or A52-8 (SPD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE) |
![]() ![]() |
Disconnect the combination meter connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E7-4 (+S) - Body ground
Ignition switch ON
4.5 to 5.5 V
Reconnect the combination meter connector.
|
|
||||
| OK | |
| 5. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM) |
![]() ![]() |
Remove the combination meter.
Connect the combination meter connector.
Move the shift lever to N.
Jack up the vehicle.
Check the voltage between the terminal of the combination meter and the body ground while a wheel is turned slowly.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E7-4 (+S) - Body ground
Ignition switch ON
Voltage generated intermittently
- HINT:
- The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
Reinstall the combination meter.
|
|
||||
|
|
||||
| 6. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM) |
![]() ![]() |
Remove the combination meter.
Connect the combination meter connector.
Move the shift lever to N.
Jack up the vehicle.
Check the voltage between the terminal of the combination meter and the body ground while a wheel is turned slowly.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E7-4 (SI) - Body ground
Ignition switch ON
Voltage generated intermittently
- HINT:
- The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
Reinstall the combination meter.
| Test result |
Proceed to |
| OK (w/ Multi-information Display) |
A |
| OK (w/o Multi-information Display) |
B |
| NG |
C |
|
|
||||
|
|
||||
|
|
||||
| 7. CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE ACTUATOR) |
Disconnect the combination meter connector.
Disconnect the brake actuator connector.
Measure the resistance according the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
E7-3 (SI) - A24-12 (SP1)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
E7-3 (SI) or A24-12 (SP1) - Body ground
Always
10 kΩ or higher
Reconnect the combination meter connector.
Reconnect the brake actuator connector.
|
|
||||
| OK | ||
| ||



