2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Illumination Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E159230E02

INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution for the SRS (Click here).

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK ILLUMINATION
  1. Check if the illumination for the steering pad switch, glove box light, cigarette lighter, or others (seat heater switch, front seat memory switch, etc.) comes on when the light control switch is turned to the head or tail position.

    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except radio receiver.
    B
    No illumination comes on for radio receiver, glove box light, front seat memory switch, cigarette lighter, etc.
    C



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)
A


2. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - TAIL RELAY)
E172054E01
  1. Disconnect the E12 cable connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E12-12 (IL+2) - Body ground
    Light control switch tail or head
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral Cable)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT STEERING PAD SWITCH ASSEMBLY
E155691E01
  1. Disconnect the z36 switch connector.

  1. Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 5 (IL+2)
    Battery negative (-) → Terminal 8 (EAU)
    Light illuminates



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4. INSPECT SPIRAL CABLE SUB-ASSEMBLY
E160954E12
Text in Illustration 
*a
Steering Pad Switch Side
*b
Vehicle Side
  1. Disconnect the E12 and z36 cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E12-12 (IL+2) - z36-5 (IL+2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 3 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    E12-4 (EAU) - z36-8 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 3 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)
  1. Disconnect the F19 receiver connector.

  1. Disconnect the E12 cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F19-6 (SWG) - E12-4 (EAU)
    Always
    Below 1 Ω
    F19-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - TAIL RELAY AND BODY GROUND)

  1. E106746E29
    Disconnect the F35 receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F35-7 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F35-10 (ILL+) - Body ground
    Light control switch
    tail or head
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio Receiver)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)


← Illumination Circuit (Sep 2011 – Dec 2011)Speaker Circuit (Sep 2011 – Dec 2011) →