2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Speaker Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The radio receiver sends sound signals to the speakers.

WIRING DIAGRAM

E156715E02

INSPECTION PROCEDURE


1. CHECK SPEAKER
  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 7
A


2. CHECK SPEAKER
  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Front No. 2 speaker
    A
    Front No. 1 speaker
    B



B
Go to step 5
A


3. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E144969E46
    Disconnect the F8 and F7 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω
    3 - 4
    Always
    Below 1 Ω
    2 - 4
    Always
    8 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 2 Speaker)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 2 SPEAKER)
  1. Disconnect the F35 receiver connector.

  1. Disconnect the F8 and F7 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    F35-2 (FL+) - F8-1 (+)
    Always
    Below 1 Ω
    F35-6 (FL-) - F8-3 (-)
    F35-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    F35-6 (FL-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    F35-1 (FR+) - F7-1 (+)
    Always
    Below 1 Ω
    F35-5 (FR-) - F7-3 (-)
    F35-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    F35-5 (FR-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)

5. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E107214E17
    Disconnect the I10 and I1 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)
  1. Disconnect the I10, I1, F8 and F7 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    F8-2 (TWL+) - I10-1
    Always
    Below 1 Ω
    F8-4 (TWL-) - I10-2
    F8-2 (TWL+) - Body ground
    Always
    10 kΩ or higher
    F8-4 (TWL-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    F7-2 (TWR+) - I1-1
    Always
    Below 1 Ω
    F7-4 (TWR-) - I1-2
    F7-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    F7-4 (TWR-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)

7. INSPECT REAR SPEAKER SET

  1. E107214E17
    Disconnect the J17 and J15 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Speaker Set)



NG
REPLACE REAR SPEAKER SET (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR SPEAKER SET)
  1. Disconnect the F36 receiver connector.

  1. Disconnect the J17 and J15 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    F36-2 (RL+) - J17-1
    Always
    Below 1 Ω
    F36-6 (RL-) - J17-2
    F36-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    F36-6 (RL-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    F36-1 (RR+) - J15-1
    Always
    Below 1 Ω
    F36-3 (RR-) - J15-2
    F36-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    F36-3 (RR-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)


← Illumination Circuit (from Jan 2012)Speaker Circuit (from Jan 2012) →